Tractor../> Smoke came out and I saw two blue wires making ground
Type: Posts; User: fxrs55; Keyword(s):
Tractor../> Smoke came out and I saw two blue wires making ground
I think I read somewhere on this forum that the small pump
on this type of tractor is inadequate to operate a front end loader.
Are you using an overrunning clutch on the pto? If so, maybe its whats worn out and slipping.
How about a picture of your setup?
You could try the link below. They are in Italy.
Here is a link to the rebuild of my TX1300f/Bolens G154 if you want to look at pictures.
You are going to have to remove that brake rod. Its not letting the brake
shoes to fully retract and I think the shoes are hanging up in
the brake drum. Here are a few pictures of the drum and the...
Here is the page from the manual.
Check the engine oil level. Is engine sucking the oil out of the crankcase ?
Hello I was looking at the picture and that looks like a turkey, and the tractor looks good also.
check the links below for some rops for your tractor.
I see you have the front PTO thats nice. What do you have hooked up to it
in the picture of tractor towing the trailer?
Also is the PT-425 4 wheel drive? I'll bet your neighbors think it looks...
I never heard of a power trac before so I googled it
and that looks like an interesting machine. How about
a few pictures?
Nice, Glade it was easy. Thanks for the picture. Its nice to
see what is wrong with other peoples tractor for
Here is a link to the thread I made about the rebuild of my train wreck G154.
If you have trouble sleeping read some of this, It will put you right to sleep.
Glad it was an easy fix. I have a G154/TX1300F and the spline boss
in mine was shot and the input shaft in the transmission was almost
shot. I welded each spline on the shaft and then hand filed...
Hello, I have a G154 also. Mine has a Mitsubishi KE70 engine and
I have been able to by engine parts at the link below.
They are very nice and helpful people.
Small Import Tractor Supply - Home...
It might be easier to just switch the engine. If you do the axle swap you'll need
to swap transmissions also because you will also need the output shaft
from transmission to front diff as well as...
What do you mean it won't work? The tractor won't go or the
clutch will not disengage? If it won't disengage then clutch disk might be
rusted to flywheel. If its rusted you could remove the rubber...
So when you push the lever down to engage the front wheels or the 4x4 the front wheels do not get any power from the transmission? Do you have the service manual for this tractor? I have the manual...
Ops, I just noticed you are in Antwerp, Belgium so I don't know
what a domestic model would be there.
Check this link for parts.
Check this link, Domestic model seems to be Massey Ferguson.
I have been able to get parts for my TX1300F / Bolens G154 at a Massey dealer.
TractorData.com Massey Ferguson 1205 tractor information
If you have the manuals it should tell you that the bevel case takes 23.36 oz
and the gear case takes 8.32 oz.
What make and model of tractor are we talking about
Back in October I changed the transmission/hydraulic oil. I was using
Xtreme oil I bought at Tractor Supply. I didn't think it was
working all that well. So I bought a 5 gal bucket of Mobil 424...
I have a 16 lb cap on my G154. It has been on there since I rebuilt
the tractor. I have not had any issues with over heating or
leaks or coolant loss. It is a stant part number 331.
What part of...
Do you have two hydraulic levers on the fender?
Here is a link to used parts.
Iseki TU1700 Dismantled Tractors for Sale | Fastline
The clutch pedal pivots on the shaft that goes to the left brake pedal.
This shaft crosses from the right side of tractor where the brake pedals
are to the left side to connect to the left brake....
here is one
Bolens Iseki G152 H1502 Tractor Complete Front Mounted PTO and Actuator Lever | eBay
Hello, Here is a part number filter 1427-503-0060-0.
or Massey Ferguson 3754534M1
check this site
Search results for: '3 point-hitch links parts'
Here is another site that is in...
does the noise stop when tractor comes to a stop? what happens if you kick it into
neutral while still moving and then not depressing the clutch and coming to a stop?
Here is a link to the rebuild of a tx1300f that was given to me.
I have a little over $1100 dollars fixing everything. If you already
have a working 4x4 tractor then I would take the loader off
I sprayed everything with simple green and let it soak about 10 mins
then I pressure washed everything. I did not sandblast the tractor as a whole.
I did sandblast a few small parts but I'm not...
When you had the pump apart did you replace the shaft seal?
Also maybe the spring on the relief valve is weak and when hot
its not holding valve closed. I have had the pump shaft seal
go bad on my...
I was using the bolens/iseki most of the day today. It is running good.
I was using the tractor to pull a tarp that I was pushing leaves on.
I was mulching the leaves with my cub cadet and then I...
Hello olom, are you using SAE 80 oil for your transmission/hydraulics? Thanks.
I don't have a picture handy but I have looked at attachments
for my G154 and one of the pictures of a snow blower attachment
was lifted with the 3 point. It had a pivot point in the
Does yours have the KE70 engine. I was just looking at your
picture an your oil pan is right up to the cross member.
Also I noticed that tie rod but one thing at a time.
Do you have a picture of the front of your tractor?
Hey Dan, I just went out to the garage to look at mine
and I must say mine is different than yours.
Here is a picture of mine. Mine has much more
clearance than yours.
I have the same tractor as you and I was able to remove
the 2 next to the pivot with an open end wrench.
The others I had a swivel joint on my socket.
I did not replace the rod bearings. They looked fine.
I was given my TX and it had sat unused 10 to 15 years.
My friends neighbor bought it at an estate sale.
Apparently the neighbor could only...
If there is coking on the sides of the cylinder walls that the rings
are not cleaning off, Maybe the rings are stuck in the grooves
on the pistons. This could be why rings are not keeping
Here are a few pictures of my head before repair.
I put the head on its side and poured kerosene
in the exhaust ports and the intake ports.
You can see in the pictures the exhaust valves
Don't get me started. Another thing *&&&^*%#%^!#$!#
and also !!@#$^&%^*&*. Good luck.
Oh, If you do the rings there were two
different types used. One had flat sides
and the other ones were shaped like
a key stone. It depends on the year of
Oh make sure you get the head gasket for the
KE70 engine and now the KE75. The KE75 engine
has larger bores and the holes in the head gasket
are bigger also. I think that happened to another...
I read that part when I did mine and though ok the head gasket
has sealant on it. I bought a new head gasket from the internet.
I found a web site selling the gasket for $59 us and I was just...
Here is a link to the thread I made about my
journey fixing my TX1300F.
Oh, On this side of the pond a new head gasket is $140 us.
If I were you I would drop the pan and remove the pistons
just to clean and inspect the rings.
Can you rock the pistons back and forth a little in the bores?
Take a screw driver and put a little pressure down and then
see if you can move the pistons side to side. If the rings
are stuck you...
Hey Dan, you can remove the oil pan without removing the
front drive shaft. Here a few pictures from the repair manual.
I can E-Mail you the manual in pdf format.
If that tractor has the 4 wheel drive lever and you say
it has a front drive output shaft coming out of the front
of the transmission then I believe at one time that was
a 4 wheel drive tractor. I...
When I got mine it had no compression in the front cylinder
and less than a 100 in the rear. After I disassembled the
engine enough to remove the pistons I found that
the rings were stuck from...
Looks like a TS series, not sure of which TS.
Check the link below. Just click on any of the
TS models to view pictures.
TractorData.com - Iseki tractors sorted by power
Here is a link to a thread I made about my
easy repair of my G154 / TX1300F
How far are you opening the throttle? Try opening it
over half way or more and if it does start quickly
move throttle down but if you go to idle it may
stall if its really cold outside. When I...
Well the first thing you can do is post some pictures
here so we can see what it looks like. A picture
is worth a thousand words.
Is that it in the picture with the front end loader?
Why do you think the 4 wheel doesn't engage?
Did the people you bought it from tell you
anything about the tractor and problems it has?
can you buy from this place
Vendita trattorini giapponesi Piemonte, trattorini giapponesi Cuneo, trattori Kubota Piemonte, trattorini Iseki...
Check this link.
1988 WHITE FIELD BOSS 37 Tractors | ALMA TRACTOR & EQUIPMENT ALMA, AR #C555
Lets start from the top. Do you that you turn the key on, then you turn the starter
knob counter clockwise to warm the glow plugs until the indicator on the left
side of the dash glows red? then...
The one next to it is a 1967 Pennsylvania Panzer. They came from the factory
painted tantalizing turquoise. I need to finish painting mine.
Here is a link to my work sofar on that tractor.
Time for an update. Its been around a year since I more
or less finished the Bolens. I have used it over the summer
to regrade my driveway and the in laws driveway.
I have used it with the dirt...
I would say that hood lable clearly shows its a TL model. I made my guess on just the picture.
that looks like a TE model. parts manual at like below
Here is a link to a manual for a ts1910 which is close.
Here is another part of the head gasket video.
Here is another video of the head gasket replacement. This one is of the water pump.
Did you check the fluid level in the transmission?
One area water can get in transmission is around the rubber boot
that covers the shifter where it goes into the transmission.
I finished rebuilding the hydraulic cylinder and reassembled
everything back onto the tractor. After bleeding the air
out of the cylinder I could not believe how much
better the 3 point lifts the...
Here is a parts manual for a TS1910
I finally have a little time to address the weak 3 point hydraulics
when lifting stuff with my dirt scoop. Upon disassembly I found
the o-rings are shot and the piston has galling as does the...
Nice, but how about a picture of the construction site.
The hardened washers are not attached to the head bolts so when you
remove the head bolts the washers are left laying on the head.
They could fall into the push rod openings and land on the...
I have been using the tractor with the dirt scoop and I think
I need to replace the O-rings on the 3 point lift piston.
I have to give it a good bit of throttle to lift scoop with
dirt or stone in...
The PTO is a three speed. Push the lever all the way down is first.
pull up one click and that is second. Pull up another click
is neutral. All the way up is third. Here is a chart with
looks like a good one.
Look at that chart again. Check the section for standard nuts and bolts.
the bolts that hold the rocker arm assembly to the head are 12mm.
12mm bolts have a torque of 25 foot lbs.
Here are the torque specs.
Go to this link for the user manual and parts manuals.
The link below is my bolens G154 which is the same as a TX1300F. I have links to...
Also some pictures of yours would be nice.
Is your tractor a TX1300 or TX1300F ?
Go to this link for the user manual and parts manuals.
The link below is my bolens G154 which is the same...
Does it sound like the one in this video?
Go to this link and then view parts books as guest
and then browse books to the left of page then click white then click tractors
then click agricultural wheeled then click 2-30 / 2-35 field boss....
I finished replacing the head gasket and water pump last week and so far so good. My laptop
is down and all of my pictures are on it. I need to replace the power jack on the mother board.
check this site. It has manuals for TS1910
I was using the tractor a good bit on Sunday and the water pump
is starting to leak more and it also now has a rumble sound.
Time to replace the pump and to replace the head gasket.
Here are a few...
I sanded the heck out of the frame and outside of the scoop to remove
the rust. I looked at different types of rust sealer / paint and I
just did not want to spend as much money for paint and...
The four wheel drive model does not have a fitting. It does not get lubed.
check the pictures below.
Yes it does lift it and with me standing in it. I weigh around 180 lbs.
Well it rained all day so I worked on the scoop in the garage
and here are a few pictures. I took it apart to scrape off
some of the rust and fix the latch and some loose bolts.
Back on the topic, When are you buying a Kawasaki Mule on tracks?
I believe every person anywhere in the world has some interesting stories of things
from or about their life. If we take the time to listen we all have a story or two
of interest. I have had people...
I bought a dirt scoop on Saturday and it was poring rain as
we loaded it into my mini van. We loaded it with a fork truck.
I was able to drag it onto the bumper and back my tractor
up to it and...
Well I don't feel comfortable typing my thoughts with a retired English teacher.
I hope you don't grade my work over the internet for everyone else to
see how I butcher the English language. Anyway...
here are a few more pictures of the hitch. I picked up
an 1 1/4" receiver tube that I will weld inside of the
upper and lower plates.
Ok, I'm curious. If I may ask why do you have visitors from around the world?
And do you tap maple trees to actually make maple syrup?
Have you tried the link below?
Tractor Salvage Dixon, IL - Sheaffer's Town & Country Tractor
I received a few things in the mail today.
The weeping head gasket has been bugging me
and the water pump is leaking and the shaft
in the water pump is getting very loose and
with my luck just...
here is another video to sleep by. Its of the machining of the trailer hitch.
After I'm satisfied with the fit I will then weld all of the parts together.
Here are a few pictures of the hitch I am making.
This is now made from cold rolled steel.
I think I'll use the one I made from wood for a napkin holder.
I'll give it to my wife for mothers day....