Search results

CK3510H - 300hrs - Blowing Horn/Blinker fuse - So a couple weeks ago I did a quick tap of the horn to get somebody's attention, horn made s split second sound and nothing. Investigating I found the fuse blown. Fuses dont blow for no reason at all, but couldnt find any issue. Put in a new fuse...

Here is what I did on my Kioti. I power cable from the battery to two relays. The relays then feed a marine grade switch panel. I have two LEDs mounted on the ROPS pointed forward, one mounted rear and one on a swivel kind of behind seat that I point at the PTO.

Im going to start on a project to to add some lights for a worklight and the ROPS. For the worklight behind the seat that I point at the PTO, I use the connectors for the bullet connector. Im/was going to use a relay for three LED lights that will go on the ROPS, I see that there is also a...

I got a skidding winch a while back, and can now see the benefit of a self-release snatch block. I'm going to have a sheave made, but the directions I have on to make one only has a 1/2" difference between the rims. Can I get somebody to measure the outside diameter of each rim on your sheave...

I have a Brush Hog 305 that I am goign to try and get going. Its been sitting for about 8 years under a tree. On inspection I cant decide if a nut is missing or not that holds on the stumpjumper? When I first looked at it they had wedgets sandwiched between the pan and the deck to keep it form...

I got this little project complete. Very happy with it, I purchased the receiver and used some 1" scrap. Maybe would work well for others with a ripper that have a removable shank.

Does anyone have a copy of this manual? Im specifically looking for fluid capacity's and recommendations. Also looking if there is a way to tension the chain and to adjust the slip clutch. Thanks!

I have a heavy duty single shank subsoiler/ripper that has a removable shank. Im thinking of removing the shank when not needed, and on the top of a reciever, weld up the same thickness of steel as the shank and bolt it in, thus giving me a way to have a 3 point receiver. This should work...

I want to to have a hose made that fits into my rear Hydraulics. Im still not quite sure on what size fitting goes in here? Its a new Kioti. In the manual it says to use:"PT 1/2 Coupler Socket - Hose unions must comply with ISO Standards. Dimension must be between 0.806 and 0.809." I called the...

I was given this 100gal fuel tank below. It came with an electric pump. Was used for who knows how many years in construction for refilling generators. They got rid of it because they went to the type that goes underneath a toolbox. First thing I did when I got it was drain it as it had about 15...

I have read and re-read the manual for my CK3510H and am still a little confused. When do you use the clutch aside from PTO/Starting. I am currently using it to change speed ranges (H/M/L) and thats about it. Should I use it to engage 4wd? I have been changing to 4wd while in motion and it seem...

I want to order two 12" +/- hydraulic hoses online with male quick attach on each side. Anybody know where to get pre-made hoses like that? My Google Fu isn't working for this.

We have had an antenna build for about 3 years in our coop. I made a slot that the door drops down into to keep coons or anything else from getting there claws under it to push up. Never have had an issue with anything getting in. I can get a pic of the lower door part if you want. Link to coop...

Correct, with nothing attached. I was thinking about just putting some tbolts in the lever slots with some blue locktite, still seems like there should be a better way.

I have two remote hydraulics on my Kioti CK3510H, both A-B. I have had issues a few times where I bump one of them causing the deadhead issue, but it such a small amount it takes a bit before I notice. Any ideas for locks/clamp out there to keep the levers from getting bumped? I have tried...

Does anyone have a pic behind the rear dashboard? Im going to attempt to get the brake light lever working on my new CK3510 and want to see what it looks like behind there without taking my dash apart.

Can anybody tell me who makes this tiller? I need to get some replacement tines/teeth for it

Anyone have an idea what this little three pointed knob does? The one down and to the left of the seat spring tension control. Hard to turn when not sitting on the seat but easy when I'm on it. I see nothing in the manual.

I have access to an old equipment trailer for very cheap or free. Would it be worth converting from air to electric brakes and to use it? Or would it just be still way to much weight? I would tow it with a 1ton. It currently is a "dually" I would have to spend a lot of time tracking parts down...

Fuel Tank I have never read of an issue with having the plastic fuel tank mounted on the rear getting hit by brush or backing into anything and damaging it, but sure seems like a place that it could happen. Has anyone came up with a shield for it? Loader Hydraulics Another point I could see a...

I just took delivery of a new CK3510H and spent a couple hours on it yesterday. I have searched the forum and read my manual and still am not quite sure of these couple things. I wanted to check with this group first as I would rather fix my things up first then bring it back to dealer as I do...