Recent content by Mallard1

  1. M

    Kubota BX2200 starts then dies

    Thanks for all of the help, I put a new stop solenoid on it and it works great now. Thanks again for the help.
  2. M

    Kubota BX2200 starts then dies

    Thanks for all the help, Looked at the tractor today and it has three wires for the solenoid, Black, White, Red with black tracer. Testing the three showed it is getting the correct voltage, Black is ground. White 12v when cranking. Red 12v when key released. I ordered a solenoid today...
  3. M

    Kubota BX2200 starts then dies

    Thanks for the help everyone, I'll take a look at the coil and look at the wires on it. I saw there are 2 different solenoids, I'll have to get the SN to see which it is.
  4. M

    Kubota BX2200 starts then dies

    Helping my grandfather with his early 2000's Kubota BX2200 ready for cutting grass. The tractor will crank and run will holding the key in the start position, as soon as you release the key it dies. I have cleaned the battery connections and charged the battery fully. I don't think it is a...
  5. M

    NH T4.75 Hydraulic plug location

    I'm back on this project and I wondering if I place a T where the front end loader valve returns to the case could I put the fluid there? I believe that would be placing a T between #4 and #5 in the diagram below. Does anyone see any issue with placing a T here and using this as my return...
  6. M

    NH T4.75 Hydraulic plug location

    I looked at the tractor today I believe I see the current return circled in red. I also see two either bolts or plugs. Any idea if these hold something in place inside the housing or are just plugs? I really don’t want to pull them and drop something loose inside. This the the same
  7. M

    NH T4.75 Hydraulic plug location

    It has the 2 quick couplers per valve, these will work fine when using the lane however when stopping the lane shark the centrifugal force of the blade will keep them spinning which makes the motor act as a pump and there is nothing to relieve the pressure. With having it plumbed direct to the...
  8. M

    NH T4.75 Hydraulic plug location

    I don't think that will do what I need. I need to either tee into where the hydraulic fluid returns to the tank or find an extra plug that is not used that goes into the tank. I'll have the tractor at my house in the next week or two to take a closer look. on my JD4320 there was a port...
  9. M

    NH T4.75 Hydraulic plug location

    Trying to help a friend plumb his NH t4.75 for a lane shark. they require a hydraulic line that returns to the case of the tractor rather than through the typical hydraulic port. Does anyone know where this is located on these tractors? Thanks for the help.
  10. M

    New holland t4020 with 810tl curl leaks down while running

    swapped the curl and lift lines around coming out of the valve today and it still is leaking on the curl function so I assume it is one (or both) of the curl cylinders needs repacked.
  11. M

    New holland t4020 with 810tl curl leaks down while running

    what is the best way to isolate them? just unhook or do i need to cap the lines?
  12. M

    New holland t4020 with 810tl curl leaks down while running

    My FIL has a NH t4020 with a 810tl with 1000 hours on it. Just recently the curl started leaking down while running and when off. it will completely leak down in just a minute or two, enough you can watch it and see it move. there is no issue with the boom. If you curl it back it will pull...
  13. M

    no till drill's

    Thank you, when I’ve planted clover I also plant either wheat or oats on top, however I plant more clover seeds per acre than the cover crop. I see on the GP model it would still do this. How does that work with the genesis? Do you just adjust the ratio of seeds in the hopper to achieve the...
  14. M

    no till drill's

    with the multiple seed boxes on the great plains I assume you can plant 3 different types of seeds at the same time? is this correct? how does the genisis work with planting different sized seeds or seed blends?
  15. M

    no till drill's

    mall of our food plots are fields or lanes that are currently established food plots. we have used cultivators, discs and tillers in the past. We have removed all stumps, roots and they have been smoothed out. Then we broadcast and cultipack down. we are looking to improve the plots and...
 
Top