Page 2 of 2 FirstFirst 12
Results 11 to 13 of 13
  1. #11
    Veteran Member Mechanos's Avatar
    Join Date
    Aug 2010
    Posts
    1,042
    Location
    Roosterville, MO
    Tractor
    JD 955/70A/7 TLB

    Default Re: Tire Pressure with and without liquid ballast

    I jack up the whole *** end of the tractor, put a jackstand under the side I'm not working on to keep that tire off the ground. Then roll tire into position. Use the jack to raise or lower the side I am working on to get it aligned with the center hole of the wheel. Then put the trans in neutral and turn the axle shaft to align the bolt holes. Tighten the lug bolts down, then repeat the procedure for the other side. Work smarter... not harder...

  2. #12
    Super Star Member k0ua's Avatar
    Join Date
    Jun 2009
    Posts
    12,939
    Location
    Branson, Mo.
    Tractor
    Kioti DK35se Hydrostat

    Default Re: Tire Pressure with and without liquid ballast

    Quote Originally Posted by Mechanos View Post
    I jack up the whole *** end of the tractor, put a jackstand under the side I'm not working on to keep that tire off the ground. Then roll tire into position. Use the jack to raise or lower the side I am working on to get it aligned with the center hole of the wheel. Then put the trans in neutral and turn the axle shaft to align the bolt holes. Tighten the lug bolts down, then repeat the procedure for the other side. Work smarter... not harder...
    Wish I had thought of that back when I changed a flat on my old Long 2360 rear tire with CaCl in it. I got it done, but it was definately not in the "work smarter" classification. I dont know how much it weighed, but like others have said if it had ever fell over, I was not going to be able to push it up.

    James K0UA
    James KUA

    Kioti DK35se hydrostat with 2 QA buckets, 48 inch. King Kutter Rotary Cutter. 750 lbs ballast box. Loaded tires, Construction Attachments SSQA Lightweight Pallet forks. EA 50 inch single lid "wicked" Grapple. Satisfied Everlast PA160 welder owner How to add a link to a post . Best way to search TBN


  3. #13
    Platinum Member Furu's Avatar
    Join Date
    Nov 2009
    Posts
    608
    Location
    Washington
    Tractor
    JD 4720

    Default Re: Tire Pressure with and without liquid ballast

    Quote Originally Posted by Mechanos View Post
    I jack up the whole *** end of the tractor, put a jackstand under the side I'm not working on to keep that tire off the ground. Then roll tire into position. Use the jack to raise or lower the side I am working on to get it aligned with the center hole of the wheel. Then put the trans in neutral and turn the axle shaft to align the bolt holes. Tighten the lug bolts down, then repeat the procedure for the other side. Work smarter... not harder...
    I would imagine that even with the E-hydro transmission of Deere's that if in neutral that the rear axle shaft would free turn. That would make it so much easier. Now I just have to get a jack that can handle that much weight. My 4000 lb floor jack does not do both sides at once but I could do one side, jack stand it, then do the other and that should work. Definitely smarter way of doing it.
    JD 4720 - 400CX FEL, Woods BB-720 Brush Bull and BH90X backhoe, Salsco 6210XT PTO Chipper, Farmi 501 Logging Winch, Bo-Dozer Grapple, LP RBT4096, Cammond Road grader/leveler and Rankin Trash Forks

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2013 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.