Search:

Type: Posts; User: robmc5; Keyword(s):

Results 1 to 14 of 14

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    956

    Re: Another Jinma Overheating problem!

    Thanks for all the suggestions. I was planning on ordering another temp gauge from Affordable today but I will see if they have a better one. My battery is in the front but it sits real low, I dont...
  2. Replies
    11
    Views
    956

    Re: Another Jinma Overheating problem!

    I do not, the over flow just hangs off the side. I remember last summer that when the tractor started getting hot the coolant would drain out of the tube, it no longer does that. I am just using...
  3. Replies
    11
    Views
    956

    Another Jinma Overheating problem!

    I have a 2003 Jinma 254 (FarmPro) Y385T Engine that started running very hot, well at least that is what the gauge says, there is no coolant coming out of the overflow. I can run it for 30 minutes...
  4. Replies
    11
    Views
    3,007

    3-Point Hitch Re: Farm Pro (Jinma) 2425 hitch will not stay up

    Update for Ron and anyone following this thread -

    I got the tractor back and decided to take a look at it myself, the first thing I noticed was that the hydraulic fluid was not full, not a good...
  5. Replies
    11
    Views
    3,007

    3-Point Hitch Re: Farm Pro (Jinma) 2425 hitch will not stay up

    Ron, I took it to a local John Deere shop here and they took the relief manifold apart, and pulled the piston. They also replaced the oil and a couple of O rings. They reassembled it and its still...
  6. Replies
    11
    Views
    3,007

    3-Point Hitch Re: Farm Pro (Jinma) 2425 hitch will not stay up

    Ron I pulled the rear valve out yesterday and here is what I found.

    388918
    I dont know if this is the correct valve, its the one behind the first pics I send and above the lever. I removed the...
  7. Replies
    11
    Views
    3,007

    3-Point Hitch Re: Farm Pro (Jinma) 2425 hitch will not stay up

    Ron,

    Thanks again for all the help on this problem. I will pull the back valve this week (maybe today) and see what it looks like, I will post more pics if I see a problem.
  8. Replies
    11
    Views
    3,007

    3-Point Hitch Re: Farm Pro (Jinma) 2425 hitch will not stay up

    Ron, thank a lot for the help, especially the diagram. I finally got out to work on it yesterday and tried to flush it like you suggested, but that did not help. I did pull what I think is the...
  9. Replies
    11
    Views
    3,007

    3-Point Hitch Re: Farm Pro (Jinma) 2425 hitch will not stay up

    Ron, thanks for the reply. I definitely will check the relief value, I found some other posts from you that talk about getting a rebuild kit for the 3PH. I did find a manual online at
    ...
  10. Replies
    11
    Views
    3,007

    3-Point Hitch Farm Pro (Jinma) 2425 hitch will not stay up

    Hello again, I have a Farm Pro (Jinma) 2425 that the hitch will not stay up. There is a adjustment knob under the seat that controls the rate of drop ( I think) and if I tighten it all the way the...
  11. Mowing Re: Newbie question about bushhog and finishing mower

    Thanks again for all the responses, the tractor was recently maintained. I am now mowing at 540 with the engine at about 2400 RPM, she'd running fine!!
  12. Mowing Re: Newbie question about bushhog and finishing mower

    Thanks for all the replies, I ran the finishing Mower at 540 at around 2000 RPM yesterday for a few hours and it was fine, no overheating and definitely not as loud, it cut the grass fine. I plan on...
  13. Mowing Re: Newbie question about bushhog and finishing mower

    rtimgray and HEC, thanks for the quick replies. I do have the marks on the tach and I have been running it around 2000 RPM (the green line is there). I have had the tractor for less than a month...
  14. Mowing Newbie question about bushhog and finishing mower

    I recently came across a deal on a FarmPro 2025 hp 4x4 tractor with a bush-hog, box-blade and finishing mower. I have never owned a tractor but since I just built a house on about 10 acres I really...
Results 1 to 14 of 14
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.