Recent content by Sportsman762

  1. S

    Material for hydraulic hard lines, Copper-Nickel or only steel?

    I would probably use Stainless lines and look for something with a 3,000 psi working. I would encourage you to go with 3/8" tubing as it will be close to 1/4" hoses in size. Tubing is measured by the OD and hose is measured by the ID. 1/4" tubing is extremely small and will be very very slow...
  2. S

    3010s New Holland tractor triple remotes

    Nice job. Very professional looking. Thank you for sharing.
  3. S

    How often should you grease a tractor for light duty?

    Good approach to good ownership. Its amazing what you find when greasing. Not a fun task, but an important one for good care of equipment.
  4. S

    How often should you grease a tractor for light duty?

    I try to grease every 8 hours. However I will grease before doing a large job, or after a long time of sitting. Figure the grease drives the water and contaminates out. I would love a battery powered grease gun, but have to settle for an air powered one for now. Greasing every oil change is...
  5. S

    Ford 917 Flail Need Main Rotor!

    The part number is BU81622. It is discontinued by CNH. it was previously $1621. Buying the parts unit would most likely be the best option, assuming no other damage was done to the unit when it snapped. Catastrophic damage like what is on your unit had to have required some significant...
  6. S

    What are the most reliable tractors to own?

    Reddogs, all the brands you list make good machines for the most part. They have all made duds as well. The dealer is the deciding factor. For example I know Challenger is a good brand, however my coworker has terrible issues with his, but most is due to an incompetent dealer. With that...
  7. S

    CountryLine Post Hole Digger PTO Shaft

    On a shear bolt style driveline the pin hole is normally small. Its a pilot hole and you drill it out to fit your needs.
  8. S

    Massey Ferguson 231 Injector Pump

    There is a member here who helps lots of folks on pump questions. He has an injection pump shop and is well thought of in this forum and others. Below is his profile. https://www.tractorbynet.com/forums/members/thepumpguysc.91346/
  9. S

    Door handle for Kubota MX54 factory cab.

    I am assuming you have a Kubota MX5400, since the MX54 is not a valid model. The door latch on the MX5400 left door appears to be the same as the Kubota B3030. The B3030 has a handle for the right door I am guessing that they would work on your right door. Below is the diagram for the B3030...
  10. S

    New hydraulic top link won't clear the lift arms on my B-series

    Not Sure about AU, but finding banjo fittings in the US is terrible. We normally replace them with O-Ring Boss (ORB) due to rarity.
  11. S

    Case DX-34

    I believe the part you need for the clutch housing is SBA320111930. It is used on the New Holland TC34DA, TC35DA, Boomer 2035, T2220, Case IH: DX34, DX35. Parts Manuals can be found here. mycnhistore.com Salvage tractors can be found here...
  12. S

    What trailer should I get for Kubota Tractor, and what should I pay?

    Not sure were Reddogs is but if he is up north the steel deck trailers rust something horrid. Salt gets in between the deck and the cross members and wrecks havoc. What is the weight capacity of the current trailer are you using Red? I am surprised that it is struggling with your Kubota if it...
  13. S

    Front end snowblower conversion

    I hope you don't mine I have a few more questions. What did you use for a pump and motor, make/model or specs? Also what were the diameters of the lines you used?
  14. S

    Front end snowblower conversion

    I do not know how I missed this thread. Orebonder you did a great job on the fab work. Thank you for showing us what you did and how you constructed it. I am curious on some details on the reservoir. The well pressure tanks generally have a diaphragm that is attached to the inside sides of...
  15. S

    PTO driven leaf blower

    The Little Wonder blower most likely has a 3600 rpm engine on it. With a 540 PTO you will have no blow, and it will most likely turn the wrong direction. You will most likely have to replace the motor, or look at some serious fab work to make it function how you want.
 
Top