Results 1 to 9 of 9
  1. #1
    Bronze Member psvfd's Avatar
    Join Date
    Dec 2010
    Posts
    66
    Location
    SE Louisiana
    Tractor
    Yanmar 2010

    Default YM2010 rear wheel lug size

    I am planing to remove the rear wheels to work on the brakes. I need to know the size wrench I will need. I am 2 1/2 hours from where I keep the tractor and I did not check the size last weekend when I was there.
    Can anyone help me with the size? I was not planing to a brake job yet but when I wanted to cut brush last weekend the right side tire would not move. I removed the cover plate and shoes and it is a rusted mess. I have the covers off both sides and I need to clean the drums. It was hard enough to pull with the wheels on I figure it will not be as bad with the wheels off. I will be using a 2 1/4 ton floor jack and 6 ton jack stands. Is that good for this job?
    Rene' Bowers



    ______________________
    Yanmar 2010
    4' cutter
    4' box
    4' rake
    boom lift pole

  2. #2
    Gold Member
    Join Date
    Jul 2008
    Posts
    447
    Location
    20 miles west of Atlanta
    Tractor
    Yanmar 2210BD

    Default Re: YM2010 rear wheel lug size

    Jack and stands are plenty strong enough. If there are two of you there you can jack in the middle of the rear chunk to the point it teeters, just high enough to remove the tires. Let one tire touch the ground, put stand under the one off the ground, teeter it on the stand the put the other stand in place. Lower jack. One man can do this, just may take a couple of extra pumps on the jack. Lug nuts, at least 7/8 not sure of mm but if you take 7/8 and 1" and hopefully the equal in mm you should be ok.
    Try not. Do or do not. There is no try. Yoda

  3. #3
    Super Member clemsonfor's Avatar
    Join Date
    Sep 2009
    Posts
    6,147
    Location
    Greenwood Co., SC
    Tractor
    Yanmar YM2000

    Default Re: YM2010 rear wheel lug size

    Tractor weighs 2000lb jack us rated at 5000lb your good even if you wanna lift the whole thing.
    same with stands there rated at 12000lbs so the whole tractor can be on one. They may be a little tall though, but will work.
    YM2000. MF dirt scoop,4' Jbar bushhog,boompole, LMC 12-16 disk harrow, 4' Atlas boxblade (with rippers). 1980 chevy K10,1990 ford ranger 2wd (285K miles),1997 saturn SL2 (twin cam!!),2001Toyota Higlander
    1986 Cobia 177 sunskiff w/1981 Johnson 60 hp
    1991 Javalen 17ft w/same year 150 Johnson GT
    Troybuilt 4 cycle & Echo 2 stroke,cold natured(need carb rebuild),MS390 Stihl, Northern tool pressure washer, mixes water into the oil in the pump(now dead, motor on a tiller). 5000 watt generator.

  4. #4
    Bronze Member psvfd's Avatar
    Join Date
    Dec 2010
    Posts
    66
    Location
    SE Louisiana
    Tractor
    Yanmar 2010

    Default Re: YM2010 rear wheel lug size

    Got the brakes back in today. I had to use a 1 1/16 socket, it fit just a little loose. Looks like I needed a 26mm. The jack stands were ok almost too wide at the base but just did fit.
    Thanks for the replies.
    Attached Thumbnails Attached Thumbnails -dsc00864-jpg   -dsc00865-jpg  
    Rene' Bowers



    ______________________
    Yanmar 2010
    4' cutter
    4' box
    4' rake
    boom lift pole

  5. #5
    Gold Member
    Join Date
    Jul 2008
    Posts
    447
    Location
    20 miles west of Atlanta
    Tractor
    Yanmar 2210BD

    Default Re: YM2010 rear wheel lug size

    Sorry to take so long on the socket size but if you ever need it my lugnuts are 15/16 / 24mm.
    Try not. Do or do not. There is no try. Yoda

  6. #6
    Super Member clemsonfor's Avatar
    Join Date
    Sep 2009
    Posts
    6,147
    Location
    Greenwood Co., SC
    Tractor
    Yanmar YM2000

    Default Re: YM2010 rear wheel lug size

    Quote Originally Posted by ninefinger View Post
    Sorry to take so long on the socket size but if you ever need it my lugnuts are 15/16 / 24mm.
    15/16 is 1/8 smaller, i cant beleive he got it off with the 1 1/16!
    YM2000. MF dirt scoop,4' Jbar bushhog,boompole, LMC 12-16 disk harrow, 4' Atlas boxblade (with rippers). 1980 chevy K10,1990 ford ranger 2wd (285K miles),1997 saturn SL2 (twin cam!!),2001Toyota Higlander
    1986 Cobia 177 sunskiff w/1981 Johnson 60 hp
    1991 Javalen 17ft w/same year 150 Johnson GT
    Troybuilt 4 cycle & Echo 2 stroke,cold natured(need carb rebuild),MS390 Stihl, Northern tool pressure washer, mixes water into the oil in the pump(now dead, motor on a tiller). 5000 watt generator.

  7. #7
    Bronze Member psvfd's Avatar
    Join Date
    Dec 2010
    Posts
    66
    Location
    SE Louisiana
    Tractor
    Yanmar 2010

    Default Re: YM2010 rear wheel lug size

    I could not get the 1 inch socket to fit that is why I had to use the 1 1/16. Is mine just different, I measured the head of the bolts with my vernier caliper as 1.015 inches.
    Rene' Bowers



    ______________________
    Yanmar 2010
    4' cutter
    4' box
    4' rake
    boom lift pole

  8. #8
    Gold Member
    Join Date
    Jul 2008
    Posts
    447
    Location
    20 miles west of Atlanta
    Tractor
    Yanmar 2210BD

    Default Re: YM2010 rear wheel lug size

    I do not have a caliper, just fit the sockets on and they were a good fit. I guess all these same model creatures have some differences. Did you have to replace the shoes or just clean everything up?
    Try not. Do or do not. There is no try. Yoda

  9. #9
    Bronze Member psvfd's Avatar
    Join Date
    Dec 2010
    Posts
    66
    Location
    SE Louisiana
    Tractor
    Yanmar 2010

    Default Re: YM2010 rear wheel lug size

    I just cleaned everything up, the shoes still had a lot of lining on them.
    Rene' Bowers



    ______________________
    Yanmar 2010
    4' cutter
    4' box
    4' rake
    boom lift pole

Similar Threads

  1. Toolcat 5610 vs CUT review
    By radman1 in forum Buying/Pricing/Comparisons
    Replies: 18
    Last Post: 08-29-2013, 03:50 PM
  2. rear wheel for brush hog
    By defed in forum Customization
    Replies: 37
    Last Post: 03-15-2012, 02:42 AM
  3. YM2210 Rear Blade Size
    By broncobisley1 in forum Yanmar
    Replies: 13
    Last Post: 09-06-2010, 12:58 PM
  4. Kubota rear wheel lug pattern
    By BTackett in forum Kubota Owning/Operating
    Replies: 0
    Last Post: 03-12-2008, 01:05 PM
  5. Front wheel lug bolt size TC40DA?
    By lhfarm in forum New Holland Owning/Operating
    Replies: 5
    Last Post: 10-30-2007, 10:00 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2013 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.