Search:

Type: Posts; User: SSdoxie; Keyword(s):

Results 1 to 100 of 2446
Page 1 of 25 1 2 3 4

Search: Search took 0.06 seconds.

  1. Re: Did Bobcat make a gas powered mini backhoe ?

    No it was not Terramite, it was Earthforce made in Chech Republic. Bobcat only had this backhoe line for about 4 years, the purchase was primarily to obtain the manufacturing facility to expand in...
  2. Replies
    2
    Views
    167

    Re: Bobcat 463 cooling system question.

    First - Welcome the TBN.
    The 463 is a skid-steer loader considered construction equipment so this is correct place to post the question.

    From what you are describing - gauge in-op but wires and...
  3. Re: Did Bobcat make a gas powered mini backhoe ?

    Bobcat did have a line of smaller tractor backhoes similar to the Termite. The smallest was B200, all were Kubota diesel powered no gas version. If it is one of these the starting issue may be...
  4. Re: Did Bobcat make a gas powered mini backhoe ?

    No idea what the first model was, that was long before my time with the company. I do know Bobcat started out in mini-excavator business purchasing machines from Komatsu. At that time the 231 was...
  5. Re: Did Bobcat make a gas powered mini backhoe ?

    They never made one that I'm aware of and I retired last year after 18 years with Bobcat.
  6. Replies
    14
    Views
    1,391

    Re: hard starting CT235

    That rough running for a short time when first started with engine cold is normal especially if started before the glow pug light goes out, or if glow plugs are weak/faulty. This tractor has...
  7. Replies
    9
    Views
    5,333

    Re: Bobcat 743B Left Reverse Drive Problem

    It could be something sticky or catching in relief/replenishing check valve but it sounds more like steering linkage is loose. Check all rubber bushings and especially the arm that clamps on to the...
  8. Replies
    12
    Views
    2,509

    Re: CT235 won't start. Fuel solenoid won't engage

    Kioti and Bobcat will be the same parts for the solenoid. Buy them from Kioti
  9. Replies
    11
    Views
    821

    Re: What size battery for CK30 HSt?

    I just replaced mine 2 days ago, installed a 24F 700 CCA. The F places the terminals forward of the air filter housing so next time recharging is needed it will be easier access. Any sixe you use...
  10. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    You have it correct Dave. As an installation precaution, rig up a Tee and pressure gauge so you can check free flowing pressure through the Backhoe valve when the A or B port is activated. Test it...
  11. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    The relief valve for the hydraulic circuit (loader, rear auxiliary, & 3 point) is at the inlet port of the loader valve. Flow of oil goes from pump to loader to rear aux, to 3 pt. so the loader...
  12. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    The pressure relief in the loader valve would open in this case to momentarily protect the pump and the engine will RPM will decrease. This would be no different than going to a dirt pile with the...
  13. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    VONBERG VALVES INLINE CHECK VALVE 19139-.188

    Here is a simple inline check valve for Surplus Center. Shipping will likely be more than the valve @ $8.95.
  14. Replies
    2
    Views
    829

    Re: 853 engine knocking ,loud.

    The 853 has an Isuzu 4JB1 engine. This same engine model with different oil pan, intake & exhaust manifolds, and flywheel
    was also used in Mustang skid-loader model 960 & 2060 (2060 is turbo...
  15. Replies
    8
    Views
    10,316

    Re: Trick to unlocking the traction lock?

    This question was posted in 2010 so hopefully he figured it out.
    For anyone coming across this with same issue, check your Park Brake switch. If Park Brake is "ON" or switch is faulty the...
  16. Replies
    2
    Views
    554

    Re: Bobcat 553 magnetic seat switch.

    Bobcat sells a kit to replace the seat switch with a Push to Operate button system so is same as current production loaders. It has a different control box at rear of cab and the Traction Lock...
  17. Thread: new to me 863

    by SSdoxie
    Replies
    3
    Views
    1,255

    Re: new to me 863

    Dealers replace the belt without pulling engine. There are special tools required. Need locator pins to position crank & camshaft at TDC then lock them in place to prevent turning and also requires...
  18. Thread: Fan Belt

    by SSdoxie
    Replies
    5
    Views
    1,517

    Re: Fan Belt

    Check the alternator mounts. Make sure both top and bottom are tight, no cracks in the mount, and the pulley is aligned correctly with the crank and water pump pulleys.
  19. Thread: new to me 863

    by SSdoxie
    Replies
    3
    Views
    1,255

    Re: new to me 863

    The G series is newer version of 863. G series came out in 2000 and was last version made. The electronics are totally different in G to F series.
    I would not use Universal Tractor fluid in it. An...
  20. Re: Bobcat 963 "C Series" Fuel Pickup Tube Location

    Fittings will be somewhere in the front portion of main/primary tank = look in between engine and hydro pump assembly. The 800 series have the belt drive on left hand side so fuel tank fittings are...
  21. Re: Limited slip differential versus Hydrostatic traction control (HTC)

    Mountaineer, Dealer is correct. Any 5610 that has the required cab & mainframe harness, axle shafts to accept the added speed sensor came with HTC as standard equipment, it was/is option for 5600. ...
  22. Replies
    10
    Views
    2,120

    Re: Bobcat 753c overfull chain case

    Thumb switch on right handle is for momentary hydraulics to front couplers is bi-directional. Typically used for cylinder operations. The trigger switch on right handle is for constant flow (detent)...
  23. Replies
    10
    Views
    2,120

    Re: Bobcat 753c overfull chain case

    Look for another one of these for the other motor. Bobcat did change sometimes with different series production, but most 753s had 2 filters - 1 for each motor.
  24. Replies
    10
    Views
    2,120

    Re: Bobcat 753c overfull chain case

    Case drain filter is a small metal canister in-line with the hose. Follow the smaller of 3 hoses going to the drive motor is the case drain, follow that hose back from each motor until you find it. ...
  25. Replies
    10
    Views
    2,120

    Re: Bobcat 753c overfull chain case

    Not necessarily the drive motor seals bad, could be, but fluid is going past the motor carrier seal. The carrier is the assembly that bolts to the chain case frame and has shaft that has splines on...
  26. Replies
    5
    Views
    1,019

    Re: Bobcat 331D no start

    Is there any smoke from exhaust when cranking? If there is smoke, it is getting fuel but firing - 1st thought would be check glow plug/preheat circuit.

    No smoke is no fuel delivery - check fuel...
  27. Replies
    109
    Views
    15,607

    Re: Bad day,Lost an engine

    Load or power to the drive train varies depending on resistance to wheel rotation. At full maximum, stall point, the additional HP combined with slightly higher relief means more torque available to...
  28. Replies
    109
    Views
    15,607

    Re: Bad day,Lost an engine

    Same drivetrain (other than HST in 235) is used on all 3 models. Done for simplicity/commonality of parts for manufacturing.
  29. Replies
    109
    Views
    15,607

    Re: Bad day,Lost an engine

    The 235 engine will fit right in without modifications or other required parts. Part number of the 235 HST is different but that is only because of design of internal directional check valve and...
  30. Replies
    18
    Views
    3,971

    Backhoe Re: Woods subframe to CT230

    The rear mounts of sub-frame will be the same as CK30. The question will be how the front mounts are installed/located. If mounted to the transmission case, flywheel housing, or engine then it...
  31. Replies
    12
    Views
    3,568

    Re: What model of toolcat do I have?

    The front boom design did start with the C-series however Independent Suspension stated with the D-series. With Independent suspension and a Kubota engine it is either a D or F series. First 4...
  32. Thread: Coolant in Oil

    by SSdoxie
    Replies
    19
    Views
    3,012

    Re: Coolant in Oil

    Does this have an engine oil cooler, oil cooled by radiator coolant? If so that would be a place to check. Exchanger rust through and push anti-freeze into oil.
  33. Replies
    6
    Views
    1,927

    Re: 773G turbo B.I.C.S. messing up

    Another possibility I just thought of, although less likely because you say the Traction Lock Override seems to work fine, is loose ground from the controller. Easy enough to check as all the...
  34. Replies
    6
    Views
    1,927

    Re: 773G turbo B.I.C.S. messing up

    For unknown reason the controller is reading the seat bar is being raised/moved out of normal operating position. Three checks to do before at the sensor and/or circuit: 1. Turn key (power up the...
  35. Replies
    20
    Views
    4,276

    Re: Bobcat 753 Arm Lift Problems

    I don't have any good advice on getting this out. The piston does need to be kept square with the barrel as it comes out so it is sliding only on the seal. Coat hanger likely has too much flex to...
  36. Replies
    6
    Views
    1,927

    Re: 773G turbo B.I.C.S. messing up

    With both brakes and loader locking indicates problem in sensor circuit. Could be loose connection in feedback or ground circuits. The seat bar sensor and Press To Operate Button are signal input...
  37. Replies
    6
    Views
    1,927

    Re: 773G turbo B.I.C.S. messing up

    Do the brakes lock up along with the loader control or just loader functions?
  38. Replies
    20
    Views
    4,276

    Re: Bobcat 753 Arm Lift Problems

    Glad you found the lift problem. That rod should be salvageable, clean up end of the threads. I don't see any evidence of Loctite on the rod threads. Red (hi-temp) Loctite is called for in service...
  39. Replies
    20
    Views
    4,276

    Re: Bobcat 753 Arm Lift Problems

    "Tilt and Aux work fine"- indicates supply from pump to control valve is OK. All 3 spools receive flow pump through same line. The load checks I mentioned are internal in the valve, look for 3 hex...
  40. Replies
    25
    Views
    4,404

    Re: Full service - How hard is it to do really?

    No special tricks to this. Remember to drain both oil pan plugs, all 3 hydraulic drains (main plug plus 1 at each axle housing) and do NOT over tighten plugs when reinstalling. Filters aren't too...
  41. Replies
    20
    Views
    4,276

    Re: Bobcat 753 Arm Lift Problems

    I think you may have 2 issues going on, milky fluid and loss of lift. Contaminated/milky fluid should affect all functions not just 1 and I don't see anyway contaminated fluid would allow the lift...
  42. Replies
    74
    Views
    5,875

    Re: How's your hand strength.

    Pair of channel locks and rubber strap wrench for bigger bottles have been normal tools is kitchen drawer for years. Started out Better Half needed them now I do. It couldn't be do to age or...
  43. Replies
    8
    Views
    6,250

    Re: Traction Control

    This is a serial number break in F models, later production can be retrofit with this but earlier production cannot. Kit is not cheap. It requires additional wheel speed sensors, new brake control...
  44. Replies
    20
    Views
    4,276

    Re: Bobcat 753 Arm Lift Problems

    Foamy oil could be water or air. Given the explanation of recent fluid change and leak repairs I think air is more likely. Air entry would be would be somewhere on the non-pressurized side of...
  45. Replies
    20
    Views
    4,276

    Re: Bobcat 753 Arm Lift Problems

    Your description sounds like lift function is going into position when spool is moved even tough lift up control is opposite direction of float. You mentioned actuators so I presume this is either...
  46. Re: question on a frame to bring the rear PTO to the front of tractor?

    I just typed "Rear to Front PTO conversion" in google and came up with this one. Lorenz Front Mount Kits
  47. Replies
    8
    Views
    6,250

    Re: Traction Control

    Traction control is basically same as using independent brakes on a tractor. Difference is there is only 1 brake pedal like in a truck, so using wheel speed sensors the controller notes when a wheel...
  48. Replies
    7
    Views
    2,574

    Re: Where to buy a 7TL FEL?

    The 7TL is only Bobcat model that will fit. The Kioti loader for at CK 30 will fit right up, has same frame. Most all CT230s came with the loader joystick installed so only hydraulic connections...
  49. Replies
    416
    Views
    144,449

    Re: If you have Toolcat questions, ask them here...

    Question should have been posted in Bobcat Construction Equipment Forum not Toolcat. To answer question, yes. If start engine and push the Press to Operate Button with seat bar up the brakes will...
  50. Re: Toolcat series A - please help with fuel line question

    Not sure, but looks like injector should be rotated 180 so return line rubber hose is located at 4 o'clock position.
  51. Replies
    3
    Views
    2,252

    Re: Rerrir Code 50-67

    If it starts to occur more frequently have dealer do a software update. If I remember correctly bobcat released an update to force controller to wait a little longer to verify communication with...
  52. Re: Broke power bobtach hydraulic fitting. Any idea how to replace?

    Could you possibly use something like these Field-Attachable (Reusable) Hose Fittings > Discount Hydraulic Hose.com to cut tee off at main hose install repair fitting, a threaded tee and 2 new hoses...
  53. Re: Broke power bobtach hydraulic fitting. Any idea how to replace?

    Could you possibly use something like these Field-Attachable (Reusable) Hose Fittings > Discount Hydraulic Hose.com to cut tee off at main hose install repair fitting, a threaded tee and 2 new hoses...
  54. Replies
    2
    Views
    1,381

    Re: Fastback 435 drive belt tensioner question

    1. -Take the belt off the tensioner and check tensioner bearing. If bearing is worn out you will run out of adjustment travel. Be sure to adhere to tensioning specs when retightening to prevent...
  55. Replies
    22
    Views
    2,864

    Buying Advice Re: Best way to sell a tractor?

    Offer it as a package but willing to sell implements separate. List price of tractor and each individually with a discount if taking total package. Same strategy dealers use when bundling for a new...
  56. Replies
    9
    Views
    7,350

    Re: CT235 won't turn over

    Lockport; Did you happen to readjust brake pedals recently before this stalling when getting off happened? I ask because mine does this occasionally and started soon after adjusting brakes, I got...
  57. Replies
    62
    Views
    8,355

    Re: Where's the older users

    Got my Medicare card, 1st SS check, and quit work (retired) 3 months ago. Work 2 weeks around home catching up all things I put off due available time while working then when body starts to shut down...
  58. Replies
    2
    Views
    1,350

    Re: 435 ZHS swing problem

    Is there any noise from the motor when it starts slowing down? Noise like metal squeak or screech? This could be motor brake not releasing due to debris lodged in orifice of sequence valve. When...
  59. Re: Noob needs instructions on servicing CK20S HST

    Bobcat filters for a CT120 or CT122 will be same as Kioti CK20. There are 3 drain plugs for the hydraulics 1-center in transmission housing and 2 (1 each) at rear axle housings.
  60. Replies
    7
    Views
    900

    Grapple Re: WR Long 3rd function valve issue

    I think SDEF is on the right path. Check the grapple couplers. The loss of operation in 1 direction, tires to move or moves partially then stops is what we see when a loose QD on the loader...
  61. Replies
    6
    Views
    962

    Re: Busted my engine

    More than likely you partially sheared the key in the flywheel. Simple fix, remove flywheel and install new woodruff key.
  62. Replies
    41
    Views
    4,801

    Re: How much can a 40hp tractor tow??

    Bobcat's version of that DK40, CT440 list tow capacity of 1433# tongue weight and 7716# total trailer weight. That is without any front ballast so with loader and bucket and using reasonable slow...
  63. Re: Opinions on Kioti's long term stability/viability in the US market?

    FYI; Cruise control will not engage if brake pedals are split, thus reason for the light.
  64. Replies
    1
    Views
    780

    Re: Oil in 1996 Polaris ATV

    Fill the tank full of gas and run it. I usually run 50:1 mixed in my '09 Bobcat/Polaris simply because when I run close to empty the only gas I have close at hand is mixed for chainsaw or boat. ...
  65. Re: Looks like I bent the coupling for the loader

    Yes, engine OFF for all of it.
  66. Re: Looks like I bent the coupling for the loader

    Put the joystick in float position then using a brass pin or wood dowel push in on the female QD poppet to make sure there is no pressure, then look inside the QD to make sure the poppet is setting...
  67. Replies
    14
    Views
    1,666

    Re: Quirky steering on CK2510

    This may be just the style of steering system used. In their previous models CK & DK series Kioti used 2 different systems. The CK 20-35 had "Load Reaction Steering". The when steering wheel was...
  68. Replies
    7
    Views
    1,178

    Re: CK27HSt idle speed.

    Mine idles in the 900 -1000. Same engine as CK27. I usually let it idle closer to 1100 - 1200 just seems to run smoother at that speed.
  69. Replies
    11
    Views
    9,503

    Re: trivial question about the step kit

    Here are the installation instructions for the step. This should have been in the box with the parts or dealer could have printed theses out for you. The holes are drilled through inner wall of cab...
  70. Re: Sizing a hydraulic control valve - size for pump flow, or total flow?

    the 8 GPM would be the better choice.
  71. Re: Sizing a hydraulic control valve - size for pump flow, or total flow?

    Backhoe will get pump flow only. It is difficult to find valves rated less than 10 GPM so 6.7 or 9.9 won't make any noticeable difference.
  72. Replies
    13
    Views
    2,118

    Re: Kioti HST PTO true neutral position?

    The DK uses hydraulic pressure pushing against a clutch pack to engage PTO with spring pushing some pressure on the clutch pack to act as coaster brake. The PTO drive gear is always in contact with...
  73. Replies
    52
    Views
    10,892

    Re: Brush Grapple Preferred Width?

    The bucket that came with the loader is 68" and grapple is 60". When using it for loose brush it will grab enough with branches hanging over the sides to make it interesting weeing where your going...
  74. Replies
    20
    Views
    5,590

    Re: JD Power SSQA upgrade

    My diverter on my hydraulic SSQA has some leakage but any leakage through the diverter is equal to both side of the piston cylinder, base end/extend side has more push force at same pressure than rod...
  75. Re: HSA questions. Using funds when no longer on a HSA plan?

    Each company may have different rules but check out possibility of taking a loan form 401k. I had this option and used it some 10 years ago to clear out all credit card debit and couple large...
  76. Replies
    24
    Views
    6,456

    Re: Rear remote kit

    Try calling a Bobcat dealer and ask for P/N 7150493. This is the 2 remote valve kit that fits CT230/Kioti CK30. List price is around $600 + shipping. Closest Bobcat dealers are in Oklahoma City or...
  77. Replies
    11
    Views
    1,649

    Rotary Cutter Re: Tips on using grapple with a rotary cutter

    The second one says "shear pin" so the first "torque limiter" is probably slip clutch.
  78. Replies
    11
    Views
    1,649

    Rotary Cutter Re: Tips on using grapple with a rotary cutter

    Do as stated above then drive first time cutting with grapple about 2" off the ground. If you missed something you should feel it with the loader/grapple before running over it.
  79. Replies
    24
    Views
    3,483

    Re: 3pt, PTO, Diesel

    Your Bush Hog requirements (what you need to cut, width, etc.) would be determining factor for size and PTO power of tractor.
  80. Re: Red indicator light, right side second one down? Dk40 hst

    Cruise control will not work when brake pedals are not locked together either.
  81. Replies
    7
    Views
    1,596

    Re: Leinbach Single Bottom Plow

    Measure the share (bolt on cutting edge across across the bottom). 12", 14", or 16" are most common.
  82. Thread: float system

    by SSdoxie
    Replies
    36
    Views
    6,883

    Loader Re: float system

    When if float the oil in the lift cylinders can move back and forth between rod end and base end of the cylinder. When bucket touches the ground, there is still some available travel room in the...
  83. Re: Unloading without supporting the rear-end of the trailer a bad idea?

    I use pair of jack stands for 2 reasons.
    1. Seen a few trailers with rear of frame bent down at rear axle.
    2. lesson learned for another's experience. Former boss of years ago was loading a skid...
  84. Replies
    6
    Views
    1,456

    Re: 435 fast track boom swing hydraulics

    My mistake. That one is different than some other models. That bolt holding pin in form the bottom comes out then pin comes out the bottom. Here is the R&R steps from service manual.

    465623
  85. Replies
    6
    Views
    1,456

    Re: 435 fast track boom swing hydraulics

    2 ways to do this:
    With cylinder mounted in machine (this is way most dealer techs to it)
    1 - swing boom full to right then remove pin at the boom, reach in the front hole and remove both hoses,...
  86. Replies
    15
    Views
    5,352

    Re: hydraulic top link adjustment question

    There are spring loaded hinged tabs that swing out over the lower pins to keep implement locked on. In the picture those T handles on top are pulled back holding the lock tab open. Once you get back...
  87. Replies
    15
    Views
    5,352

    Re: hydraulic top link adjustment question

    There are spring loaded hinged tabs that swing out over the lower pins to keep implement locked on. In the picture those T handles on top are pulled back holding the lock tab open. Once you get back...
  88. Replies
    15
    Views
    5,352

    Re: hydraulic top link adjustment question

    That one looks like a good alternative.
  89. Replies
    15
    Views
    5,352

    Re: hydraulic top link adjustment question

    Here is some options that could make it easier. Not in any recommended order.
    1. If rear remote has float, put it in float before getting out then move cylinder manual (will take some force to push...
  90. Replies
    27
    Views
    3,784

    Re: Rebar/ labor costs?

    Rebar needs to be installed, supported up on stakes so it is middle of the concrete. This will prevent truck from backing in and/or use of wheel barrow to move concrete to rear of the building, thus...
  91. Replies
    24
    Views
    3,452

    Re: Diesel Can Spout Mechanism Into the Tank

    You should be able to run with it in there for now, fish it out later but it might hang the gauge float so watch your fuel level. Might consider removing the gauge float when you go fishing for the...
  92. Replies
    111
    Views
    12,092

    Re: How much do you know about WWII battles?

    Came close James. Got 27
  93. Re: Crankshaft Pulley Alignment on B8200 Tractor with D950 Engine

    There is, or was, a corresponding dot on end of one of the splines to align it. Hopefully it isn't damaged too bad and you can find it.
  94. Re: Can I increase my FEL lifting capacity by replacing lift cylinders?

    Changing to larger lift cylinders will increase the lifting ability, not necessarily the capacity. Capacity ratings use 3 variables 1 - ability to raise load to full height, 2 - structural integrity...
  95. Replies
    66
    Views
    6,989

    Re: Kyoti CK35 HST hydraulic woe's from a newby

    There are 3 pump systems in this tractor. 1-loader/3pt, 2- steering, & 3 - hst/charge pump. #1&2 share the same suction inlet line. All 3 share the same reservoir and suction filter (filter below...
  96. Thread: PowerArc 200ST

    by SSdoxie
    Replies
    6
    Views
    1,665

    Re: PowerArc 200ST

    Use the "E6010" port for ground cable with the 6011 rod. Don't understand the principles of it, but does seem to run smoother. Just be sure to move cable back to normal port with other rods or it...
  97. Replies
    416
    Views
    144,449

    Re: If you have Toolcat questions, ask them here...

    To clarify brake release; the A,B,&C series with straight axle does have the access to install a tapered blot kit to mechanically release the brakes. D series and later (independent wheel...
  98. Replies
    416
    Views
    144,449

    Re: If you have Toolcat questions, ask them here...

    To clarify brake release; the A,B,&C series with straight axle does have the access to install a tapered blot kit to mechanically release the brakes. D series and later (independent wheel...
  99. Replies
    416
    Views
    144,449

    Re: If you have Toolcat questions, ask them here...

    No there is not. There is no "tow" or "freewheel" provision on the Toolcat.
  100. Replies
    53
    Views
    11,839

    Re: New to Quick Hitches - What do I need?

    My QH is Speeco and it does have the extended top hook, places the hook out far enough that the side frames of implement top link do not hit the pins of the hook.



    Sure this moves the top out...
Results 1 to 100 of 2446
Page 1 of 25 1 2 3 4
© 2017 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.