Greasing 2320 driveshaft
- Thread starter Phunge
- Start date
- Views: 36986
texas42
Silver Member
Did nothing to the access cover. Bolts are what was there.
Just cut out plastic so I could get to bolts.
Also, bought a grese gun end at Auto Zone that was a little smaller diameter than regular - that also helps
Just cut out plastic so I could get to bolts.
Also, bought a grese gun end at Auto Zone that was a little smaller diameter than regular - that also helps
T-Bow
New member
Not to be too redundant here but since I used everyone's advice when greasing this fitting I figured I would post my experience. I only loosened the top and lower dashboard by removing the estimated 9 bolts to gain access to the hidden panel. I tried using the workforce 6 inch push on coupler - quick connect to grease the fitting but found that the 3 inch straight needlepoint coupler - quick connect worked easier for me. The whole ordeal to grease just this one fitting took about 20 minutes. I will say that I had my father helping. The picture, if attached, is of the needlepoint coupler that I used. It was purchased at Tractor Supply. Hope this information is useful to someone else. Thanks guys.
Attachments
Victory Pete
Silver Member
I think that is the same one I used, I had to put a little bend in it though. And yes I think you only have to remove the 10 bolts for the upper and lower plastic housings.
VP
I'm not sure what all the fuss is about. I remove my mower deck, slide under the tractor, sometimes several times after moving the tractor back and forth to align the driveshaft just right, then I reach up with a regular old grease gun from tractor supply and give it a few pumps. If you are physically able to crawl under your tractor this shouldn't take more than 2 minutes after the mower deck is removed.
scrappy isb67
Gold Member
if you can get both from below count yourself lucky! On mine the zerk on the front joint is NOT accessible from below. the zerk is on the front side of the cross and doesn't line up with the lower access hole on the bottom. I can't even see the zerk from below.
yelbike
Veteran Member
- Joined
- Nov 7, 2011
- Messages
- 1,596
- Location
- Near Winnipeg, Mb, Canada
- Tractor
- John Deere 2305, 2320,Z465
Well I greased that shaft this past weekend. Here is my observations.
Rear u joint: It is accessible from underneath. You can rotate the shaft by grasping the harmonic balancer at the back of the engine.(turns stiffly but it does turn). Once the drive shaft was lines up so I could see the nipple, I just had to adjust the nipple a bit in the u-joint cross so it would allow the grease gun on. I used a pry bar to line this up. Make sure the grease come out of the four caps. Mine was 268hrs and supper dry.
Front joint: NO NEED TO DRILL ANYTHING(really guys it's a Deere, no hill billy stuff PLEASE!). Remove the throttle level, one bolt, than two more bolt on either side of the upper dash, now its as loose as it needs to be. Remove the 6 or so bolts that hold the lower dash, remove the two cotter pins that hold the cruise control and park brake levers. Voila the lower dash comes right out! Now you can see the famous side access panel, remove it. now you can see the drive shaft again. You can access from the panel if you so choose or go from the center of the floor board(I found this easier). I bet things would be smoother with needle a adapter for the grease gun, I didn't have one.
Extra thoughts: The first time will take an hour or so, but the second time can be done in 15 minutes. The worst part is actually getting the grease gun on the fitting as those u-joints are so small.
Good luck, (not as bad as it sounds but there is a lack of engineering!!)
Victory Pete
Silver Member
I finally cut access in the plastic cover. It is so much better this way. John Deere needs to do this and stop torturing its customers.
I followed the pictures and direction given by Plunge and they were a big help. It took longer the first time but after that, it goes quite fast. His advice was head and shoulders above anything I got from John Deere. It would be nice if the designers actually had to perform the maintenance on the machine. I think they would provide access holes and plate that would be easier to use.
megotatractor
Veteran Member
i get really angry every time I pull my mower deck! During summer I maybe pull the mower out bi-weekly or so to clean, sharpen and lube. And every time I lube the u-joints on the mower deck drive shaft I think about the engine to tranny shaft that is the same size that I can't get at. And I think about how after about 500 hours on the mower the driveshaft u-joints seem tight and new. Meanwhile the main tractor driveshaft that I neglected for lack of access had u-joint failure at 700 hours. If only I coulda lubed that thing I woulnd't have had to spend all those joyful hours in a heat wave repairing that driveshaft. So now at 750 hours am wishing I could lube it. My 2210 seems different from others, I am sure I've seen a post where someone removed the "service plug" on the left console and was able to see the ujoint? I open that plug and I see the driveshaft, but not the ujoint. I am thinking this is the weekend to remove the console cover and devise a way to create access with a larger service port or something! anything! Meanwhile I cannot even see the rear ujoint from ANY angle on this machine!!! A strategic hole may appear in the rear platform area!!