Search results

My RTV-X1140 has something draining the battery. I can charge it and it will last a week or so and then need to be charged or jump started. I thought about mounting a solar panel on the roof to help it maintain a charge. Has anyone ever done that and if so, how did it work for you? I'd love to...

I haven't opened my old gear box yet but if I turn the input shaft back and forth I can feel a very slight bit of slack. Not sure if it's gear wear or something else. I'm sure I can get a local machine shop to cut a new shaft. Wonder if those gears could be found through a generic supplier?

I know you had said, "All four bearings in my Superior 211ADF 189 6 Gearbox are just regular conical roller bearings like Timken Set 14 (L44643 / L44610). It's a common trailer wheel bearing size. The oil seals are TC 1.00 x 1.5 x 0.25 Inch" Were you able to locate the shafts and gears? I'd...

So I got this thing together. I don't think it's run this smooth since I bought it. The gear box does seem to get a little hot but I never really checked the original gearbox for heat. Thanks for all of the help!

After pulling the plate it appears that if it was tapped in the center of the plate a screwdriver could be inserted down to the top of the shaft which looks to be about 1/4" below the fill plugs. If it was below that you wouldn't get a measurement but if it was at normal level I would think you...

😱😱😱😱😱😱😱😱

OK, All my parts are in. I didn't think my old gear box was very loose but by comparison it's quite loose! Do you know off hand what thread size that is for the JD Vent? I assume it's an NPT thread? Also, is there any reason why the gearbox can't or shouldn't be mounted so the round plate is on...

Wonder what that calculates to in blade speed at full RPM. Not sure I'm smart enough to figure out that calculation without causing smoke from my ears. LOL! Might actually cut a little better. Might grenade the blades and spindle bearings. YIKES

I noticed that your pulley is painted gray. Did you paint it or get a new one?

ok, the gearbox is on the way. Was able to get my PTO shaft parts through paulbparts.com. Thanks again for the help.

I'm sure that's what I need too. I saw this one as well but it's cw/cw Ebay

Wanna be sure this is right. The gearbox in your link shows to rotate clockwise in / counter clockwise out. Looking at mine that seems right, just want to double check.

thanks again!

I called Superior and they told me that they still make this gearbox but can't sell to me directly. They manufacture it for Ariens. They gave me a number but it failed. I went to their website and sent them a message. I'm going to try to rebuild mine if they'll sell me the parts. It feels...

Thanks, I see that listed the tractor yoke number and the moog bearing number, you wouldn't have the specific part numbers for the rest would you? I'm having a hard time figuring out exactly which parts I need.

Do you have a part number and/or link for the chinese gearbox. I can't read it on the picture

I'm not noticing any play between the shafts. Just in the tractor yoke and implement yoke. How noticeable was it with yours. I'm thinking I can just get the cross bearings and each end yoke. Also, what size shear bolt are you using? The hole looks threaded on one side but I'm just dropping a...

It just helped me. Did you replace the output shaft from the Kubota?

Damn! Why couldn't I find your thread earlier?

ZZVYB6, Can you explain a little more in depth for the dummy in the room? ;) Are you saying that in my case I do need to maintain the factory positioning. Keeping the gearbox input parallel with the tractor output? Another question: I thought about hitting up a drive shaft shop to see if they...

So you're saying that if I pivoted the gearbox so that the yoke and pto shaft were in a straight line that I would have more vibration because the other yoke isn't in a straight line as well?

Bad news from Messicks. All of the parts for my PTO shaft are discontinued from Kubota. One thought, the yoke at the gear box seems to have the most slop, if I could find the ujoints based on specs as opposed to mower and deck model maybe I can have the yoke bored and press a sleeve in so it...

I noticed some slop in both yokes. The one at the tractor PTO and the one at the mower deck. I don't usually throw parts at a problem but I ordered new yokes and ujoints for both ends from Messicks. They must be having a hard time finding them. It's been too weeks and I've received no notice of...

It's been an issue for about 1 year but has progressively gotten worse. As JoeCdeere said, it has a master spline that forces the proper alignment. After further inspection, I did notice that there is now some play in one of the Ujoints. There was no noticeable play a few weeks ago. Now it's...

I have an F2560E, my deck is RC72R-F30. It's vibrating really bad. It seems to be the PTO, gear box or both. It's possible to be an out of balance blade or bent spindle but even with the belt off the gearbox still vibrates. I tried removing the shear pin/bolt that attaches the PTO shaft to...

Sadly, yes. I was shocked. I'm ashamed to say that I never really looked under that seating deck and had no clue that it could hold that much crap. I actually had to go back to my pressure washer 3 times to get it all and the reality is that I didn't. There are still little pockets of hardened...

After further review, probably the wiring. It does it with or without being connected to the sender. Also, if I just turn the key on it will climb to full hot, if I start it, it's showing about 1/2 gauge. Throttling it up it then climbs to full hot. With or without being connected to the sender.

I have a kubota F2560 Mower. Getting ready for the summer I pressure washed it. There was a ton of grass and dirt on top of the drive train under the body and fender cowling. I probably washed out a couple of hundred lbs of crap from under there. Anyway, ever since doing this, the temperature...

I just purchased this unit through an auction site. Engine runs good, it's pretty clean but it seems the axles, brakes or something is seizing up on it. Seems to be mostly in the rear. It takes a lot of throttle to make it go in forward or reverse. Any ideas?

A neighbor has a JD 650 for sell. Aesthetically it looks pretty good but it doesn't run and it's been through a flood. I pulled the dipstick and water squirted out of the hole for a good 3-5 minutes. YIKES!! Pulled the oil plug and water poured out for a good 60 secs before it turned into oil...

Just picked up a well used International Harvester 1190 hay cutter/conditioner. The previous owner was having trouble keeping the drive chain on the sprockets. After looking it over, it appears that two of the idler sprockets are the issue. they both line up with each other but not with the...

I'm looking to get new blades for my F2560 with the RC72R deck. I found these and they seem to fit according to the dimensions but it doesn't say on their site that it fits this deck.I think the blade is a little thicker, wider and longer that OEM blades. Has anyone ever used these or this...

Ok I have an old 8 hp rear tine Montgomery Wards Perfectionist tiller that has given me great service up until the tank rusted on me. I removed that tank and grabbed a plastic one off of and old riding mower. Never could get it to run right with that tank on there. Cleaned out the carb multiple...

Well I picked up a G4200 a while back. The belt was gone and the bearings to the right spindle was shot. I replaced the bearings and got a new belt (from My local Kubota Dealer). Put it all together and the belt last 100 yards. I'm thinkin I may have put it on wrong but I couldn't figure out a...