Search:

Type: Posts; User: SSdoxie; Keyword(s):

Results 1 to 100 of 2508
Page 1 of 26 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    5
    Views
    709

    Re: toolcat traction control

    The rear wheel alignment light must be on to send confirmation to controller that rear wheels are not turned to any angle. The alignment may have moved over time so although the rears are straight...
  2. Replies
    10
    Views
    489

    Re: 3 point issue, jumpy while inactive.

    The is a sensitivity adjustment for the 3 point MLS (positioning valve). The adjustment is set screw with a jam nut on it located next to the shaft the speed adjusting rod connects to on the front...
  3. Replies
    4
    Views
    342

    Re: Oil Filter Question

    Double check that Fram filter cross number. Using the Wix online cross reference the Fram #PH3614 comes up as a Wix #51348. Price check on Amazon shows the 5700 @ $20 and the 51348 @ $9. No idea...
  4. Replies
    464
    Views
    171,338

    Re: If you have Toolcat questions, ask them here...

    Try holding down the code button and the AUX button simultaneously.
  5. Replies
    464
    Views
    171,338

    Re: If you have Toolcat questions, ask them here...

    The service reminder clock is a feature built into the Deluxe (keyless) panel. That is where it started but now may be in all, I do not know for sure. This is an option that can be turned on and...
  6. Replies
    7
    Views
    634

    Re: Starting Issues CT335

    The OP posed this question over in Kioti forum also. He replaced fuel pull relay. Either the relay had too high resistance internally of there was a loose connection in the plug that went...
  7. Replies
    18
    Views
    960

    Re: CT225 LIFT POWER

    The 230 & 235 have the same 7TL loader and hydraulic system as the 225 so no difference in lift capability.
  8. Replies
    7
    Views
    634

    Re: Starting Issues CT335

    "I have also tested the connection to solenoid and get the 1 second 11-12V when turning to ON position and the other terminal shows 11-12v constant."

    Based on this above the electrical system is...
  9. Re: 335 bogs down and tries to die intermittently?

    The pump on 335 has some torque limiting built into it that sense flow & pressure then will automatically destroke the pump (reduce flow) to maintain engine RPM under sudden high load changes, but...
  10. Replies
    19
    Views
    741

    Re: Boom Will not float

    Bobcat does use a series valve, in that fluid returning from lift cylinders does go into the Open Center flow not back to tank like on most tractor valves.
    It does sound like the lift spool is not...
  11. Replies
    464
    Views
    171,338

    Re: If you have Toolcat questions, ask them here...

    The radiator location of the 5610 (above the engine behind the cab) makes it less of problem of grass clippings clogging the radiator screen if you are going to be doing a lot of mowing. Having the...
  12. Replies
    3
    Views
    562

    Re: triple gear pump o rings

    Inspect the pump housing for very fine hair line crack at the threads.
  13. Replies
    1
    Views
    773

    Re: Add Aux Hydraulic port to 773 Bobcat

    If you want to run 2 auxiliary ports at same time you need to install a Rear Auxiliary kit and run the line from rear aux valve out right hand side of machine and down RHS lift arm to the front. If
  14. Replies
    1
    Views
    813

    Re: Bobcat 943 hydro issue

    I think you are on the right track looking at relief valve if loss of pressure is only on 1 side in 1 direction.
  15. Replies
    5
    Views
    962

    Re: hydraulic lift arm question bobcat 763

    To test which circuit (lift or bucket) is building pressure you have do more than lower the seat bar to unlock the pedals. The BICS system has an electric solenoid that blocks the oil flow from the...
  16. Replies
    6
    Views
    2,380

    Loader Re: Starting issues CT235

    Glad you found something. It could be just that connection behind the loose but now you have a place to start looking if it happens again.
  17. Replies
    6
    Views
    2,380

    Loader Re: Starting issues CT235

    Not pertinent to your start/run problem but FYI: there is a storage lock hook on the clutch pedal to hold the clutch pedal depressed that can be used for times like this when trying to start engine...
  18. Re: Bobcat T300 stalls under load and hyd. fluid seems to heat up fast.

    Did you replace the motor case drain filters when new motors were installed?
  19. Replies
    4
    Views
    1,296

    Re: Bobcat 425 mini excavator questions.

    I think you can do it 2 at a time. Leave front bolts in but loose then pry up and block rear of the cab to replace rear isolator bushings. Install rear bolts but leave loose until front bushings...
  20. Re: Change to Bobcat keyless ignition from key ignition

    With a key style panel that harness does go back to the main harness and panel connection, it powers up the panel and signals to operate fuel solenoid and starter go through the panel. With a...
  21. Re: excavator display panel controller replacing

    The risks involved with installing a used controller;
    Controllers are costly so why this used one removed?
    Did panel come out of same model machine. If panel came from a model that had 4...
  22. Thread: Remote valves

    by SSdoxie
    Replies
    17
    Views
    1,724

    Re: Remote valves

    Comparing rear remote kits in MIE online parts website shows the ck2510 only has option for one rear remote kit while the larger HP CKs have 2 rear valve kits available. The single valve is a detent...
  23. Re: Beast Died when I sat back down - No start - no clicks either - Solution found

    That same fuse also supplies power to all of the neutral start/saftey switches. Failure seemed to occur when plunking down in the seat and stated it restarted with new fuse but seat switch still...
  24. Re: 709 hook style backhoe brackets (mounts) for 773G

    773G & S185 are the same frame and lift arm so these are the mounts that will work for you.
  25. Replies
    6
    Views
    1,654

    Re: Rear remote lever won't engage

    If you are using the remote lever closest to the seat it may have the detent which are prone to getting dry or rusty and stick. The detent is removable without disassembling the valve it is located...
  26. Replies
    13
    Views
    2,319

    Re: CT230 with 50 hours won't start

    The fuel solenoid has 2 power circuits feeding it. One is a momentary high amperage input to pull the solenoid ON then shuts off, the second is a lower amp input that holds the magnet in place. ...
  27. Replies
    6
    Views
    1,654

    Re: Rear remote lever won't engage

    I had my remote lever without detent lockup once when a coupler was not fully locked in place. That could also explain no function now if coupler has backed off enough to close the poppet.
  28. Replies
    13
    Views
    2,319

    Re: CT230 with 50 hours won't start

    Correct. I was thinking about this after my reply so checked it today. Any of the 3 switches will prevent cranking.
  29. Replies
    13
    Views
    2,319

    Re: CT230 with 50 hours won't start

    There are 3 safety switches. 1. seat switch 2. Treadle pedal neutral 3. PTO lever OFF. Try moving PTO lever, I have had mine get in position that PTO was off light was off but switch did not...
  30. Replies
    39
    Views
    13,490

    Re: Weak curl function

    I suspect there is a partial restriction in QD connected to the base end of the curl cylinders. A partial restriction here will slow down oil flow out of the cylinder thus creating extra pressure in...
  31. Replies
    27
    Views
    2,849

    Loader Re: Removing Bucket Cylinders

    Set loader down with bucket flat on the ground. Remove the hoses to cylinders first, this will let bucket relax to settled position, then remove the pivot pins. When reinstalling insert base end...
  32. Re: Machine Shuddered to a Stop, Now it Won't Move

    Just a wild guess here, I think you lost or have low Charge Pressure but that should be registering a code. Charge Pressure provides a positive/pressurized flow of fresh oil to the HST without it...
  33. Replies
    3
    Views
    522

    Re: CK25 Head Gasket

    The site window to flywheel marks gets cover up by the loader mount frame. Have to remove the loader mounting frame to see it.
  34. Oil & Fuel Re: FULL SYNTHETIC 2-cycle engine oil in Stihl MS-261 chainsaw?

    Majority of my 2 cycle fuel use is with the boat, pre-mixed @ 50:1, no oil injection. I use Mercury Quicksilver full synthetic and use this same in chainsaws, weed eater, and leave blower. I try to...
  35. Replies
    54
    Views
    10,417

    Re: JD 14T baler with small tractor

    Dad had a 14T baler while I was growing up on the farm. When in my teens (some 50 years ago) I had the job of baling road ditches and some other small areas not worth the effort to plow and till. ...
  36. Replies
    9
    Views
    1,894

    Re: Shear Bolt.........Am I doing this right?

    The diameter of a shear bolt/pin needs to be same as the hole otherwise the movement between the shaft and PTO create it's own shear action. Use a soft grade (#3) 1/2" bolt with a self locking nut. ...
  37. Replies
    6
    Views
    4,102

    Re: CT 335 HST Tranny problem

    Follow the shift linkage rod from lever back to where it connects to case. There is a bell crank that goes over the shaft going into the transmission. This bell crank is fastened to the shaft with...
  38. Front-End Loader Re: Help with loader mount for Bobcat CT450 please!

    509971

    The attached is parts illustration for that 9TL loader. Note: item #12 bushing requires qty 8, means these are used on the front 4 bolts of each bracket. Looks like they used a bushing...
  39. Thread: TRACTION LOCK

    by SSdoxie
    Replies
    3
    Views
    4,517

    Re: TRACTION LOCK

    The solenoid has 3 wires on it. 1 is ground, 1 is high amp 12v momentary pull to pull the stem up, and the other is low amp 12v to hold the solenoid in unlock position. The Pull circuit which has...
  40. Replies
    1
    Views
    857

    Re: Bobcat 753 Pedals Stuck

    Bobcat uses a pedal locking system integrated into the seat bar to lock pedals in neutral (center) position when seat bar is raised to help prevent loader movement if pedal is stepped while exiting...
  41. Re: Turn signal woes (or how not to get hit by traffic)

    X2 and wire them to a separate circuit so they don't flash with the 4 way.
  42. Replies
    15
    Views
    1,717

    Comparison Re: HST vs. Shuttle

    To get a more true idea of power loss through HST compare PTO HP of both gear and like model HST. That difference in lower HST pto HP is what the charge pump/replenishing circuit is using from the...
  43. Replies
    12
    Views
    3,240

    Re: CT445 high pitch whine in reverse

    I don't know if the updated relief valve will fit in older pump, or if the charge relief can be replaced without removing and disassembling pump. Won't to ask.
  44. Replies
    12
    Views
    3,240

    Re: CT445 high pitch whine in reverse

    The in field fix was to add a hose to act as an accumulator to absorb the vibration pulses caused by the charge pressure relief chattering. Final production fix was a redesign of the relief valve to...
  45. Replies
    20
    Views
    5,341

    Re: ct235 no glow plugs and no start issue

    Before replacing the control module do a couple more tests. You said when checking glow plug relay with key to ON lost voltage. Test relay in same place but turn and hold key to left...
  46. Replies
    20
    Views
    5,341

    Re: ct235 no glow plugs and no start issue

    Here is the schematic for it. Let us know what you find.

    505096505096
  47. Replies
    20
    Views
    5,341

    Re: ct235 no glow plugs and no start issue

    You did not mention if the Battery light and Oil Pressure lights come on in dash when key is turned on. If they do not come on, turn key to the left and hold (this is manual glow plug and circuit...
  48. Re: T300 Charge Pressure Issue On Right Motor Only

    Right side pump MAY have suffered internal damage due to sudden loss of fluid when the hose blew. Way to check is to remove both high pressure drive hoses to right motor at the pump then use steel...
  49. Replies
    8
    Views
    1,641

    Re: Bobcat 863 will not idle down

    1. Yes. If you disconnect the cable at rear (engine compartment) you should be able to work the throttle by hand. It won't stay where you put it because that is done via a friction washer at the...
  50. Replies
    8
    Views
    1,641

    Re: Bobcat 863 will not idle down

    If the problem is in the governor the timing cover has to be removed. The governor is inside the the cover and will require shop service manual to set it up correctly. The throttle linkage is cable...
  51. Re: Third function dirverter valve vers True 3rd function valve

    The loader valve does have PB already on it. Look at the steel line coming off the inside (left side) of valve running back to the rear. You will see what appears to be an extended female thread...
  52. Loader Re: Kioti CK27 Joystick installed wrong... questions

    I think you will also need to swap the two bucket hoses to keep bucket dump when joystick is moved outward, to right.
  53. Replies
    9
    Views
    1,972

    Re: Bobcat s205 control handles locked

    Glad you got it going.
    Please explain how you found the problem and how you fixed it. This may help others that come here looking for assistance.
  54. Replies
    9
    Views
    1,972

    Re: Bobcat s205 control handles locked

    The door sensor only applies to OEM bobcat door work door that has the Bobcat sensor. That sensor sends a signal to controller to lock the ACS if door is open.
    Stray voltage or short in the front...
  55. Replies
    5
    Views
    4,226

    Re: melroe bobcat 753g "input" error message?

    Low battery voltage can cause the "input" error to display.
  56. Replies
    9
    Views
    1,972

    Re: Bobcat s205 control handles locked

    If you have a cab door, make sure the door is closed fully latched before starting the calibration sequence.
  57. Replies
    9
    Views
    1,972

    Re: Bobcat s205 control handles locked

    Which actuator did you replace lift or tilt?
  58. Replies
    464
    Views
    171,338

    Re: If you have Toolcat questions, ask them here...

    No idea of cost but Bobcat does show a pre-cleaner kit for the F-series in their online catalog. P/N 7270129.

    FYI: I see Bobcat has redone their web page and the online catalog now works Google...
  59. Replies
    54
    Views
    5,591

    Re: auto darkening helmets

    The grind mode is OK but you have to remember to turn it back to weld. I'm a slow learning I guess, it took me 3 repetitions to sink in. The switch on mine is inside the hood which requires taking...
  60. Thread: Bobcat 533

    by SSdoxie
    Replies
    8
    Views
    3,997

    Re: Bobcat 533

    None at all. Never seen a 533 that is why I misread the model number.
  61. Thread: Bobcat 533

    by SSdoxie
    Replies
    8
    Views
    3,997

    Re: Bobcat 533

    Sorry, I was reading this as model 553 not 533.
  62. Thread: Bobcat 533

    by SSdoxie
    Replies
    8
    Views
    3,997

    Re: Bobcat 533

    Be advised if this has an Isuzu engine it has been repowered. Original engine was a Kubota. Might want to check on source/availability of parts for the engine since Bobcat would not have them.
  63. Replies
    13
    Views
    3,530

    Re: Did Bobcat make a gas powered mini backhoe ?

    No it was not Terramite, it was Earthforce made in Chech Republic. Bobcat only had this backhoe line for about 4 years, the purchase was primarily to obtain the manufacturing facility to expand in...
  64. Replies
    2
    Views
    1,034

    Re: Bobcat 463 cooling system question.

    First - Welcome the TBN.
    The 463 is a skid-steer loader considered construction equipment so this is correct place to post the question.

    From what you are describing - gauge in-op but wires and...
  65. Replies
    13
    Views
    3,530

    Re: Did Bobcat make a gas powered mini backhoe ?

    Bobcat did have a line of smaller tractor backhoes similar to the Termite. The smallest was B200, all were Kubota diesel powered no gas version. If it is one of these the starting issue may be...
  66. Replies
    13
    Views
    3,530

    Re: Did Bobcat make a gas powered mini backhoe ?

    No idea what the first model was, that was long before my time with the company. I do know Bobcat started out in mini-excavator business purchasing machines from Komatsu. At that time the 231 was...
  67. Replies
    13
    Views
    3,530

    Re: Did Bobcat make a gas powered mini backhoe ?

    They never made one that I'm aware of and I retired last year after 18 years with Bobcat.
  68. Replies
    15
    Views
    4,464

    Re: hard starting CT235

    That rough running for a short time when first started with engine cold is normal especially if started before the glow pug light goes out, or if glow plugs are weak/faulty. This tractor has...
  69. Replies
    9
    Views
    7,154

    Re: Bobcat 743B Left Reverse Drive Problem

    It could be something sticky or catching in relief/replenishing check valve but it sounds more like steering linkage is loose. Check all rubber bushings and especially the arm that clamps on to the...
  70. Replies
    16
    Views
    6,536

    Re: CT235 won't start. Fuel solenoid won't engage

    Kioti and Bobcat will be the same parts for the solenoid. Buy them from Kioti
  71. Replies
    11
    Views
    1,712

    Re: What size battery for CK30 HSt?

    I just replaced mine 2 days ago, installed a 24F 700 CCA. The F places the terminals forward of the air filter housing so next time recharging is needed it will be easier access. Any sixe you use...
  72. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    You have it correct Dave. As an installation precaution, rig up a Tee and pressure gauge so you can check free flowing pressure through the Backhoe valve when the A or B port is activated. Test it...
  73. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    The relief valve for the hydraulic circuit (loader, rear auxiliary, & 3 point) is at the inlet port of the loader valve. Flow of oil goes from pump to loader to rear aux, to 3 pt. so the loader...
  74. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    The pressure relief in the loader valve would open in this case to momentarily protect the pump and the engine will RPM will decrease. This would be no different than going to a dirt pile with the...
  75. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    VONBERG VALVES INLINE CHECK VALVE 19139-.188

    Here is a simple inline check valve for Surplus Center. Shipping will likely be more than the valve @ $8.95.
  76. Replies
    2
    Views
    1,451

    Re: 853 engine knocking ,loud.

    The 853 has an Isuzu 4JB1 engine. This same engine model with different oil pan, intake & exhaust manifolds, and flywheel
    was also used in Mustang skid-loader model 960 & 2060 (2060 is turbo...
  77. Replies
    8
    Views
    13,701

    Re: Trick to unlocking the traction lock?

    This question was posted in 2010 so hopefully he figured it out.
    For anyone coming across this with same issue, check your Park Brake switch. If Park Brake is "ON" or switch is faulty the...
  78. Replies
    2
    Views
    1,003

    Re: Bobcat 553 magnetic seat switch.

    Bobcat sells a kit to replace the seat switch with a Push to Operate button system so is same as current production loaders. It has a different control box at rear of cab and the Traction Lock...
  79. Thread: new to me 863

    by SSdoxie
    Replies
    3
    Views
    1,614

    Re: new to me 863

    Dealers replace the belt without pulling engine. There are special tools required. Need locator pins to position crank & camshaft at TDC then lock them in place to prevent turning and also requires...
  80. Thread: Fan Belt

    by SSdoxie
    Replies
    5
    Views
    2,734

    Re: Fan Belt

    Check the alternator mounts. Make sure both top and bottom are tight, no cracks in the mount, and the pulley is aligned correctly with the crank and water pump pulleys.
  81. Thread: new to me 863

    by SSdoxie
    Replies
    3
    Views
    1,614

    Re: new to me 863

    The G series is newer version of 863. G series came out in 2000 and was last version made. The electronics are totally different in G to F series.
    I would not use Universal Tractor fluid in it. An...
  82. Re: Bobcat 963 "C Series" Fuel Pickup Tube Location

    Fittings will be somewhere in the front portion of main/primary tank = look in between engine and hydro pump assembly. The 800 series have the belt drive on left hand side so fuel tank fittings are...
  83. Re: Limited slip differential versus Hydrostatic traction control (HTC)

    Mountaineer, Dealer is correct. Any 5610 that has the required cab & mainframe harness, axle shafts to accept the added speed sensor came with HTC as standard equipment, it was/is option for 5600. ...
  84. Replies
    10
    Views
    3,605

    Re: Bobcat 753c overfull chain case

    Thumb switch on right handle is for momentary hydraulics to front couplers is bi-directional. Typically used for cylinder operations. The trigger switch on right handle is for constant flow (detent)...
  85. Replies
    10
    Views
    3,605

    Re: Bobcat 753c overfull chain case

    Look for another one of these for the other motor. Bobcat did change sometimes with different series production, but most 753s had 2 filters - 1 for each motor.
  86. Replies
    10
    Views
    3,605

    Re: Bobcat 753c overfull chain case

    Case drain filter is a small metal canister in-line with the hose. Follow the smaller of 3 hoses going to the drive motor is the case drain, follow that hose back from each motor until you find it. ...
  87. Replies
    10
    Views
    3,605

    Re: Bobcat 753c overfull chain case

    Not necessarily the drive motor seals bad, could be, but fluid is going past the motor carrier seal. The carrier is the assembly that bolts to the chain case frame and has shaft that has splines on...
  88. Replies
    5
    Views
    1,236

    Re: Bobcat 331D no start

    Is there any smoke from exhaust when cranking? If there is smoke, it is getting fuel but firing - 1st thought would be check glow plug/preheat circuit.

    No smoke is no fuel delivery - check fuel...
  89. Replies
    109
    Views
    19,334

    Re: Bad day,Lost an engine

    Load or power to the drive train varies depending on resistance to wheel rotation. At full maximum, stall point, the additional HP combined with slightly higher relief means more torque available to...
  90. Replies
    109
    Views
    19,334

    Re: Bad day,Lost an engine

    Same drivetrain (other than HST in 235) is used on all 3 models. Done for simplicity/commonality of parts for manufacturing.
  91. Replies
    109
    Views
    19,334

    Re: Bad day,Lost an engine

    The 235 engine will fit right in without modifications or other required parts. Part number of the 235 HST is different but that is only because of design of internal directional check valve and...
  92. Replies
    18
    Views
    5,514

    Backhoe Re: Woods subframe to CT230

    The rear mounts of sub-frame will be the same as CK30. The question will be how the front mounts are installed/located. If mounted to the transmission case, flywheel housing, or engine then it...
  93. Replies
    12
    Views
    7,135

    Re: What model of toolcat do I have?

    The front boom design did start with the C-series however Independent Suspension stated with the D-series. With Independent suspension and a Kubota engine it is either a D or F series. First 4...
  94. Thread: Coolant in Oil

    by SSdoxie
    Replies
    20
    Views
    5,444

    Re: Coolant in Oil

    Does this have an engine oil cooler, oil cooled by radiator coolant? If so that would be a place to check. Exchanger rust through and push anti-freeze into oil.
  95. Replies
    6
    Views
    2,511

    Re: 773G turbo B.I.C.S. messing up

    Another possibility I just thought of, although less likely because you say the Traction Lock Override seems to work fine, is loose ground from the controller. Easy enough to check as all the...
  96. Replies
    6
    Views
    2,511

    Re: 773G turbo B.I.C.S. messing up

    For unknown reason the controller is reading the seat bar is being raised/moved out of normal operating position. Three checks to do before at the sensor and/or circuit: 1. Turn key (power up the...
  97. Replies
    22
    Views
    8,646

    Re: Bobcat 753 Arm Lift Problems

    I don't have any good advice on getting this out. The piston does need to be kept square with the barrel as it comes out so it is sliding only on the seal. Coat hanger likely has too much flex to...
  98. Replies
    6
    Views
    2,511

    Re: 773G turbo B.I.C.S. messing up

    With both brakes and loader locking indicates problem in sensor circuit. Could be loose connection in feedback or ground circuits. The seat bar sensor and Press To Operate Button are signal input...
  99. Replies
    6
    Views
    2,511

    Re: 773G turbo B.I.C.S. messing up

    Do the brakes lock up along with the loader control or just loader functions?
  100. Replies
    22
    Views
    8,646

    Re: Bobcat 753 Arm Lift Problems

    Glad you found the lift problem. That rod should be salvageable, clean up end of the threads. I don't see any evidence of Loctite on the rod threads. Red (hi-temp) Loctite is called for in service...
Results 1 to 100 of 2508
Page 1 of 26 1 2 3 4
© 2017 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.