Search results

linkage adjustment rod was broke and the part it pivots on was froze up now we have it free but would like to find some diagrams and part numbers for the assembly slammer

Hi I have a Jinma 284 just started grinding when you put in gear went to adjust pedal but did not help. I do not know if it is a single stage or dual stage clutch. The manuel says it needs adjusted occasionaly. Any help or tips appreciated.I did see a video on a 254 but the tractor would not...

Anybody have any tips on getting tie rod end off Thanks

does anyone know where I can get parts for this old planter Thanks Slammer

Dont know if this is correct thread or not,if not can someone direct me to right one. Used neighbors J d 290 corn planter there is a disc in front of fertilizer chute we are thinking they are wore out as it kept plugging up,cant seem to find out what they are called and if that is the...

Where in the heck is the petcock on the radiator on a Jinma 28 4 ? s it under that shroud or brace? Thanks Slammer

need to replace front boot on my jinma 284 looks like you take cotter pin out of bolt, take bolt off. that tie rod or steering should drop or tap out correct.slip boot on and replace

anyone know the air pressure on Jinma 284 front and rear Thanks Slammer:)

Checking my book but cant find siz e of metric bolt for the alternator (there is a spacer it goes thru also) any help appreciated thanks slammer

Metric bolt vibrated out of spacer on alternator,looks like a M8 but dont know the length.Anyone know the len. you should be able to get this bolt at hardware store if you know len. right Thanks for any help. Slammer

I have a 21 horse craftsman overhead valve ,the machine burns oil I talked to aguy and he wanted to replace whole engine,but someone else said it could be the overhead valve and could be repaired any thoghts on this would be appreciated

Just looked at the thread about oil pressure.My Jinma 28 has great oil pressure until it runs for about a half hour then the gauge steadily drops,but still maintains pressure but drops close to the red mark I was thinking I just have a bad guage. Any tips Thanks

I have a craftsman 21 horse 46 in cut hydro-stat mower. It runs great until you engage mower then it cuts out backfires and almost shuts off any advice greatly appreciated Thanks Slammer

put a new tach sensor on my 284Jinma,put it on did not register,screwed it in a little further and the tach reads and the hour meter works. The problem is the tach meter don't seem to read right,is ther anyway to calibrate. Thanks Slammer

picked up a 2 bottom Dearborn 3 pt hitch plow for my Jinma 284.The problem is the arms are to short,I could get about 5 inches welded on but don't want to use the use of my King Kutter tiller and brush hog.I know last year I posted and had replys that said I would have no problem pulling...

I have an old IH 46 baler fly wheel tips needs bearings but I was wondering what am getting into replacing them anywhere you can get a repair manuel on how to do it Thanks

Had my Jinma 28 to the mechanic,say (he called it a tach sensor).Screws into engine block, must read the fly wheel. Is this the correct name of part?

19.5 horse craftsman wont go in gear.Changed right rear tire ,got a new snapp ring to put on but did I loose a key that goes in or what? Ran til I changed tire

Hi I dont know if this quite fits in here but I borrowed a two row horse drawn corn planter off of a friend and lost a lid for one of the corn bins. I know you can get replacement parts for these but cant seem to locate any. Any help appreciated ThNKS sLAMMER

Hi I seen another elec problem on here also I dont have fuel gauge and tak however ther is power to them.When you turn key on fuel gauge and tach will move then fall dead when engine starts We were thinking sending unit in tank and something stuck inside tach meter.We had tach meter but it is a...

First thanks for the help with banjo bolt. Run tractor thirty minutes and my temp gauge goes up over 80,plety of fluid and it dont seem hot,the gauge does vibrate alot when I start up thanks.

Hello I found a hole in my hydraulic line and a Jinma dealer fixed me right up with a hosde and fitting. I put it on and had a leak on what looks like maybe another pump to me,this could have been my main leek to begin with.A steel line runs up from under the seat on the right side if your...

Hi I had a question a bout my Farmall m Hydraulic resivoir leaking. DJ 54 and kevinj sent me replys. I can see why you would see stars that unit looks extremely heavy. We got it in garage finally and took the small plate off to check it out,and have some pics. Where can you pick up a cheapie I...

Hi I have a old Farmall M The resivor tank for the hydraulic lift leaks like a sive,looks like someone just dropped bottomand sealed with perma-tex. I was wondering is there a gasket you can get to put in. I asked before if you had to split tractor to fix this and they replied about a pump,the...

Hi I have an old Farmall M and the hydraulic reservoir leaks almost as fast as you dump hyd. in My question is can you get or make a seal to repair it without splitting the tractor THanks for any help:cool:

Just recently we have noticed after the Jinma 284 gets warmed up occasionally you put the tractor in gear and it hesitates like it is not engaged the fluids are good but I seen in owners manuel you occasionally have to adjust clutch linkage? Anybody else have any experience with this Thanks...

Hi my son has a Toro lt 12 the stick shift broke,we had it welded what si the trick to run it thru the dash and run it thru the slot for the safety switch and shifting I cant see where the whole bracket comes off.. Thanks:confused:

I have little black junk plugging up my fuelsystem. I took the little screen out of tank and put a filter on the fuel line,it plugged up again on the little hole cominig into the sediment bowl,just wondering if it would be feasible since I already have a filter on the line if I could drill the...

I would like to get some info on the 46 Baler. The fly-wheel dropped a little and a seal leaks. I would like to find some info on replacing the seal nad what Iam getting into wiht the fly-wheel. I want to replace bill-hooks but it baled pretty good the last time I used it except fly-wheel rubbed...

I Found a two bottm 3 pt hitch Ford plow wondering if it will hook up and most importantly if my Jinma 28 horsepower disel will pull them without much trouble Thanks Slammer:D

Hi thought there would be a thread on this but could not find any. My baler the fly wheel dropped down and rubs on tounge 90wt. oil also leaks out.I was wondering if there is a man. I can pick up on how to replace seal(I think) and the parts I would need.The roof leeked and bill hooks got a...

Hi JUst registered I have a Jinma 284 and a smll farm Glad to be here hope to get help and hpoefuly supply some help Thanks Slammer