Recent content by Danner

Seriously looking to get a B2601 with BH, FEL, & MMM. My BX2660 is a 2011 with about 550 hours on it, with FEL and 54" MMM, all in rather good shape, stored indoors, maintained, etc. So, I could trade it in, which would get me minimum $$$, or I could post it in the classifieds (maximum $$$?)...

I've had the 2660 for about 5 years, mowing mostly (54"MMM), but also building and maintain gravel driveways (FEL & box blade), general FEL work, and a little brush hog work with 48" LandPride on the PTO. So, I will be building a new home next year, I run HAM radio antenna lines and have...

Wanting to put in a garden this spring, I am looking for advice on which rotary tiller to run off the PTO of my BX2660? My other implements are LandPride, by they don't seem to carry tillers. Also, wonder if I should go forward or reverse rotation of the tiller? I value quality/reliability...

Would it be a reasonable project to use my BX2660, the FEL, and a 48" LandPride box blade to dig a pond about 80 feet in diameter, and maybe 15 feet deep? It's flat are near the creek, and the soil is black clay without significant rocks. I was thinking I could tilt the box blade to the max...

Cut about 4 acres today, and when I parked the 2660 (270 hours on the clock), there was a puddle of hyd-oil under the front end. Turns out, one of the line to the steering cylinder rubbed the side of the engine and sprung an abrasion leak. The part will be a hose assembly, but getting to the...

BX spreader questions seem to come up, so I thought I'd share my new set-up. This is the Model I-92 electric spreader on a BX2660. The electrical box and on/off and a speed control rheostat. I put the box together. Have not spread anything yet. Power comes from the extra circuit at the back...

I am going to cultivate and plant 5 acres of Bermuda hay this next spring. As a look for someone to come in to mow and square bale, what is a fair share of the produce? Also, would it be better if I mowed it? Thanks.

I have about 4 ac. of pasture that has been uncultivated for many years. This is North Texas, and it's flat, black clay soil. I would like to cultivate it to produce Bermuda hay, or at least make it a lawn/grazing area devoid of weeds or other obnoxious plants. There are no horses on it right...

Needed to mow tighter areas, not too mention the need to up my cool factor :cool:

I've got a pretty good leak in the gearbox on my MMM. The deck is 1.5 years old and has maybe 130 hours on it. Last week, I cleaned and serviced the deck, and topped up the gear oil in the gear box. It took a few ounces, which raised an eyebrow. Then I mowed about 4 acres and the dad-gummed...

Dear BXpanded, or some other accessory manufacturer: Please make a mid-PTO cover sleeve that is splined, slides on the shaft when the mower is off, and has a detent/button that works kind of like other PTO shaft latches. It should scrape the splines clean as it is mounted and removed. I am...

Are their any reputable internet order/dealers for the Kubota bits and pieces? Thanks...

You know, the little bird-beak on the air cleaner housing you pinch to let dust and grit out. Well, my BX2660 is about one year old and has 140 hours on it. The other day I am doing the pre-flight check and give it a pinch, and it crumbles in my fingers! Anybody else experience this?

I need to fertilize about 5ac of fairly open pasture. This is a once, maybe twice, a year task. Will use my BX2660. Would like some guidance on 3-point vs. pull behind, vs. receiver hitch electric (my BX has a sturdy 2" receiver on the draw-bar plate). If you could mention make & model that...

This is my simple rear light install. I basically bolted the SoundOff light to the slow-moving vehicle sign bracket, ran the wire through the fender with the turn signal cable, and then spliced it to the rear running light wires (the red light on the fender). Since this 500 lumen LED light...