Results 11 to 16 of 16
-
02-22-2013, 06:12 PM #11Gold Member
- Join Date
- May 2012
- Posts
- 330
- Location
- West topsham VT
- Tractor
- Kioti DS3510
Re: Cutting torch questions
Originally Posted by psu927
Yes, but I had that with mine. I and my friend wound up with a glove of acetylene that ignited....was not fun but no damage done. If in doubt, rebuild it.
-
02-22-2013, 06:33 PM #12Elite Member
- Join Date
- Jan 2009
- Posts
- 2,717
- Location
- Figuring the picking points of jelly donuts.
- Tractor
- John Deere, 4200
Re: Cutting torch questions
Here is a really good video!
Cutting Torch - Tips for Oxygen Acetylene Cutting - YouTube
Miller Dynasty 300.
Lincoln V350-Pro w/pulse
LF-72
Lincoln SG Spool gun
Lincoln LN-25.
Everlast PowerArc 200.
5 Lincoln SA-200s.
1800 Ellis saw
Hypertherm Powermax 1250, CNC table.
PROFAX Welding Positioner.
JD2 model 3
-
02-22-2013, 07:58 PM #13Platinum Member
- Join Date
- May 2005
- Posts
- 969
- Location
- N. E. Florida
Re: Cutting torch questions
The neutral flame is the important part. Too much O2 is "Oxidizing flame" too actl is "Carborizing flame". You light the torch and dial back on O2, then bring it back up until the blue cone is perfect.
Also learn to use it with the gases fairly low rather than on higher than needed. Gas is expensive!!
Always know what is around you too. Many fires and explosions have been caused by poor torch handling.
Don't cut any vessel (barrel, tank, can) that you are not sure what is/was in it.
-
02-22-2013, 08:14 PM #14Gold Member
- Join Date
- Mar 2010
- Posts
- 449
- Location
- Nova Scotia
- Tractor
- B2620
Re: Cutting torch questions
I always turn the acetylene off first.Turning it off last will cause soot to contaminate the tip.
-
02-22-2013, 08:37 PM #15Member
- Join Date
- Dec 2010
- Posts
- 26
Re: Cutting torch questions
Good info guys thanks a bunch!!
-
02-22-2013, 10:19 PM #16Veteran Member
- Join Date
- Apr 2010
- Posts
- 1,911
- Location
- W Wisc
- Tractor
- Kubota L3130
Re: Cutting torch questions
Hard to beat irish Fixit's series on WW on torch use. He's an artist with it...
How to use a cutting torch - WeldingWeb™ - Welding forum for pros and enthusiasts-Dave
"Being a pessimist is great. You can't lose. Either you end up being right...or you are pleasantly surprised."
L3130HST, QA, 723 Loader, 48" Forks, 48" Grapple, Ancient Farmi Skidding winch
Trailer - 10k/16' twin axle w/elec brakes
2005 F250 5.4V8(3V) 3.73/4wd tow vehicle
Reply With Quote
Similar Threads
-
Cheap Cutting Torch?
By westbrooklawn in forum Build-It YourselfReplies: 29Last Post: 05-11-2010, 02:26 PM -
Victor Cutting Torch
By Jarrett in forum Build-It YourselfReplies: 17Last Post: 05-02-2007, 05:37 PM -
cutting torch under water
By Syncro in forum ProjectsReplies: 10Last Post: 05-02-2005, 11:18 PM -
Cutting Torch Tips.
By EdKing in forum Build-It YourselfReplies: 2Last Post: 08-13-2002, 06:24 AM -
cutting torch
By cj7 in forum ProjectsReplies: 5Last Post: 08-07-2002, 07:26 AM
