Search results

Hi Tony, Here is the fuel tank page from the 135 parts book.

Putting back the hoses for the FEL. I had new hoses made up with the old field fittings. Trouble is that 2 or 3 of them have fittings facing the wrong direction so that I have to twist the hose to get them on. Can these be turned without removing the hose completely?

Last autumn I did my own service on the saw but I have been wondering if I might have missed something. I did once take it to a Stihl dealer for a service but it wasn't cheap. Can anyone give me a list of things that Stihl would probably do in a routine service, so that I can be sure I am not...

There are 3 oil cooler filters listed in the parts book: The first doesn't mention that a cooler is in some cases not fitted (up to SERIAL NO. 85531). Element 191855M4 The second mentions cooler sometimes not fitted (from SERIAL NO. 85531) Element 1862918M91 The third also mentions cooler...

If you can let me know the number(s) on the diagram of the parts you want to have the part number for, I can look them up. But as I don't know your serial number/year, I can't be certain I have the correct 135 parts book open for your tractor. By the sounds of it you need access to the AGCO...

If the shape of the casting matches the pic of the plate then the part number for the plate is:180482M1 and the gasket is 180481M1 Available from here: Housing Quite possibly the oil is coming from the rear main seal...very common on the Perkins. 353901X1 4 Screw Unc Up to Serial or Engine...

There are some big projects going to start around here next year....a new airport and runway and a couple of large resorts one with a golf course. Plus there may be smaller jobs around here as I know I have paid for a bobcat and driver in the past more than once. I've looked into the state red...

My steering wheel has a big chrome nut in the middle. To remove this, do the wheels need to be on full lock? Thanks

Due to a mix up of the parts listing I ordered an anti-clockwise meter (from the other side of the world), but got a clockwise. Will a clockwise meter work where the original was anti-clockwise?

I'm replacing all of my FEL hoses due to age. The two hoses which operate the bucket cylinder come off at 90 degrees from the top of the spool valve (which is a bit lower than the boom pivot point) and then run horizontal along the top of the loader boom. There is no excess hose at the moment to...

Hi, After rebuilding the power steering pump and cylinders, I raised the tractor up on the FEL to get the air out of the p/s and the tractor sunk back down straight away. As the FEL goes up fine, if a bit slowly, is the cause likely to be the FEL cylinders? They aren't leaking externally. Thanks

Hi, I'm rebuilding my power steering cylinders (MF 135 cylinders on an MF 240) and a mechanic told me that I should apply Vaseline to the internals. Is this advisable or is it just a rural myth grown credible through the re-telling. Also can I use lithium grease instead? Thanks

Just bought a 240 which has 135/148 power steering cylinders. I would like to keep them if I can. Someone welded the rods to the ends instead of using pins. Got one off cleanly, but not sure about the other one yet but am doubtful. Anyone know if the rod (10 on diagram) 1749716M91, is...

Recently bought a 1979 MF240 and have started to restore her. Have been trying out my new sand blaster attachment which works really well (ordinary household Karcher pressure washer). Didn't know such a thing existed until I came across it on the net. It's quite slow going and doesn't take...

Hi, Can anyone help me identify the make and model of this pump? The standard pump is I think, a round Cessna type. This one is more like an inverted A shape and I guess it must have been aftermarket. It's leaking so I would like to try and get an overhaul kit. Thanks.