Results 41 to 50 of 66
-
04-02-2013, 06:15 PM #41
Re: Update on my Stickweld 250
Hi Guys,
Whatever the issue we will take care of it. We have been slammed with preparing for the new website launch so I apologize for not being here rather quickly, but we can take a look at any unit, and get something going as a fair solution. Thank you all.
-
04-02-2013, 06:22 PM #42
Re: Update on my Stickweld 250
-
04-02-2013, 06:24 PM #43
-
04-02-2013, 06:43 PM #44
Re: Update on my Stickweld 250
I had sent a message to the main longevity account, incase you didn't get it, here is the run down.
I just figured out the machine you guys sent me is defective. I didn't know what arc force really did, so I had no way to know. Anyways, the arc force does absolutely nothing. No matter the setting, 6011 on the 6010 port has a bone dry puddle. I mean dry to the point that you loose the puddle with each whip and pause. 7018 on the normal port is like water. Very flowy puddle, but impossible to manage at any kind of an angle. Also, no matter what I did, I couldn't get a distinct puddle. Even on the old AC tombstone, you got a very clear and distinct puddle. I didn't play around with the amps too much, but it was really clear it couldn't push the slag back, and let me see the puddle.
There is clearly something wrong, but since I had used the 6010 port maybe once, I didn't notice it. (and yes I did try the 6011 on the normal port, it didn't run well, but the puddle was like water as well) Let me know what you can do, I am really wanting to get some practice in, and I have realized this will make it way harder..Never carry gasoline in your car trunk. If you do, atleast use some sort of container.
-red green
-
04-02-2013, 06:46 PM #45
Re: Update on my Stickweld 250
Deereman,
Give David a call today if you can. He can try several things to see what can be done. We can always replace it for you as well.
-
04-02-2013, 06:49 PM #46
-
04-02-2013, 07:00 PM #47
Re: Update on my Stickweld 250
deereman when you get it all straightened out, Furu's machine loves ESAB's 10P-Plus 6010. All you have to do is hold a close arc length, set the arc force on 7 1/2 (I think, check with Furu) no problem getting the stack of dimes look!
-
04-03-2013, 02:00 AM #48
-
04-03-2013, 08:11 AM #49
Re: Update on my Stickweld 250
Ok, thanks Simon. Always nice dealing with you.
Never carry gasoline in your car trunk. If you do, atleast use some sort of container.
-red green
-
04-03-2013, 06:33 PM #50
Re: Update on my Stickweld 250
Just got off the phone with longevity tech support, they are sending me a shipping label and a forum to fill out. It is going back for repair. Let's hope this works.
Never carry gasoline in your car trunk. If you do, atleast use some sort of container.
-red green
Similar Threads
-
StickWeld 250 Torture Test + Full Review (Video and Write-Up)
By ChuckE2009 in forum WeldingReplies: 6Last Post: 01-25-2013, 08:19 AM -
StickWeld 250 Video Part 1 from Lanse on Youtube
By LONGEVITYsimon in forum WeldingReplies: 10Last Post: 11-29-2012, 01:39 PM -
Got a new StickWeld 250!!
By ChuckE2009 in forum WeldingReplies: 2Last Post: 11-28-2012, 01:41 PM -
My Stickweld 250 Review
By Furu in forum WeldingReplies: 4Last Post: 05-21-2012, 07:33 PM -
Longevity's Stickweld 250 / my review.
By Shield Arc in forum WeldingReplies: 30Last Post: 05-20-2012, 07:20 PM