Search:

Type: Posts; User: wwalker1959; Keyword(s):

Results 1 to 29 of 29

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    255

    Re: Simple question re: Oil Capacity...

    Not bad. You must have moved quickly!
  2. Replies
    4
    Views
    255

    Re: Simple question re: Oil Capacity...

    I just did my 200 hour oil change on my T353 HST. About 5 quarts on the engine oil. I'm not sure how much hydraulic fluid you would loose if you changed out the filter without draining. If there is a...
  3. Replies
    3
    Views
    573

    Loader No damage was done to the cylinder. The only...

    No damage was done to the cylinder. The only damage was to the side plate. I'll post some pictures later today.
  4. Replies
    3
    Views
    573

    Loader FEL Pin Failure

    I have almost 200 hrs on my T353. I have been using it to clear trees and brush I perpetration for building.

    The left hand cylinder pin failed on the bucket tilt assembly. When I say failed, this...
  5. Replies
    2
    Views
    482

    Re: Trailer brakes for TYM 1003

    I'm assuming you have the wet disk brakes that came standard. If that is the case an electic brake controller would be easier.
  6. Replies
    2
    Views
    656

    Re: TYM T353 Engine Cover Latch Problems

    I plan on extending the attachment of the cable out another inch or so and changing the angle of the cable to increase the leverage. I also plan on drilling a small hole directly below the latch to...
  7. Replies
    2
    Views
    656

    TYM T353 Engine Cover Latch Problems

    I have a T353 with 125 hours on it and am having difficulty with the engine cover latch being difficult to operate. Since I am working in very dusty conditions I am opening the cover to clean filters...
  8. Re: TYM 353 HST PTO -- how to dis-engage so it rotates freely ??

    Yes. Sorry - the right side is the mid PTO. The rear is on the left.
  9. Re: TYM 353 HST PTO -- how to dis-engage so it rotates freely ??

    Make sure the electronic engagement is off and also the PTO lever on the right side of the drivers seat is in the "off" position. It should turn by hand.
  10. Replies
    1
    Views
    489

    Re: forward / reverse shift lever

    I have a T353 HST. Shifting between ranges frequently requires a little help on the gear mesh with trying to move forward or backwards a little. Just wondering if the synchronization issue exists on...
  11. Replies
    4
    Views
    1,049

    Re: Best dealer central Texas?

    I bought my T353 through VN Tractors in Mesquite. Rodney was very helpful and open with the infpormation. Service has been top notch as well. Getting some parts has taken longer than I thought it...
  12. Replies
    1
    Views
    435

    Any hydraulic shop should be able to fabricate a...

    Any hydraulic shop should be able to fabricate a new one. I have a ski boat that uses hydraulic lines for the trim and found that the independent shops could make a better hose with a stainless...
  13. Replies
    5
    Views
    692

    Backhoe I've owned and operated Massey-Fergusons, Fords,...

    I've owned and operated Massey-Fergusons, Fords, and John Deeres over the last 40 years. I realize technologies evolve and comparing a modern tractor to something built in the 70s and 80s is not...
  14. Replies
    5
    Views
    692

    Backhoe BT300 Backhoe Removal / Installation

    I took the backhoe off of my T353 for the first time to use a couple of other implements. I'm impressed with the desighn and ease of removing and re-attaching the backhoe. It litteraly took less than...
  15. Re: Gauging Some Interest on A Weld-it-Your-Self Product Line

    I think it's a great idea.

    I have a Miller wire welder and Hobart stick welder but don't have the room right now bringing in large pieces of metal or a torch table. If I leave the material...
  16. Replies
    2
    Views
    408

    Oil & Fuel Re: T353 Oil Leak

    The dealer found some loose bolts on the inside of the wheel assembly. Quick fix.

    One thing we noticed on checking the oil is the oil sight glass is extremely sensitive to the angle of the...
  17. Replies
    2
    Views
    408

    Oil & Fuel Re: T353 Oil Leak

    At 25 hours the oil level had falen to just below the minimum operating level. I added two gallons of oil and returned the level to the minimum operating range. We were operating a chipper and since...
  18. Replies
    2
    Views
    408

    Oil & Fuel T353 Oil Leak

    I have less than 20 hours on a 2013 T353 and noticed oil had leaked from somewhere on the left rear axle housing down to the backhoe frame. The oil level when I bought the tractor was well above the...
  19. Replies
    4
    Views
    587

    Mowing Re: Mid Mount Mower for TYM T353

    Thanks for the input. Sounds like the design flaw may have been fatal. It may be better to wait on the new ones that are scheduled to come out and see if they have the same weak link.
  20. Replies
    4
    Views
    587

    Mowing Mid Mount Mower for TYM T353

    Does anyone have any experience with a mid mount mower for a TYM? I understand TYM offered them in the past but discontinued them. Was it a quality control issue? Any input would be appreciated.
    ...
  21. Replies
    23
    Views
    2,072

    Grading Re: Clearing Stumps

    Model# BG-11. Bought it at Northern Tool.
  22. Replies
    23
    Views
    2,072

    Grading We finally got some good weather and started to...

    We finally got some good weather and started to tackle the 200+ stumps in front of us. Many thanks for all of the advice and input received here. We were all amazed with what we were able to...
  23. Replies
    6
    Views
    641

    Can anyone tell me what the small button on the...

    Can anyone tell me what the small button on the FEL controller is for?
  24. Replies
    23
    Views
    2,072

    Grading I had never heard of a Brush Grubber before....

    I had never heard of a Brush Grubber before. Looks like a great time saver. Thanks for the tip.
  25. Thread: New T353

    by wwalker1959
    Replies
    7
    Views
    1,880

    Re: New T353

    I just bought a 2013 HST model with a TYM frame mounted backhoe for 24,700 which means the tractor and FEL were roughly 18,000. Looks like a $1,000 swing from one part of the country to another. Does...
  26. Replies
    6
    Views
    641

    Re: FEL control

    Batwing -

    I have only put about 4 hours on my T353 so far but have not seen the same problem and we are seeing temperatures in the low 20s to mid 30s for the day. One thing I have noticed is on...
  27. Replies
    23
    Views
    2,072

    Grading Re: Clearing Stumps

    Most of the stumps are from cedars that run 6 inch trunks or less. Only have a few dead oaks we had to cut down that were 12 inches or more. Those will need to be dug up. One thing I do have going...
  28. Replies
    23
    Views
    2,072

    Grading Re: Clearing Stumps

    Thanks for the advice. I'm sure by the time I get to double digits I'll have a good feel for what it will take! Not planning on getting in a hurry as we have almost a year before we start pouring...
  29. Replies
    23
    Views
    2,072

    Grading Clearing Stumps

    I have a TYM T353 HST with a TX3500 FEL and BT300 backhoe. I am in the process of clearing a couple of acres of land that was heavily wooded. We have a couple of hundred stumps to clear and we left...
Results 1 to 29 of 29
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.