Search:

Type: Posts; User: DLTTrekkers; Keyword(s):

Results 1 to 100 of 467
Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Re: 3040 JD hydraulic oil leak Help needed.

    expansion balloon .....no ! Oil comes from the main seal in the mainhydraulicpump to the top off the tank and then back to the gearshiftcover. That "bolt" ontop of the tank has a oneway checkvalve...
  2. Replies
    1
    Views
    543

    Re: Case 674 Warning Lights

    Photo ?
  3. Replies
    23
    Views
    1,542

    Re: Hydraulics jerky on Deere 4610

    From the gearbox to the pump....thick pipe with rubber hoses and clamps ....check them !
  4. Replies
    10
    Views
    774

    Re: John Deere 2950 hyd issue

    472953
  5. Replies
    10
    Views
    774

    Re: John Deere 2950 hyd issue

    Check low pressure here
  6. Replies
    13
    Views
    1,235

    Re: Slip Clutch maintenance.

    Hopefully it was adj correctly.. messeure springlenth and nota it . Then strip the slipclutchassy and remove all rust an loosen all discs . Reassy all and readjust to ariginal springlenth
  7. Replies
    4
    Views
    803

    Re: Case 2090 enginereplacement

    OK !
    What other engines will fitt in the Case 2090 ?
    Mybe a Case W20 ?
    Or a Case 2290 ?
  8. Replies
    4
    Views
    803

    Case 2090 enginereplacement

    My dad bouht a Case 2090 with the BD504 engine in it . It throw a bigend bearing 4 years ago. We had to replace the crankshaft.
    Now we stand at that crossroad again !
    Will a Cummings engine fit?...
  9. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    Oilflow as on tractor
  10. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    471954
  11. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    471953
  12. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    471952
  13. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    Oilflowchart
  14. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    471950
  15. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    Testports for testing transmitionpump pressure..front one ...rear one is oilpressure going to the mainpump...see if there is any pressure ?
  16. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    471949
  17. Replies
    19
    Views
    1,495

    Re: Single Action Cylinder Problems

    And after flowering putting the cv in float .

    Sent from my B15Q using TractorByNet mobile app
  18. Re: Older Mahindra 485 Transmission Jammed?

    When removing gearshiftcover take note to Mark all inside before loosening shifterforks...even thoses thin plates !
  19. Replies
    19
    Views
    1,495

    Re: Single Action Cylinder Problems

    Returnoil is never under pressure !
    If your ancker point let the wing go oversenter it can not go down by itself !
    Rearrange your anckerpoint or make your sil dubbleacting !
  20. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    Are you turning the shaft a little for and back ? Looks like it !Uncopple thick steelpipe and see if oil come uit when you start the engine ? Looks like no supply to mainpump . Test at testports in...
  21. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    Green RING = ( NR.18 )GASKET = ( NR.19 )
  22. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    windshield sealer. is ok between casing and plate but between plate and MCV IS CRITICAL TO USE GREEN SEAL AND REINFORSD GASKET
  23. Replies
    10
    Views
    1,387

    Re: Case 2150 orchard

    [QUOTE=DLTTrekkers;4473695]The needlebearing inside the reversegear packed up ..replaced it with a fosphorbronze bush is the answer . That gear is the first one ...topshaft ad you remove the...
  24. Replies
    10
    Views
    1,387

    Re: Case 2150 orchard

    The needlebearing inside the reversegear packed up ..replaced it with a fosphorbronze bush is the answer . That gear is the first one ...propshaft as you remove the shiftcover .
  25. Replies
    10
    Views
    1,190

    Re: John Deere 2440 No PTO

    The pack with all the plates and fireplaces ?
  26. Replies
    10
    Views
    1,190

    Re: John Deere 2440 No PTO

    So it was a dualclutch ?
  27. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    12 is return oil from steering
    3 and 4 to and from hitch
    5 to pto pack
    11 supply from pump
    13 supply to steering
    2 pilot relief valve
    1 priority flow divider
  28. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    471313471314471315
  29. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    If all do not help... drain oil and remove hydraulic filter and then MCV and then remove pump from MCV taking care to check o-rings. Then split plate from MCV and inspect gasket (should be a...
  30. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    471220471221471222471223
  31. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    471217471218471219
  32. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    All should work at idle asswell . Check iff priority valve is stuck? Must be free ! Pilot pressure valve is sealed in casing with a o-ring . Check iff that o-ring is in its place ? Pilot pressure...
  33. Replies
    11
    Views
    1,367

    Re: IH 434 gears grinding when shifting

    Oilleak under Tractor ?
    Engineoil or gearbox oil ?
  34. Replies
    10
    Views
    1,387

    Re: Case 2150 orchard

    And the f/r selector fork broke allso
  35. Replies
    10
    Views
    1,387

    Re: Case 2150 orchard

    In my 2140 the f/r link going into the box had slop in it and the f/r sincro s lining material came loose. The needle bearing in the reverse gear broke allso. Nou for the repairs .
  36. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    As you sit on tractor the dipstick is at your leftfeet
  37. Replies
    10
    Views
    1,387

    Re: Case 2150 orchard

    Then it has a SLH DEUTZ-FAHR Engine in it with a MITA hydraulic cover and a Cararo back-end with a Cararo 404 axle infront. Tomorrow I am going to temove a gearbox from one .....its stuck in reverse...
  38. Replies
    10
    Views
    1,387

    Re: Case 2150 orchard

    Look on r-side of engine ...engine numbre starts with 1000A ...? ...Aircooled......Cararo backend ?....Gearlevers on side of seat ?
  39. Replies
    10
    Views
    1,190

    Re: John Deere 2440 No PTO

    Remove gearshiftcover...remove plug infront of shiftcover...remove valve and replace c-clip...take care not to strip valve...replace and test !
  40. Replies
    6
    Views
    1,096

    Re: Simms Pump and Fordson Diesel Major

    Check if butterfly is still mounted to that throttleshaft ?
  41. Replies
    41
    Views
    3,801

    Re: Another JD 2155 Hydro Thread

    Check mainpumpcoupler and key on mainpumpshaft ....then priorityvalve...remove and clean !
  42. Replies
    10
    Views
    1,190

    Re: John Deere 2440 No PTO

    Remove PTO engage lever between the gearlevers and check inside if the very small c-clip is still in its place ? To repair ...gearshiftcover must come off .
  43. Replies
    6
    Views
    1,096

    Re: Simms Pump and Fordson Diesel Major

    Why do I remember something about a tube running from the pump to the intake manifold and the throttle link attaches to a butterfly in the intakemanifold ?
    Check tube and butterfly !
  44. Replies
    5
    Views
    728

    Re: brake adjustment 1983 2110

    What make ?
  45. Re: Older Mahindra 485 Transmission Jammed?

    Remove gearlever then get all gates in a row and put gearlever back . Locking will happen again.
    To repair it those Springs needs replacing
  46. Re: Older Mahindra 485 Transmission Jammed?

    A little loose ? Detentsprings in softcover broke ! Next step is gears that lock (going in gear that should stay where they are)
  47. Replies
    6
    Views
    1,096

    Re: Simms Pump and Fordson Diesel Major

    Is there oil in the pump ? Is the rack free ? Or binding ?
  48. Replies
    13
    Views
    1,427

    Re: 4010 steering cylinder stripped!

    Do not loctite or weld on it ! That thread is still good to hold a lifetime !
  49. Replies
    2
    Views
    941

    Re: Case IH 495

    Bigbody but small engine tractor...do not overdo FEL work...replace hydraulic filter with every service and check for fillings in gearboxoil and filter.
    Brakemastersilinders work with hydraulicoil...
  50. Thread: FEL issues

    by DLTTrekkers
    Replies
    9
    Views
    1,112

    Re: FEL issues

    Wet brakes ? Remove and check brakeparts ! Then replace pump !
  51. Replies
    3
    Views
    800

    Re: Hydraulic oil for B275 International

    Hydraulic oil in the 3point and 80w90 in the gearbox/diff/finaldrives
  52. Re: McCormick International B275 Hard too start

    You need to check if your glowplugs are connected up correctly
    1. connect 1and 2 and then 3 and 4 (with big eyes on connecting wire)
    2. Then 2 and 3 ( small eye wire)
    3. Last power supply on 4 (...
  53. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    When priority valve is stuck the steering will work ok at lou rpm s and good at hi rpm s but allels will not work well. So ....check priority valve first.
  54. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    468933468934

    Sent from my B15Q using TractorByNet mobile app
  55. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    Yes

    Sent from my B15Q using TractorByNet mobile app
  56. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    468916468917468918468919
  57. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    Under the hydraulic filter is a valvebank called the mcv (multpil controller valve ) and it you lay under the Tractor you will see a few plugs going in it from the bottom . Remove the front plug and...
  58. Replies
    25
    Views
    2,631

    Re: case 485 - little to no hydraulics

    Replace hydraulic filter and clean screenfilter .Their togather .Then check priority valve ...might be stuck in open position . If stuck...remove plug and spring.....put a bucket under and start and...
  59. Replies
    5
    Views
    747

    Re: Sticky scv?

    Mountingplate should be a thin plate that will bend to the form of the controlvalve and not the otherway round

    Sent from my B15Q using TractorByNet mobile app
  60. Replies
    5
    Views
    747

    Re: Sticky scv?

    keep one tight and the other's change nuts with nylocknuts . Do not tighern them .

    Sent from my B15Q using TractorByNet mobile app
  61. Replies
    5
    Views
    747

    Re: Sticky scv?

    Valve mountingplate cauze valve to bind ....loosen all but 1 bolt and check again
  62. Thread: Fiat 350 S

    by DLTTrekkers
    Replies
    3
    Views
    1,060

    Re: Fiat 350 S

    Found a starter and made it to fitt !
  63. Thread: Fiat 350 S

    by DLTTrekkers
    Replies
    3
    Views
    1,060

    Re: Fiat 350 S

    Atlast !
  64. Replies
    14
    Views
    2,433

    Re: Ran dry, won't prime/bleed

    Weld one side as long as there is still space for the enginecrackplay.
  65. Replies
    14
    Views
    2,433

    Re: Ran dry, won't prime/bleed

    Mybe pumpconnectordrive stripped ?
  66. Replies
    14
    Views
    2,433

    Re: Ran dry, won't prime/bleed

    Air in suction line...check all connections before the pump !
  67. Thread: Fiat 350 S

    by DLTTrekkers
    Replies
    3
    Views
    1,060

    Re: Fiat 350 S

    467780
  68. Thread: Fiat 350 S

    by DLTTrekkers
    Replies
    3
    Views
    1,060

    Fiat 350 S

    I am looking for a starter for this tractor. Some idiot lost it about 3 years ago !
  69. Replies
    6
    Views
    1,363

    Re: Sealing top flange of wet sleeve?

    As in the Lamborgini workshopmanual
  70. Replies
    6
    Views
    1,363

    Re: Sealing top flange of wet sleeve?

    467779
  71. Re: Timing marks for fuel pump timing - Which ones?

    Page starts with no 5 .......where is no 1....to....no 4 ? That will be the prep for this proceedure !
  72. Re: Kohler cv22 keeps breaking rocker arms after rebuild

    Valveguides to long ?
  73. Thread: Fiat 350 S

    by DLTTrekkers
    Replies
    3
    Views
    764

    Re: Fiat 350 S

    467553
  74. Thread: Fiat 350 S

    by DLTTrekkers
    Replies
    3
    Views
    764

    Re: Fiat 350 S

    Starter was lost by some idiot !
  75. Thread: Fiat 350 S

    by DLTTrekkers
    Replies
    3
    Views
    764

    Fiat 350 S

    I am looking for a starter for this tractor and it must be in South Africa
  76. Replies
    3
    Views
    642

    Re: JD 1140 Alternator Alignment

    If possible..... move the alt pulley...dose the belt fit in the new alt pulley ? Mybe you will have to widen the pulley ?
  77. Replies
    7
    Views
    1,194

    Re: Stripped PTO yolk

    First strip the crossbearing
    Messure the cupsize and note down
    Now messure the distance from cup to cup over the crossbearing and note
    Now phone your supplier and ask for a 6 spline yoke and give...
  78. Replies
    3
    Views
    749

    Re: Hydraulic squeel under heavy load

    Beltdriven..........Whats the shape of the pulley ?New pulley = v shape.........old pulley = u shape.........u shape no driving !
  79. Re: 231 Massey Oil leak from tachometer weep hole

    Bad job......redo !
  80. Buying Advice Re: Live PTO vs. Over-running Clutch vs. Slip Clutch

    Flywheel effect..........have you see a tractor running into your car and the operator can not stop the tractor intime ? That is without a ORC !
  81. Re: If you have a 5000 series Deere and it cranks but won't start, try this first.

    Regional thing ......I got it here aswell on a JD 5320
  82. Re: Shuttle Drive Massey 40E with front loader

    Mybe engine revs set to high for idle .....idle should be +-650rpm
  83. Replies
    15
    Views
    2,031

    Re: Siromer 204s starting problem

    Mybe your ext hyrauliclever is in detend and pump the oil (deadend) ....no pipes fitted at the back ?
  84. Replies
    14
    Views
    2,626

    Oil & Fuel Re: John Deere 2640 Will Not Start

    I totaly agree
  85. Replies
    14
    Views
    2,626

    Oil & Fuel Re: John Deere 2640 Will Not Start

    If inj pump is worn you wil get flow when loosening the inj pipe but no flow when inj is connected !
  86. Replies
    14
    Views
    2,626

    Oil & Fuel Re: John Deere 2640 Will Not Start

    Remove one injector out of sil head and attach it again outside to the inj line ......crank the engine and see if fuel is spayed out DO NOT COME NEAR THAT SPRAY......VERY DANGEROUS......if no spray...
  87. Re: Long D124 3 cyl diesel engine missing problem

    Good for you !
  88. Replies
    2
    Views
    591

    Re: Hydraulic gear pump advice

    Hallo new pump.......do not wast time on old pump or replacing seals in old pump
  89. Replies
    11
    Views
    1,732

    Re: Finally Happened

    Ho ho ho ! No work ....no mistakes !
  90. Replies
    3
    Views
    690

    Re: MF 135 hydraulics

    Some internal adjustments I belief wil do the trick .
    Is there a lot of play on the toplink connectingpoint ?
  91. Re: Zetor 5340 (John Deere 2200) Diesel in Engine Oil - Please help!

    removed the hydraulic pump again and found the new front seal had a split and was blown out
    You did try that.......Now to replace the hydro pump ! Do not adjust the pressure !
  92. Re: Water is coming out of my exhaust on my JD 2010

    Hallo sleevedeck or both deckgasket and/or topgasket
  93. Replies
    4
    Views
    1,278

    Re: TD95D - Hard Clutch Pedal

    In general.....check the angle where the cable and the releaselever come together......if angle is bigger than 90degrees its bad......if smaller than 90 degrees its ok
  94. Re: International 674 hydraulics and brakes

    Check very small filter in flex supply pipe to keepfill reservoir . If you remove that pipe you wil feel a little hard piece in the pipe ....thats that little filtre!
  95. Replies
    1
    Views
    473

    Re: International 464 steering issues

    Steeringvalve faulty or out of timing
  96. Re: Zetor 5340 (John Deere 2200) Diesel in Engine Oil - Please help!

    fIRST......where dose fuel and oil meets?
    1. Inj pumpseal
    2.Transferpump diaframe
    3.Leaky injectors
    4.Glowplug also called the Termostart PLEASE GOOGLE thermostart
  97. Re: Zetor 5340 (John Deere 2200) Diesel in Engine Oil - Please help!

    Glowplug......thermostart valve ?
  98. Replies
    28
    Views
    4,616

    Re: Need help fixing my tractor

    Pedalfreetravel ?
  99. Replies
    1
    Views
    533

    Re: Massey Ferguson 230

    Its a orbirrolvalve under the steeringwheel . If there is a oilleak that valve needs to be repaired/replaced !
  100. Replies
    3
    Views
    686

    Re: Perkins ad3 152 valve seals

    No seals
    Make sure that your breather is open
Results 1 to 100 of 467
Page 1 of 5 1 2 3 4
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.