Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 21
  1. #11
    Veteran Member CliffordK's Avatar
    Join Date
    Mar 2013
    Posts
    1,202
    Location
    Eugene, Oregon
    Tractor
    Toro D200, Ford 1715, International 884,

    Default Re: Front drive case schematic?

    Looking at the diagram, the shift arm doesn't look that complicated, although it does look like it has splines on it, and a couple of other pieces. What happened to yours?

    Could it be repaired, or a new one be made?

    Do you have photos of the piece?

  2. #12
    Elite Member
    Join Date
    Dec 2009
    Posts
    2,675
    Location
    gilmer tx
    Tractor
    yanmar 2002d

    Default Re: Front drive case schematic?

    Here is a good picture of 284 internationals. He is probably an expert on them. http://www.tractorbynet.com/forums/y...y-trouble.html

  3. #13
    Gold Member stormpetrel's Avatar
    Join Date
    Oct 2010
    Posts
    344
    Location
    Block Island R.I.
    Tractor
    ym2210D

    Default Re: Front drive case schematic?

    Mine looks a little different, but it's been a while since I've seen it. I've been using the tractor w/just 2wd. I don't want to take it apart until I've secured another one to replace it with....although it may be fixable I guess.

  4. #14
    Super Member California's Avatar
    Join Date
    Jan 2004
    Posts
    5,658
    Location
    Sonoma County
    Tractor
    Yanmar YM240, YM186D, and another YM186D

    Default Re: Front drive case schematic?

    Stormpetrel if your part is simply bent like 284's was, I expect a blacksmith could reshape it back to like new.

  5. #15
    Gold Member stormpetrel's Avatar
    Join Date
    Oct 2010
    Posts
    344
    Location
    Block Island R.I.
    Tractor
    ym2210D

    Default Re: Front drive case schematic?

    Quote Originally Posted by California View Post
    Stormpetrel if your part is simply bent like 284's was, I expect a blacksmith could reshape it back to like new.
    I sure would like to have the 4wd back..maybe I'll just take it apart again (as long as the tranny is drained for the PTO cover fiasco) and try. I did find a place (courtesy of Kenmac) whose website said they have the part! I emailed 'em Fri. evening and haven't heard back yet.

  6. #16
    Veteran Member CliffordK's Avatar
    Join Date
    Mar 2013
    Posts
    1,202
    Location
    Eugene, Oregon
    Tractor
    Toro D200, Ford 1715, International 884,

    Default Re: Front drive case schematic?

    You might look at your tractor to see if you could make a cover plate over where the transfer case goes.

    So, while you're tinkering on the transfer case, you could be driving the tractor.

  7. #17
    Platinum Member
    Join Date
    Oct 2002
    Posts
    741
    Location
    Pomfret,Connecticut
    Tractor
    yanmar 336d w ldr,C,Cub,many attachments

    Default Re: Front drive case schematic?

    i had one made up for the 336,looks alot like what you need, take the old one to a machine shop,they might just surprise you...

  8. #18
    Gold Member stormpetrel's Avatar
    Join Date
    Oct 2010
    Posts
    344
    Location
    Block Island R.I.
    Tractor
    ym2210D

    Default Re: Front drive case schematic?

    Quote Originally Posted by CliffordK View Post
    You might look at your tractor to see if you could make a cover plate over where the transfer case goes.

    So, while you're tinkering on the transfer case, you could be driving the tractor.
    Wow, that's a cool idea!! I don't know if I want to mess with almost 5 gallons of hydraulic fluid to change the cover back to the drop box again.......

  9. #19
    Gold Member stormpetrel's Avatar
    Join Date
    Oct 2010
    Posts
    344
    Location
    Block Island R.I.
    Tractor
    ym2210D

    Default Re: Front drive case schematic?

    I received the pto cover. I took the old one off....whew! There are two linkages with pins holding the PTO and plate in the transmission you must remove (along with teeeny lil cotter pins) before the pto assembly will come out more than an inch and a half......so more disassembly than I thought was necessary. I switched the pto gears to the new plate, it's ready to go back in. I am not looking forward to getting the pins back in, there is NO room. I guess I'll go for the harder of the two first. If I drop the pin I can just remove the whole assembly and try again.

    The inside of the tranny looks quite nice; the fluid is clean and there are no metal shavings to be found

    Now on to the shift lever. I ordered all new seals because I reused the old ones last time and it leaks. It's a fairly straightforward job to remove the dropbox and get at the shift lever. I sure wish I had a new one to look at to have an idea of what needs to be done to fix it. I never heard back from the European/Middle Eastern website that had the shift lever in stock according to their search results..............

  10. #20
    Super Member kenmac's Avatar
    Join Date
    Feb 2005
    Posts
    5,713
    Location
    The Heart of Dixie
    Tractor
    yanmar 3110D

    Default Re: Front drive case schematic?

    Quote Originally Posted by stormpetrel View Post
    I sure wish I had a new one to look at to have an idea of what needs to be done to fix it. I never heard back from the European/Middle Eastern website that had the shift lever in stock according to their search results..............
    I have e mailed jeepsea several times trying to get a response. I have gotten nothing.sorry I got your hopes up .Good luck with the repair
    Yanmar 3110D
    07 Dodge 2500 5.9 Cummins
    Husky 372xp
    Husky 55 Rancher
    Maruyama trimmer
    Husky trimmer
    Redmax BP blower
    Toro zero turn
    North Star 4 K PSI pressure washer
    Honda 300 4 trax
    Yamaha Timberwolf
    liquid logic coupe kayak
    16' Tow Master Dump Trailer ,20' Yanmar Hauler

Page 2 of 3 FirstFirst 123 LastLast

Similar Threads

  1. Replies: 3
    Last Post: 10-05-2012, 07:32 AM
  2. L3130 4 wheel drive axle case
    By prostock in forum Parts/Repairs
    Replies: 0
    Last Post: 08-20-2012, 12:47 PM
  3. 2800/3400 gear drive - pto lever schematic
    By bigballer in forum Kubota Owning/Operating
    Replies: 2
    Last Post: 08-03-2012, 09:36 AM
  4. Case J48 mule drive parts
    By sparkey in forum Parts/Repairs
    Replies: 0
    Last Post: 06-27-2012, 03:54 PM
  5. 3054 front drive case shift fork
    By Yard Slave in forum Kioti Owning/Operating
    Replies: 0
    Last Post: 04-06-2008, 12:09 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.