Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Member
    Join Date
    Dec 2007
    Posts
    38
    Location
    hutchinson, ks
    Tractor
    toolcat plus many

    Default NEW PROBLEM STUCK IN (FNR)

    Cat was at idle I was out of the cab FNR lights was on when I got back in, it will not go off I turned unit off and will not restart because of this safety any ideas?

  2. #2
    Gold Member
    Join Date
    Sep 2003
    Posts
    358
    Location
    Central Idaho Mtns
    Tractor
    BX-23

    Default Re: NEW PROBLEM STUCK IN (FNR)

    I had this happen once. Short answer: I discon/connected the FNR switch/harness and traced the harness to ensure no shorts or fubar'd connector pins. Plugged everything back together and it worked.

    IIRC you can check the disconnected FNR switch with a simple continuity tester. If you have a service manual, you'll know which pins to probe right off the bat; otherwise, it's trial and error. (I have the SM but am presently at work.) What TC revision to you have ? (ie 'A'...'F') Also...I think my machine displayed a "code" when this happened.

  3. #3
    Member
    Join Date
    Dec 2007
    Posts
    38
    Location
    hutchinson, ks
    Tractor
    toolcat plus many

    Default Re: NEW PROBLEM STUCK IN (FNR)

    C model, I have no codes present so I am stumped

  4. #4
    Member MetroX's Avatar
    Join Date
    Nov 2006
    Posts
    34
    Location
    Milford, MI
    Tractor
    2004 Toolcat "B"

    Default Re: NEW PROBLEM STUCK IN (FNR)

    Sounds to me like the switch failed, and is stuck in the forward (or reverse) position. If I leave mine in either forward or reverse, it will not start.

  5. #5
    Gold Member
    Join Date
    Sep 2003
    Posts
    358
    Location
    Central Idaho Mtns
    Tractor
    BX-23

    Default Re: NEW PROBLEM STUCK IN (FNR)

    Looked in the SM and following are the pin functions on the "D" series FPR switch. I have no idea of there's a difference between the 'C' and 'D' in this area...
    Pin 1: 12V Switched, wire 1800
    Pin 2: One leg of the Hi Range/Low Range switch. (Wire 4960)
    Pin 3: One leg of the Hi Range/Low Range switch. Looks like it's internally wired to Pin 1.
    Pin 4: Reverse (Wire 4870)
    Pin 5: Park (Wire 4820)
    Pin 6: Forward. (Wire 4800)

    Those wires end up at the Drive Controller. Additionally the Park wire also goes to the Display Controller.

  6. #6
    Member
    Join Date
    Dec 2007
    Posts
    38
    Location
    hutchinson, ks
    Tractor
    toolcat plus many

    Default Re: NEW PROBLEM STUCK IN (FNR)

    Thanks Guys I will mess with it this weekend I do know that the park light is not on just FNR if I was to guess I expect that I will find a wire shorted exiting the cab.

  7. #7
    Member
    Join Date
    Dec 2007
    Posts
    38
    Location
    hutchinson, ks
    Tractor
    toolcat plus many

    Default Re: NEW PROBLEM STUCK IN (FNR)

    Found the problem KINDA!! Wire 1800 has no switched voltage!! Spudgunner,, where does wire 1800 get its power? I jumped 12v to the wire and got the machine put in the shop but don't know where it is suppose to come from it is not at the computer unless it changes number.

  8. #8
    Gold Member
    Join Date
    Sep 2003
    Posts
    358
    Location
    Central Idaho Mtns
    Tractor
    BX-23

    Default Re: NEW PROBLEM STUCK IN (FNR)

    Wire 1800 goes to some junction point that is supplied by wire 1430 which runs off of fuse #10 (15 Amp) in the cab. This fuse is "downstream" from a "switched power relay".

    The SM gets a little ambiguous on the route of the wire. It appears that other than the connector at the FPR switch, there is only the connector at what appears to be the fuse block and/or junction point previously mentioned.

  9. #9
    Member
    Join Date
    Dec 2007
    Posts
    38
    Location
    hutchinson, ks
    Tractor
    toolcat plus many

    Default Re: NEW PROBLEM STUCK IN (FNR)

    SPUDGUNNER THANKS I WILL LOOK AT IT AGAIN THIS WEEKEND AND POST!!!

  10. #10
    Member
    Join Date
    Dec 2007
    Posts
    38
    Location
    hutchinson, ks
    Tractor
    toolcat plus many

    Default Re: NEW PROBLEM STUCK IN (FNR)

    Didn't get to it,, try coming weekend!

Page 1 of 2 12 LastLast

Similar Threads

  1. B2400 starting problem finally solved
    By victor43 in forum Kubota Owning/Operating
    Replies: 47
    Last Post: 08-30-2013, 02:38 PM
  2. Power Steering Problem Not Solved
    By Alan L. in forum Kubota Owning/Operating
    Replies: 87
    Last Post: 03-31-2011, 07:35 PM
  3. KL130 on a CK30 Problem
    By tierbb in forum Kioti Owning/Operating
    Replies: 74
    Last Post: 11-20-2007, 04:06 PM
  4. For those with Starting Problem
    By Typhoon in forum New Holland Owning/Operating
    Replies: 22
    Last Post: 11-02-2006, 11:35 AM
  5. B2400 Starting Problem
    By victor42 in forum Kubota Owning/Operating
    Replies: 7
    Last Post: 06-03-2004, 08:13 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.