Page 4 of 4 FirstFirst 1234
Results 31 to 34 of 34
  1. #31
    Super Member clemsonfor's Avatar
    Join Date
    Sep 2009
    Posts
    6,468
    Location
    Greenwood Co., SC
    Tractor
    Yanmar YM2000

    Default Re: YM 1700 cylinder sleeve

    Never pulled liners but have pulled a few harmonic ballencers and flywheels on boats and such and the constant pressure, spray lube and a whack of a hammer every now and then seeme to what finiallly "pops" them free.

    I had a boat flywheel that i was scared i was going to damage the crank pulling any harder than i had it, so i let it sit, sparyed it again and tapped it a buch with a hammer. Then the second or third day i got home gave it a whack and ping it popped free.
    YM2000. MF dirt scoop,4' Jbar bushhog,boompole, LMC 12-16 disk harrow, 4' Atlas boxblade (with rippers). 1980 chevy K10,1990 ford ranger 2wd (285K miles),1997 saturn SL2 (twin cam!!),2001Toyota Higlander
    1986 Cobia 177 sunskiff w/1981 Johnson 60 hp
    1991 Javalen 17ft w/same year 150 Johnson GT
    Troybuilt 4 cycle & Echo 2 stroke,cold natured(need carb rebuild),MS390 Stihl, Northern tool pressure washer, mixes water into the oil in the pump(now dead, motor on a tiller). 5000 watt generator.

  2. #32
    Elite Member Car Doc's Avatar
    Join Date
    Mar 2009
    Posts
    3,246
    Location
    Kansas
    Tractor
    YM3810D Yanmar

    Default Re: YM 1700 cylinder sleeve

    Last motor I replaced liners on was a Ford industrial 3 cyl gasser 201ci (or something about that size) in a Davis trencher did them in frame. Anyway they were pretty big cylinders made it easy to weld inside of. I worked my rear off on them with a plate I made that fit the bottoms real nice and finally mig welded some large lug nuts about half way down inside the liners and pounded them up from the bottom. Once I got them moving they went real easy went back in nice too.
    Last edited by Car Doc; 06-10-2013 at 04:02 PM. Reason: wrong engine size and make of trencher bad memory
    Yanmar YM3810D, LT duty 3pt hoe, 6' KK2 tiller, 6' KK box blade, 6 1/2' KK disc, 5' Howse bush hog, 5' Howse back blade, 9" Yellow PHD, 3 Husky chain saws 346XP NE, 359, 372XP. 07 HD Heritage Softail, Crack injectors, check compression, take 2 beers and call me. "Hey you didn't build that."

  3. #33
    New Member
    Join Date
    Jun 2013
    Posts
    7
    Location
    Poetry, Tx
    Tractor
    Yanmar 2200 and 336D

    Default Re: YM 1700 cylinder sleeve

    I'm in process on a full rebuild of my 336d. It had set in my yard since 2007 and somewhere else before that. Lots of rust inside everywhere except the rod and main journals. I pulled the liners yesterday using a piece of 3" pipe and a hammer. The block is completely stipped down and on the floor so it made it easy.

  4. #34
    New Member
    Join Date
    Dec 2013
    Posts
    10
    Location
    Ventura CA
    Tractor
    Yanmar ym155d

    Default Re: YM 1700 cylinder sleeve

    hi
    I just pulled (?) the sleeves on a ym155d and it was the worst job I have done in a long time. The puller was like those shown on this site, but even with ice and heating the block with a dryer it wont budge. I found that the only way to get them to move was to add tension on the puller and then hit the sleeve from the bottom with a piece of steel and a sledge hammer. Your consolation will be that you will be getting out and under the tractor at least 50 times so you can forget your sit ups for a week after.
    Tired Gpa Bill

Page 4 of 4 FirstFirst 1234

Similar Threads

  1. Replies: 15
    Last Post: 03-18-2013, 11:04 PM
  2. cylinder sleeve removal
    By tgathright in forum New Holland Owning/Operating
    Replies: 13
    Last Post: 01-06-2012, 11:22 AM
  3. Small weld on cylinder sleeve
    By cgraham in forum Hydraulics
    Replies: 14
    Last Post: 07-05-2007, 04:28 PM
  4. Cylinder sleeve removal?
    By CO_Farmer in forum Yanmar
    Replies: 2
    Last Post: 01-16-2006, 02:02 PM
  5. 1700 series 2 cylinder desiel iseki
    By wlwmo in forum Parts/Repairs
    Replies: 1
    Last Post: 08-10-2003, 08:10 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.