Recent content by claggstractors

  1. C

    MX5100 injection pump failure

    Spencer Diesel out of Iowa. Spencer Diesel. Premier rebuilder of pumps, turbos, and injectors. Sometimes you get lucky with them and they have a rebuilt one on the shelf already. I've only been it at it for half the time, but I've replaced more pumps the last 5 years then the 15 before that.
  2. C

    Tym part numbers

    Private Message me your email and I can email you a copy of the parts catalog. It's not formatted correctly, has all the odd numbered pages first then all even numbered pages. So basically you have to write down your figure number and the number for the part in the figure, then go towards the...
  3. C

    MF 431 - Injection pump problem? - sat and then fires off to high rpm

    Fourth sentence he states he tried starting it without doing anything. Then he checked out the fuel supply. Once that was fixed, it started but was going beyond governed RPMs. I thought it was the governor that was stuck, but @thepumpguysc pointed out that it was the metering valve. Learned...
  4. C

    MF3165: Help determining what type of clutch to buy

    May want to try Shop AGCO Parts . Hopefully they got it all broke down by type and serial number there, otherwise it will be a split and find out situation.
  5. C

    MF 431 - Injection pump problem? - sat and then fires off to high rpm

    Also, don't forget to pull the timing pin before reassembly. @Jason1010 I got a copy of the Perkins manual in case you need it.
  6. C

    Considering a TYM T264

    Had to look that one up but looks like a nice unit. Can't say the little LS's were ever very troublesome. First one that came into the shop was purple and branded LandTrac. That was about 20 years ago. Looks like it will be a little more capable all around than the T264.
  7. C

    First electric tractor ride

    Then why would they have a dealer in Maine?
  8. C

    MF 431 - Injection pump problem? - sat and then fires off to high rpm

    Yeah, sometimes it takes a while if a piece is really stuck and sometimes no matter what the pump has to pulled and gone over. I've always hated how Perkins set these up though.
  9. C

    First electric tractor ride

    Yeah, instead it's ten degrees out and will void the warranty to even use it. 14F Minimum operating temp lol
  10. C

    First electric tractor ride

    Was wondering where they were actually made and it wasn't mentioned in the About Us section. Looked through the News section and the angle of the photo showed the FarmTrac logo. Good luck selling them where ever there was FarmTrac dealers that got left high and dry. Pretty screwed up what...
  11. C

    2022 L3302

    Man, that is rough. Probably not a bad idea to check all the fluids, and look over it for any rubbing hoses and such. Sounds the prep work for sale is more than lacking.
  12. C

    MF 431 - Injection pump problem? - sat and then fires off to high rpm

    OK, yeah, think you have a pretty good chance of getting it unstuck though. I had at least 3 of them in TYMs do the same thing and it worked. Perkins made these really "fun" to r&r injection pumps on. Pretty good little engines though.
  13. C

    MF 431 - Injection pump problem? - sat and then fires off to high rpm

    I've had some luck with using either Stanadyne or ATF in freeing up stuck items in the injection pumps on these. Have had to replace a couple though on rather low hour TYM's that used that pump on the Perkins 1103 & 1104. Does yours have the fuel lift pump built into the fuel filter housing too...
  14. C

    2810 clutch issues.

    Yeah, the original 10/20 Series Bransons are very good little tractors. Parts support and pricing was better when Americans were running the distribution side of things. Same thing happened at TYM though too. Both companies can make some really good product. But seems to be they keep rushing...
  15. C

    2810 clutch issues.

    No problem. Thanks to Asteral for pulling them out of Branson though. Otherwise, you would have had to waited for me to scan the needed pages out of the paper manual lol.
Top