Search results

Is rolling it into a fire. Buggerd up my shoulder and leg and yes my pride.....

where could I find the front diff gears for a L245 DT??

owning-ML-745105-ML- Posted in wrong forum.

Does anyone have a good plan for a simple potato hiller?

My old L245 is giveing me headachs with its charging system and have mounted a GM delco altenator on it but am wondering how to wire it. The main red is easy but am confused to know which other wires need to be hooked up? Thanks Bob

My l245dt needs a new cap and was wondering what the pressure should be? The old cap is from Japan and says 0.9 but not sure if it is bars or kpa's or pounds. The dealer wants $24.00 for one......

Anyone here make a tree scoop? I need to move around about 200 trees and ain't crazy about useing the banjo (shovel) again. It looks like I could just carve up a 2 foot x 36" 3/8 pipe. Thanks Bob

I ran my Kubota l245dt out of fuel and when I got it running again after bleeding, it is running rough at part or half throttle. At full throttle it runs goood but part is rough. I replaced the fuel filter and drained the fuel tank and there was water and rust present so after refuleing...

Does anyone know if their is a coupler for the front crank available? I want to hook up another hydraulic pump to the front of my engine. This is on a L245DT

What is the max hours you would accept on a used Bobcat? 500, 1000, 2000???

I built a new bucket for my tractor from a drawing on here but am a little confused on how to and where to put the new brackets. My old bucket has a strait back on it and the new bucket has quite an angle and this is what makes it a little confusing to me.

My kubota L245DT is over charging 16-18 volts. I replaced the regulator but it still overcharges. Any idea's?? Thanks Bob

Thinking of instaling it myself but how does one fuse the lines together?? The lines are simuler to naturel gas lines.

Was pushing up dirt with my L245DT tonight while pushing under load my front wheels started bouncing and banging. I put it in the shop and pulled off the driveshaft and the splines on the end that enters the front axle are worn down to a beveld end.. Do you think that the pinion spline would be...

I know nothing about these things I usualy get a cat or hoe to remove stumps. So how deep will they go? Would one be able to cut around a big old popler tree and then push it over??? I have been digging the sides of a tree with my 25 hp kubota and then pushing it over but that takes a long time...

Does anyone know what thickness of metal for makeing a loader bucket in the 25-35 hp range??

I have an old car in the bush that i was thinking about pulling out to restore or ?? It's a late 20's early 30's Essex) it still has the wooden spoke wheels on it and a big strait 6. Does anyone know anything about these old cars? i would like to find some info, I guess it was made by Hudson but...

Are the newer type scissor style bucket tilts better than the old single pivot design? Would it be worth it to convert to the newer style?

I was messing around pushing trees with my bota and broke off the street elbow on the tilt cyl. I tried everything to get the busted off piece out but with easy outs and even heat but no luck. This is an older tractor with old cyl. and was wondering if I could just weld a elbow on or should I...

Is there a vent tube on a L245DT? I have blown out two axle seals and notice a little pressure when I remove the cap.

ok which one of you smart fellows built or know how to build a tree spade???? I would like a little one for my 25 hp kubota.

I would like to build a rops for my old kubota and was wondering what the average height is? i.e. from axle to the top of overall height. Thanks Bob

Went out and took some pictures of some old equipment at the back of my farm. This is a 32 essax

I have this old horse drawn grader and it looks like a good copy to make up a hydraulic one. What do you think? Bob

I built this and thought some of you would like to see it. The arms and harrows come off and old 40' ft harrow bar that are laying in the bush all over the country.

Has any one built one of these? I would like to make oone but am a little concerned about ballence. I would like it to run off a 5 hp motor and be able to suck a golf ball through a garden hose. Thanks bob

Hi all i am new here and this seems to be the place of a lot of good people with good ideas. So my question is can I hook up another pump to my kubota L245DT off the front crankshaft to run my FEL and leave the origanal pump (2.8 GPM) for the 3PH??? Thanks Bob from Alberta Canda