Recent content by TC33DA

I just purchased a JD 790 with a GM2072R mower. it is a rear discharge and has chains. I am cutting my yard 3 1/2". The mower cuts great just leaves rows if cut grass. It does not spread it out. Looks terrible. Any suggestions to get a even discharge or is this typical for a rear discharge...

I needed to move some dirt and gravel the other day and noticed my hydraulics were noiser than normal. The outside temperature was in the 40's so it was cold. I let her warm up for 10 minutes and the engine temp was normal. When I raised the FEL the hydrualics were noisy almost a winning...

I raked hay all day Saturday and ran the A/C. I normally clean the cab filter with air after each dusty day. I noticed the evaporator coil had some fine dust on it. I was not sure how to remove it. I tried to vacumme it but did not have real good luck. Anyone else have this issue? The...

I realize I am the the smartest engineer our there, but why would JD put the rear windshield wiper on the right side? When you look at the inside rear view mirror all you see is wiper box. The mirror needs to be on the right side so you don't hit it getting in and out. But the wiper could go...

My 3720 has 35 hours on it. The owners manual says change the oil at 200. WOW The hour meter started flashing today which means some kind of service schedule. My dealer said it was time to change the oil and it would reset it self. Does this make sense? I planned on changing the oil at 40...

WOW!!! I was using my JD 3720 today and the dust was bad. I decided to clean the filter for the cab first. That was very easy and it was dirty. Then I decided to clean the engine air filter. I had to raise the FEL up above the engine and hold the hood up with one hand to remove the filter...

My 3720 cab came with the "small" R4 tires. The data I found on the "large" R4 tires comes up to an inch. Maybe I just don't understand the size numbers. I thought the smaller would keep the CG lower, but an inch is not much (carefull).

I found a LX5 cutter in very good condition. Owner wants $350. I was interested in the MX until I saw the price, Anyone have and experience with this cutter? I have a JD3720 tractor

I ordered the 6" extenders for my cabbed 3720. I would like to add the JD rear fenders but not sure how they fit and how they are attached. Anyone know? They look like they are about 2" black plactic, Might help with the wheels going out 6".

I have a JD 3720 with cab and FEL on order. My 16' trailer has a rating of 7000 pounds. The tractor will come in around 3570# and loader another 1,000#, and then the fluid in the tires 500-750#. I am getting close to 7000# when I add in the trailer weight. What is my safe load weight? I...

I am looking at buying a new 3720. The question is cab or no cab? I don't use it everyday just play and small farming. I am not sure I want the cab, but realize this is the chance to get it. Later is not an option if I want the JD cab with a/c. What are the pros and cons other than the...

I have been reading the posts about TC33 not starting. Well mine would not start the other day, Nothing. Pulled the service manual out and traced out the wiring. Looked at the fuses and found the 10 amp controling the alternator and safety was blown. Put another one in and it blew...

I have a 2004 TC33DA that is a good running tractor. How does the JD 3520 match up? I found a 2007 JD 3520 that is in very good condition. Both have a FEL. THanks

I have JD 1050 in good running condition. 4WD and a FEL. The unit has 3800 hours but mostly cleaning out the barn and garden work, nothing very heavy. I think somewhere in the $7K - $8K range. Any recomendations? The machine is always been sheltered. :o

I just converted fom Green to Blue. 2004 TC33DA. I want to install a 4 in 1 bucket. Did some research and realize a 3rd hydraulic function valve is required. Any suggestions? My local NH DEALER had no good recomendations. Thanks