Hi! Fault codes for Bobcat, if somebody needs
Code Description
01-16 air filter Not connected
01-17 Clogged air filter
02-16 No hydraulic discharge filter is connected
02-17 Clogged Hydraulic Discharge Filter
03-09 Low battery voltage
03-10 High Voltage battery
03-11 Extremely high battery voltage
03-14 Extremely low battery voltage
03-22 The battery voltage is below the maximum permissible
04-09 Low oil pressure in the engine
04-14 Extreme hHibiscus oil pressure level in the engine
04-15 Engine oil pressure at emergency shutdown level
04-21 The oil pressure in the engine is above the maximum permissible
04-22 The oil pressure in the engine is below the maximum permissible
05-09 Low recharge pressure in the hydraulic system
05-14 Extremely low recharge pressure in the hydraulic system
05-15 Recharge pressure in the hydraulic system at the level of emergency shutdown of the engine
05-21 The recharge pressure in the hydraulic system is higher than the maximum
05-22 The recharge pressure in the hydraulic system is below the maximum permissible
06-10 High engine speed
06-11 Extremely high engine speed
06-13 No engine speed signal
06-15 Engine speed at the emergency shutdown level
06-18 Engine speed outside the permissible limits
07-10 High oil temperature in the hydraulic system
07-11 Extremely high oil temperature in the hydraulic system
07-15 Oil temperature in the hydraulic system at the level of emergency shutdown of the engine
07-21 The oil temperature in the hydraulic system is higher than the maximum permissible
07-22 The oil temperature in the hydraulic system is below the maximum permissible
08-10 High temperature of engine coolant
08-11 Extremely high engine coolant temperature
08-15 Engine coolant temperature at the emergency shutdown level
08-21 The coolant temperature of the engine is above the maximum permissible
08-22 The coolant temperature of the engine is below the maximum permissible
09-09 Low fuel level
09-21 The fuel level is above the maximum permissible
09-22 The fuel level is below the maximum permissible
11-05 The safety frame sensor is closed to the battery
11-06 The security frame sensor is closed to mass
12-21 Signal PWM Controller front additional. Hydraulics at the upper limit of the range
12-22 PWM Controller front additional. Hydraulics at the lower limit of the range
12-23 PWM Controller front additional. Hydraulics are not in a neutral position
13-05 The retaining solenoid of the fuel cutoff is closed on the battery
13-06 The retaining solenoid of the fuel cutoff is closed to the mass
13-07 Circuit Break solenoid cutoff fuel
14-02 Motorcyclist the fuel cutoff solenoid, erroneous switching on
14-03 Motorcyclist the fuel cutoff solenoid, erroneous shutdown
15-02 Motorcyclist solenoid lock thrust, erroneous inclusion
15-03 Motorcyclist solenoid lock thrust, erroneous shutdown
16-05 The holding solenoid lock is closed on the battery
16-06 The holding solenoid of the thrust lock is closed to the mass
16-07 Tearing chain restraint solenoid lock thrust
17-05 The hydraulic valve solenoid is closed to the battery
17-06 The hydraulic valve solenoid is closed to the mass
17-07 Rupture of the solenoid circuit of the hydraulic shutoff valve
18-05 The spool solenoid is closed on the battery
18-06 The spool solenoid is closed to the mass
18-07 Spool solenoid circuit break
19-02 Bucket positioning solenoid, erroneous switching on
19-03 Bucket positioning solenoid, erroneous shutdown
20-02 Speed switching solenoid, erroneous switching on
20-03 Speed switch solenoid, erroneous shutdown
21-02 Glow plugs, erroneous inclusion
21-03 Glow plugs, erroneous shutdown
22-02 Starter, erroneous inclusion
22-03 Starter, erroneous shutdown
23-02 Rear base solenoid, erroneous switching on
23-03 Rear base solenoid, erroneous shutdown
24-02 Rear Pull Solenoid, erroneous switching on
24-03 Rear Pull Solenoid, erroneous shutdown
25-02 Rear auxiliary proportional solenoid, erroneous inclusion
25-03 Rear auxiliary proportional solenoid, erroneous shutdown
26-02 Erroneous inclusion of the front base solenoid
26-03 Erroneous shutdown of the front base solenoid
27-02 Erroneous inclusion of the front Stock Solenoid
27-03 Erroneous shutdown of the front Stock Solenoid
28-02 Erroneous inclusion of solenoid Divertera
28-03 Incorrect solenoid shutdown Divertera
29-02 Large feed solenoid, erroneous switching on
29-03 Large feed solenoid, erroneous shutdown
30-28 Controller memory failure
31-28 Recovery mode failure
32-04 Advanced Management (ACS) is not reported to the controller Bobcat
32-23 ACS Advanced Management Not calibrated
32-31 Failure of the actuating mechanism of inclination
32-32 Malfunction of the electrical wiring of the actuating mechanism of inclination
32-33 Failure of the electrical wiring of the bucket tilting handle
32-34 Executive tilting mechanism not in neutral position
32-35 Handle/Bucket tilt pedal not in neutral position
32-36 Failure of the actuating mechanism of lifting
32-37 Malfunction of electrical wiring of the actuating mechanism of lifting
32-38 Failure of the electrical wiring of the boom handle
32-39 Executive lifting mechanism not in neutral position
32-40 Arm/Boom lift pedal not in neutral position
32-41 No connection
32-49 Executive lifting mechanism closed to mass
32-50 The executive tilting mechanism is closed to mass
32-51 Actuator lifting mechanism closed on the battery
32-52 The actuator tilting mechanism is closed to the battery
32-53 Handle/Boom lift pedal closed to mass
32-54 Handle/Bucket tilt pedal closed to mass
32-55 Arm/Boom lift pedal closed on battery
32-56 The handle/bucket tilt pedal is closed to the battery
32-57 Reduced performance of the lifting actuation mechanism
32-58 Reduced performance of the executive tilt mechanism
32-59 Wrong direction of the actuating mechanism of lifting
32-60 Wrong direction of the executive tilt mechanism
32-61 The lock of arms is closed to mass
32-62 The lock of Arms is closed on the battery
32-63 The chain of locking pedals is closed to the mass
32-64 The chain of locking pedals is closed to the battery
32-65 Sensor supply voltage outside the permissible limits
32-66 Battery voltage out of the allowable limits
32-67 Switched during Operation
32-68 Boom Boom ARM Information error
32-69 The switch of control modes has switched during operation
32-70 The chain of the right handle of motion is closed to mass
32-71 Circuit of the right handle of movement is closed on the battery
33-23 Main controller (Controller Bobcat) Not programmed
34-04 The keypad with a button run is not reported to the controller Bobcat
35-02 Speed fan switch, erroneous switching on
35-03 Speed fan switch, erroneous shutdown
36-48 Multiple ACD controllers are connected
37-02 Speed additional speed switch, erroneous switching on
37-03 Speed additional speed switch, erroneous shutdown
Bobcat Medium-S630
Bobcat Medium-S630
38-04 No connection to Joystick controller
38-05 The x-axis of the left joystick is not in a neutral position
38-06 The X-axis of the right joystick is not in a neutral position
38-07 The Y-axis of the left joystick is not in a neutral position
38-08 The Y-axis of the right joystick is not in a neutral position
38-09 Control mode switch-circuit to the battery or to the mass
38-11 Executive lifting mechanism not in neutral position
38-12 Executive tilting mechanism not in neutral position
38-13 Failure of the actuating mechanism of lifting
38-14 Failure of the actuating mechanism of inclination
38-15 Right Wheel speed control failure
38-16 Faulty wiring for the speed of the left wheel
38-17 Reduced performance of the executive tilt mechanism
38-18 Reduced performance of the lifting actuation mechanism
38-19 The X-axis of the left joystick, behind the upper bound of the range
38-20 X-axis of the right joystick, beyond the lower bound of the range
38-21 The Y-axis of the left joystick, behind the upper bound of the range
38-22 The Y-axis of the right joystick, behind the upper bound of the range
38-23 Signal of the front right control sensor outside the upper boundary of the range
38-24 Signal of the front left control sensor at the upper limit of the range
38-25 Signal of the rear right control sensor at the upper limit of the range
38-26 Signal of the rear left control sensor at the upper limit of the range
38-27 Signal of the actuating mechanism of lifting at the upper boundary of the range
38-28 Signal of the executive mechanism of inclination at the upper boundary of the range
38-29 X-axis of the left joystick, behind the lower bound of the range
38-30 X-axis of the right joystick, beyond the lower bound of the range
38-31 Y-axis of the left joystick, beyond the lower bound of the range
38-32 Y-axis of the right joystick, beyond the lower bound of the range
38-33 Signal of the front right control sensor at the lower limit of the range
38-34 Signal of the front left control sensor at the lower limit of the range
38-35 Signal of the rear right control sensor at the lower limit of the range
38-36 Signal of the rear left control sensor at the lower limit of the range
38-37 Power supply “1” 5-volt sensor, behind the lower boundary of the range
38-38 Power supply “2” 5-volt sensor, behind the lower boundary of the range
38-39 Executive lifting mechanism closed to mass/beyond the lower boundary of the range
38-40 The executive tilt mechanism is closed to the mass/signal at the lower limit of the range
38-41 Wrong direction of the executive tilt mechanism
38-42 Wrong direction of the actuating mechanism of lifting
38-43 The solenoid of the left front drive, erroneous switching on
38-44 Solenoid of left reversible drive, erroneous switching on
38-45 Right front drive solenoid, erroneous switching on
38-46 Right reverse actuator solenoid, erroneous switching on
38-47 Front right control solenoid, erroneous switching on
38-48 Front left solenoid control, erroneous switching on
38-49 Rear right control solenoid, erroneous switching on
38-50 Rear left solenoid control, erroneous switching on
38-51 Control system pressure solenoid, erroneous switching on
38-52 Reversing signal, erroneous switching on
38-53 Left Front drive solenoid, erroneous shutdown
38-54 Solenoid of left reversible drive, erroneous shutdown
38-55 Right front drive solenoid, erroneous shutdown
38-56 Right reverse actuator solenoid, erroneous shutdown
38-57 Front right extension control solenoid, erroneous shutdown
38-58 Front right retraction control solenoid, erroneous shutdown
38-59 Front left solenoid of extension control, erroneous shutdown
38-60 Front left solenoid control retraction, erroneous shutdown
38-61 Rear right extension control solenoid, erroneous shutdown
38-62 Rear right retraction control solenoid, erroneous shutdown
38-63 Rear left solenoid control, erroneous shutdown
38-64 Rear left solenoid control retraction, erroneous shutdown
38-65 Control system pressure solenoid, erroneous shutdown
38-66 Reversing signal, erroneous shutdown
38-67 No messages from controller Bobcat
38-68 Wheel setting angles (alignment) not calibrated
38-69 actuating mechanisms of lifting and tilting are not calibrated
38-70 Power off
38-71 Battery voltage outside the permissible limits
38-72 Drive Pump Not calibrated
38-73 Control/Motion mode switch is switched on during operation
38-74 Speed of the uncontrolled right wheel, erroneous switching on
38-75 Speed of uncontrolled left wheel, erroneous switching on
38-76 Control system pressure solenoid-insufficient current
38-77 Front right extension control solenoid-insufficient current
38-78 Front right retraction control solenoid-insufficient current
38-79 Forward left solenoid of extension control-insufficient current
38-80 Front left solenoid control retraction-insufficient current
38-81 Rear right extension control solenoid-insufficient current
38-82 Rear right retraction control solenoid-insufficient current
38-83 Rear left solenoid control-insufficient current
38-84 Rear left solenoid control retraction-insufficient current
38-85 Power supply “1” 5-volt sensor outside the upper boundary of the range
38-86 Power supply “2” 5-volt sensor outside the upper boundary of the range
38-87 Right front wheel lock (mechanical malfunction control)
38-88 Locking of the Left front wheel (mechanical malfunction control)
38-89 Right rear wheel lock (mechanical malfunction control)
38-90 Rear left control error
38-91 There are no pulses of the right wheel speed sensor
38-92 There are no pulses of the left wheel speed sensor
38-93 Right wheel speed sensor does not respond
38-94 The left wheel speed sensor does not respond
38-98 Controller in the drive calibration mode
38-99 Controller in wheel position calibration mode
45-03 Right turn pointer, erroneous shutdown
46-02 Left turn pointer, erroneous inclusion
46-03 Left turn pointer, erroneous shutdown
47-21 Power supply of 8-volt sensor at the upper limit of the range
47-22 Power supply of 8-volt sensor, behind the lower boundary of the range
48-02 Front light relays, erroneous switching on
48-03 Front light relay, erroneous shutdown
49-02 Rear light relay, erroneous switching on
49-03 Rear light relay, erroneous shutdown
60-21 Signal of the control lever of the back additional Hydraulics at the top of the range
60-22 Signal of the control lever of the back additional Hydraulics at the lower limit of the range
60-23 Control lever of the back additional The hydraulics are not returned to the neutral position
64-02 Failure to turn on the power relay
64-03 Erroneous shutdown of power relay
74-72 Controller boot code failed Bobcat
74-73 Left panel, receiving device error
80-02 ACD, Exit “A”, erroneous switching on
80-03 ACD, Exit “A”, erroneous shutdown
81-02 ACD, Output “B”, erroneous switching on
81-03 ACD, Exit “B”, erroneous shutdown
82-02 ACD, Exit “C”, erroneous inclusion
82-03 ACD, Exit “C”, erroneous shutdown
83-02 ACD, Exit “D”, erroneous switching on
83-03 ACD, Exit “D”, erroneous shutdown
84-02 ACD, Output “E”, erroneous switching on
84-03 ACD, Exit “E”, erroneous shutdown
90-02 Service exit “C”, erroneous switching on
90-03 Service exit “C”, erroneous shutdown
91-02 Service exit “D”, erroneous switching on
91-03 Service exit “D”, erroneous shutdown
92-02 Service exit “E”, erroneous inclusion
92-03 Service Output “E”, erroneous shutdown
93-02 Service exit “F”, erroneous switching on
93-03 Service exit “F”, erroneous shutdown
