Search:

Type: Posts; User: OldGinTractors; Keyword(s):

Results 1 to 90 of 90

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    1,150

    Re: New 4530

    Great choice Captain. ENJOY!
  2. Re: The financing game - what's the real deal?

    The nice thing about Mahindra's financing is they give you that 84 month option to keep your payments within your budget. Every deal we figure @ 0% for 84 months will be the lowest price if you pay...
  3. Re: Westendorf FEL and Mahindra 6500 4wd hydraulics question

    Yes you need to plumb the hydraulics direct. There is a union in the pressure line from the pump that you can tap into but make sure your loader valve has a relief valve built into it.
  4. Replies
    2
    Views
    293

    Re: Mahindra 5500 won't start

    Most likely a safety switch. The transmission switch is located under the right floorboard and the wires can be pulled loose fairly easily if you get out in brushy areas. The pto switch is located...
  5. Loader Re: Cannot articulate bucket while in Float Mode

    Lou,

    The fast dump feature is what I call a regen feature. It doesn't increase the speed the bucket dumps under normal no load conditions, but if you have a heavy load in the bucket and dump it...
  6. Replies
    5
    Views
    327

    Re: 2615 HST Brake Stuck???

    Hydros need lots of RPM to perform well, so run at least 2000 RPM. As stated, high range is just for traveling and if your tires are loaded it will also magnify the problem.
  7. Replies
    8
    Views
    451

    Re: Mahindra 5525 Wont Start

    Be sure to pump the primer pump several times after closing the banjo bolt, the pump should begin to get hard to pump if the air is out.
  8. Replies
    81
    Views
    10,702

    Re: eMax 22/25 info?

    Never thought I would make the pages of tractorbynet but there in the background of the outdoor picture are some of the Arkansas delagation, yours truly in the blue shirt discussing the new EMax with...
  9. Re: Mahindra 4530 4WD Spitting/Backfiring

    Before jumping into the timing issue make sure you check fuel flow. I would change the fuel filters and when you have the primary filter off turn the fuel on and make sure you have full flow from...
  10. Replies
    7
    Views
    369

    3-Point Hitch Re: 2810 hst

    Check the rate of drop knob located just under the seat.
  11. Replies
    8
    Views
    642

    Re: 4035 PST will not start

    Here's a couple of suggestions. First make sure you have 12 volts at the shut off solinold on the injector pump. I would not pull the injectors, I don't think that is the problem. Does the manuel...
  12. Re: increasing the reverse speed of my HST mahindra

    The 2815 has a stop screw under the floorboard that can be adjusted to give the petal more travel.
  13. Thread: 4530??

    by OldGinTractors
    Replies
    3
    Views
    517

    Re: 4530??

    It came with the 509 hoe built by bradco at one time. That's a very good machine.
  14. Replies
    81
    Views
    10,702

    Re: eMax 22/25 info?

    The EMAX is not the same tractor as the Max 22 or 25. It's made for those folks that just could not get their head wrap around the fact that Mahindra called the Max a subcompact. LOL So to appease...
  15. Thread: 4025

    by OldGinTractors
    Replies
    2
    Views
    309

    Re: 4025

    Yes the 25 series has that plug on the lower radiator hose. That same heater should fit the 6000 as well.
  16. Buying Advice Re: JD 3038e vs Mahindra 3016 almost same price

    Great choice, the Mahindra 3616 is a very capiable machine, much more than JD3038. That price sounds very good too.
  17. Replies
    7
    Views
    612

    Re: bush hog size

    I agree with Bill, 5 ft. would be my choice.
  18. Replies
    6
    Views
    475

    Re: Also to 8560 owners

    No, you won't have to. I just take the plug out and screw the heater with a wrap of teflon tape on it in. Leave the cap on the radiator so the system can't get air and you lose maybe a pint of...
  19. Replies
    6
    Views
    475

    Re: Also to 8560 owners

    The 8560 has a 3/4 inch pipe plug just above the starter to install a block heater. Katts makes a 400 watt heater that will screw right in. Works great.
  20. Replies
    3
    Views
    339

    Re: 7520 beeping randomly

    That warning beeper is tied into the transmission lube oil circuit. It will sound if there is low pressure for an extented length of time. I think its 5 mins. The sending unit is located on the...
  21. Replies
    4
    Views
    464

    Re: transmission oil

    I recommend my customers use a premium universal tractor transmission/hydraulic fluid. I sell Mahindra fluid as well as Troco brand that is a little less expensive(selling it for 40 years) but just...
  22. Replies
    4
    Views
    380

    Re: Mahindra 6000 Loader

    The ML264 is build by KMW for the 5500 and 6500 4 wheel drive. It is heavier duty and made higher for clearing the front wheels. The ML260 has been manufactured by Buhler and GB and is designed...
  23. Replies
    12
    Views
    1,228

    Comparison Re: Mahindra 2816

    And I thought bombardier was a atv company! My bad, on second thought I guess they are but the 4 wheeler I was thinking about won't be carrying that animal.
  24. Replies
    12
    Views
    1,228

    Comparison Re: Mahindra 2816

    2816 is a great tractor with no major issuses. It was make for several year and also wore a Cub Cadet badge for a few years. Parts should be no problem. The only down side for me is the 9x3...
  25. Replies
    18
    Views
    1,656

    Re: 5530 Back to the dealership.

    I would not worry to much about the light till you get some hours on your 5530. It will always come on till the engine gets to operating temp. If it is still binking a code after you get 50 or so...
  26. Re: Mahindra 4035 PST shuttle lever adjustment for neutral safety switch

    Just spray a little PB blaster on the detent mechanism will cure the problem. It is something you may need to do as regular manitence to keep the shift lever working smoothly.
  27. Replies
    11
    Views
    1,182

    Re: 2615 Oil Leak

    I think 14 is a drive in plug like a feeze plug.
  28. Replies
    28
    Views
    1,634

    Re: 3215 Broken bolt in Front Axle

    Have you called your nearby dealers. I use the USPS to sent my customer small parts. Maybe all those online sellers are shipping direct from Mahindra USA, if so there is extra cost in sending...
  29. Buying Advice Re: John Deere 5055E w/ FEL vs. Kubota MX5200 4 wheel drive with FEL

    I think that a Kubota M5640SU would be a much fairer comparision to the JD5055.
  30. Replies
    5
    Views
    421

    Loader Re: Shift lever problems

    I have seen some of the loader valves get enough oil and condensation in the end cap to become hydro-locked. You would need to take the cap off and clean it out. Also have seen the orings that...
  31. Replies
    4
    Views
    467

    Loader Re: 4035 Lift Capacity

    Remember that the 2400 is at the pins. If the tank was only a couple of feet in diameter it might do it but if it is 4 foot square you better put the neighbor on standby.
  32. Replies
    6
    Views
    676

    Re: New 509 Backhoe

    LAP POOL?
  33. Replies
    4
    Views
    513

    Re: Front axle pinion removal

    You will need a slide hammer. New England described the set up you need. You will need to buy another coupler but there inexpensive. The nut just holds the bearing on the shaft.
  34. Re: 2009 Mahindra 6000 - stuck in first gear

    Not much of a problem to pull the top off. I have had one that the detent ball got rusted up and cause the shifter to become hard to move but i believe it was the hi-low shift. Hopefully yours will...
  35. Replies
    9
    Views
    703

    Re: LEAKS ???

    That's great news on both fronts. I have one of those son-in-laws in my near future also.
  36. Replies
    2
    Views
    379

    Re: 800 Hour Service Light

    Brandi,
    It's just the service reminder light. Should have come on at 300 and 550 hours.
  37. Replies
    4
    Views
    425

    Re: service light

    Looks as you have a cab model. The reset is located in the fuse box behind the step light. It is marked on the fuse box cover. Just insert a fuse ito the slot, turn the switch on for a few...
  38. Replies
    5
    Views
    774

    Re: Mahindra tractor keys

    You can buy one from your local Mahindra dealer or if you have a Kubota dealer near some of ther models use the same key.
  39. Replies
    8
    Views
    563

    Re: Drill seeder?

    I don't believe your 3616 will be big enough to run the no-til seeders that the county extention office has for loan. Our county has a 10 ft. Hayvan that would take 60 HP or more.
  40. Replies
    1
    Views
    446

    Re: Broken 5035

    I know it's disappointing to have these problems but the 35 series are great tractors. Hopefully you'll get the bugs worked out and get years of touble free service from your 5035. I will have to...
  41. Replies
    9
    Views
    703

    Re: LEAKS ???

    Mahindra offers a kit that contains the seals in the pump. You must remove the pump and disassemble it to install the kit, if you are mechaniclly inclined go for it, if not seek help. You may want...
  42. Replies
    9
    Views
    703

    Re: LEAKS ???

    Is your power steering making oil? You need to take out any extra fluid and get the level at the mark on the dipstick, run it a couple of hours and see if it made any fluid. If it gained the...
  43. Replies
    3
    Views
    440

    3-Point Hitch Re: 3 point hitch

    You may want to look into purchasing a Quick-hitch. If your equipment is compatable it makes hooking up a beeze.
  44. Replies
    2
    Views
    325

    Re: 3505 di air filter element

    That seems high for that filter. Shop around at another dealer or on the net, should find it for $25 or so. I don't understand dealers that mark up filters to the point of running there customers to...
  45. Replies
    4
    Views
    434

    Re: Questions about 3016.

    You will need to replace the filter, cleaning it will not do much good. Also get a new oring , that should take care of the leak.
  46. Oil & Fuel Re: Mahindra spitting and sputtering and it will not start

    Check the fuel flow from the tank. Did you check for a screen in the tank when you had it drain. Many of the 00 series has a screen above the shut off valve.
  47. Re: Widening my tire stance on my 6110/ good or bad?

    I believe swaping sides will give you 8" spread per side.
  48. Replies
    4
    Views
    621

    Re: Mahindra 5035 PST PTO Fuse

    I think I can help. The shuttle lever rubs the wires coming out of the pto switch. Pop the switch out and inspect the wires, it doesn't take but a little wire exposed to blow the fuse. Tape the...
  49. Replies
    2
    Views
    396

    Re: Another steering cylinder question

    It is right hand threads, be sure to loosen set screw that locks hat nut. There is also seals in that opposite end that will need replacing too.
  50. Replies
    14
    Views
    1,163

    Re: Looking to upgrade

    Congrats, did you go cab hydro or gear? I think you will be happy with Mahindra.
    Dave
  51. Replies
    32
    Views
    2,743

    Re: New max 28 and new member

    Nine years selling Mahindra's, this has to be a freak failure. I have seen broken diffs, striped couplers, and broken axles but not on brand new tractors. Those failures happen on abused, misused...
  52. Replies
    3
    Views
    306

    Re: 7520 and Power Steering Tank

    It is possible for the power steering to exchange fluid with the hydraulic transmission fluid and overflow the PS tank. If that is happening the seals will need to be replaced between the pumps.
    ...
  53. Replies
    6
    Views
    625

    Re: Filter cross over 8560

    Did your dealer tell you how to reset the service light? Hopeful so. Sounds like a fair price for filters and I think you will be thankful for supporting your dealer and he will be thankful of the...
  54. Replies
    54
    Views
    5,578

    Re: 4035 spits and sputters at high rpms

    I have had no problems with timing on 35 series tractors. Replace the fuel lines from the tank and it will most likely fix your problem.

    Dave
  55. Replies
    283
    Views
    17,670

    Re: Kids not allowed at Tractor Dealership?

    I saw a great sign at one of our local businesses. "Unattended children will be given an expresso and a puppy." Most parents will understand the message along with a chuckle.
  56. Replies
    20
    Views
    2,478

    Buying Advice Re: 48~75HP, 4WD, CAB, Made in the USA ???

    I maybe a little bais, but the Mahindra 6110 is a alot bang for the buck. Like all the others, not made in USA but some assembly in Texas. I am pretty close to you too. Live down the road in...
  57. Replies
    54
    Views
    5,578

    Re: 4035 spits and sputters at high rpms

    I think if its pulling the primer down there is a restriction somewhere between the tank and filter.
  58. Replies
    54
    Views
    5,578

    Re: 4035 spits and sputters at high rpms

    My experience with the 35 series fuel system problems have been in the fuel lines. Check the delivery line where it enters the engine compartment, it is nomally tied with nylon ties to the return...
  59. Replies
    43
    Views
    1,895

    Re: Putting on a loader on a JD 830 1974

    Does your JD 830 have a rear remote? If so you can pump the pressure and return hose to it but will have to tie the remote valve open when operating loader.
  60. Replies
    4
    Views
    721

    Re: Oil Filter Campatibility Question

    If your tractor is a Tier 3 that is the filter Mahindra recommends, if is Tier 2 the shorter filter is the correct one. IMO I don't think it will cause any ill effects to use the longer filter on...
  61. Re: My thoughts and some ???'s Mahindra 4035

    Your tractor being an early model should have the flat steering wheel, the newer 35 series have a steering wheel with more dish to bring it closer the the driver. You might check with your local...
  62. Re: I need better information on the maintenance of a 6500 Mahindra.

    I believe the heater relay/timer module on 00 series is bolted inside the brace that runs from the top of the radiator to the firewall on the left side of the tractor.

    Dave
  63. Replies
    8
    Views
    590

    Re: 5035 Fuel System Leaks

    Fuel lines have been an issue on these models. You should ask your dealer to replace all the fuel lines that run to the tank, cause it's a pretty good job getting the tank loose to get to the...
  64. Replies
    72
    Views
    17,321

    Re: Mahindra 100 hp tractor

    Well said Dave! Mahindra is on the Rise.
  65. Replies
    16
    Views
    3,752

    Re: mahindra 3616 oil filter?

    Mahindra, Deere, Kubota , New Holland and any other tractor maker that I know of manufactures their own filters. The filters are made to each makers specs by companies like wixs, baldwin, fram and...
  66. Re: What Mahindra tractor compairs to Kubota L3200 L3800

    The 3016 and 3616 are good comparisons but I would also look at the 4010. The 4010 hydro is a really nice tractor with the 2 petal controls and left side turning brakes, also all these mahindra's...
  67. Replies
    9
    Views
    699

    Oil & Fuel Re: transmission dip stick problem

    I have a customer that has had this happen. We just replaced the dipstick a couple of weeks ago. The one that was chewed on was straight, no bent at all. The replacement had a bend about 3 inches...
  68. Replies
    3
    Views
    665

    Re: 4500 battery

    The best way to get the battery out is taking the 5 small bolts out of the red sheet metal under the grill and removing the horn or bent it up a little. Then you can roll the battery out the front.
  69. Replies
    6
    Views
    495

    Re: 4530 TEMP GAUGE PROBLEM

    There are 2 sensors. One for the temp gauge and another for the KSB injection timing. Sounds like the one for the temp gauge might not be connected.

    Dave
  70. Replies
    2
    Views
    602

    Loader Re: 5525 with ML 250 loader problem

    Mark, Sometimes the detent balls in the valve get rusted and cause it to hang up. You can take the rear cap off the spool to get to the detent and clean them up. Your local dealer should be able...
  71. Replies
    10
    Views
    1,630

    Re: mahindra 4110 overheats

    Lowrider, My advice is to take the side panels off and take the 4 or so bolts out that hold the air cleaner on and move it aside. Take a light and put in behind the radiator and look through it...
  72. Replies
    29
    Views
    6,851

    Re: How do I get clean cut with Brush Hog?

    Did your old cutter have a stump jump or just a blade bar? Normally a cutter with a large round blade carrier will not cut as clean as one with just a bar. Also lots of old cutters used shorter...
  73. Re: Baling small square bales from center of field, out

    A older fellow that customed bale for many years told me he waited last to bale the two outside windrows because that's where that limb would be raked up in the windrow, thrust breaking a needle or...
  74. Replies
    40
    Views
    6,064

    Re: Delivery is Bitter Sweet

    The handle pretty much locked up so I did the strip down and unhooked the cable to see if the cable could be seized, but it worked fine. Took the detent ball and spring apart and it was a little...
  75. Replies
    40
    Views
    6,064

    Re: Delivery is Bitter Sweet

    Chris,

    There is a detent ball for the PST handle that needs a little lube. You can pull the rubber grommet from around the handle and shoot a little PB Blaster on the ball and spring under the...
  76. Replies
    24
    Views
    2,376

    Re: New guy-New tractor

    Steve,

    The ipto is easy, the long handle is just a clutch, pull it foward and lock it in position ( like holding down clutch pedal) now reach back to the shift handle located just behind the ipto...
  77. Replies
    11
    Views
    3,652

    Re: Deutz 3006

    Rick,

    I sold deutz tractors in the 70's and 80,s and still work on many. They are a very good tractor although they are getting old and some of them out there are just plain worn out. Let me...
  78. Replies
    22
    Views
    1,739

    Re: Looking for comparable tractor to 8N.

    Great choice in the 3016. Better close the deal if dealer has one in stock, I have been waiting for a couple of months for more 3016's.
  79. Replies
    7
    Views
    2,106

    Re: Mahindra 6110 AC Problems

    I sure think you have a warranty issue. If you were my customer I would want to get your problem solved. Unless you have some A/C training I would get it back to the dealer. How far are you...
  80. Replies
    7
    Views
    1,030

    Re: Mahindra 4110 Clutch

    Skipmarcy could be right, I have seen that a couple of times. It could also be the pilot bearing locked up.
  81. Replies
    6
    Views
    834

    Re: elec.w/2310 mahindra

    The 10 series have several fuseable links in the wiring harness. There is one for the starting circuit and one for the preheat circuit. They look like a loop of wire that plugs into the harness.
  82. Replies
    10
    Views
    1,623

    Price Check Re: 3316 Pricing

    The 3616 replaced the 3316 last year. There are a few 3316's left over in dealer inventories. Pretty much the same tractor other than the horsepower and the 33 uses a different steering cylinder...
  83. Replies
    28
    Views
    2,508

    Re: Performance Loss to engine shut down

    Worked on a 2516 a few weeks back with pretty much same symtoms. Turned out to be trash in the bottom of the tank. Drained and cleaned tank and has been running fine since.
  84. Replies
    11
    Views
    822

    Re: power steering

    Ted, Steering valve shaft seal is leaking, kit is pretty inexpensive but its quite a job getting the valve out and in. BTW steering should be using ATF dextron fluid.

    Dave
  85. Buying Advice Re: So i go into the Kubota dealer this afternoon who also sells Mahindra's

    Congrats! Nice choice too.

    Dave
  86. Replies
    8
    Views
    885

    Buying Advice Re: New Backhoe for old tractor

    I'm with Galen. That's a good buy and a great fit. Mahindra will finance equipment over $2500. You better pull the trigger soon the power may go bad.

    Dave
  87. Replies
    1
    Views
    1,469

    Re: 4025 4wd vs 4035

    Yes The 4035 is a bells and whistle tractor and the 4025 is just a plain Jane. You can also throw the 4010 in there for a middle of the road 40 hp compact tractor.

    Dave
  88. Re: Mahindra Gas Gauge - which end is up?

    Rickstir,

    The plastic fuel tank could have collsaped if your tractor is a few years old. I had a couple that had that problem when the metal insert in the cap got turned upside down and would not...
  89. Replies
    4
    Views
    1,045

    Re: Mahindra 4510 Where is it built

    Tractor and engine in South Korea and the Mahindra loader is USA.

    Dave
  90. Re: Emissions Light missing on 2010 Mahindra 6530

    I believe they moved the light into the dash panel. Should be a ! in a circle. The manual could not be the newest version.

    Dave
Results 1 to 90 of 90
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.