Recent content by Trails2004

  1. T

    Question about a thing in Wyoming.

    It’s likely a telecommunications reflector of sorts.
  2. T

    XUV835M

    Below are screenshots from the 825 and 835 Operators Manual. I stand corrected, the literature does not specifically state that you must be stopped to engage 4wd. The only guidance provided is do not engage 4wd while stopped while the rear wheels are spinning. 825i 835m I apologize...
  3. T

    B Boss 6x6 plow setup

    What if you use this type of setup? Note pulley is mounted to the blade:
  4. T

    SuperATV Sale June 15th 2019

    SuperATV's 15th Anniversary - 15% off on the 15th Sales SuperATV's 15th Anniversary - 15% off on the 15th Sales - John Deere Gator Forums
  5. T

    Can the VIN / PIN be used to show the year of manufacture

    I think I have seen a link - but I cant find it anywhere Im looking a new to me JD tractor- Im unsure of the year of manufacture. Can you use the VIN or PIN to decode the year?? Thanks
  6. T

    FYI- Rimguard cost - Rocky Mtn West

    I just had my JD 3520 drive wheel tires (15x19.5 R4's) filled with Rimguard the cost was 3.35 per gallon. They added 29 gallons per tire ( 310 lbs ) The other local tire shop was pushing CaCl2. When I asked if this product was safe to use- they replied a tube is recommended--- So I guess it...
  7. T

    JD Ballast Box- Reinforcement

    I have searched and could not find any information- If this is a duplicate thread my apologies> Has anyone been concerned with filling their BB with cement - without reinforcing the 3 point pins in the box?? A coworker mentioned I should not use cement for fear of damaging the 3 point lower...
  8. T

    Carryall Build with Photos

    Last weekend I built a carryall. First I painted the frame then I stained the planks and assembled once dry- OK almost dry :o Other accessories will be added soon ;) Materials: 2 x 8 rough sawn planks Alot of carrigage bolts- I think 48 in all :cool: 4 flush mount "D" rings- 1200 lbs cap 4...
  9. T

    Trailer Hitch with Photos

    Last week I put together a trailer hitch for my JD 790. I used a hitch that I removed from my truck when I installed a new Tow Beast class V hitch Materials Used Truck Hitch from 2002 Dodge CTD 2 1/2 x 3/8 strap 2 ea Cat 1 to Cat 2 pins with bushings a chunk of 2 x 2 tube a piece of 1 1/4 pipe...
  10. T

    King Kutter Carry All and I Match Compatable?

    I have tried to search- without any luck I recently purchased a KK carry all and when I tried to hitch to the Imatch- the top link bracket is about 3.75 to high??? The top hook of the IMatch will not connect to the top link pin- the lower pins are OK Anyone else with this problem?? I have...
  11. T

    JD 790 Bucket Weldable Hooks

    JD 790 Weldable Bucket Hooks I recently installed 2 - 5/16 G70 hooks from AW Direct Weld-On Grab Hook - Grade 70 - 5/16" - Mfg# 11-516WGH welded in-line with the lift cylinders ( thanks for the advise ) and one "D" ring welded in the center of the bucket. I used a 2" x 3" 1/4 inch angle...
  12. T

    Roy Jackson

    Does Mr. Jackson still post on TBN??? I have enjoyed reading his posts, I was wondering if he still participated on this forum.
  13. T

    JD 790 Battery,Maintainer & Block Heater Install

    As a one of the new guys on the block, I wanted to share some recent modifactions to my "new to me" 2003 790. The first step was to add a block heater. I read many threads on the this forum before I tackled this project. I read the pro's and cons of the "katz" in line type heater and a "block...
  14. T

    Newbie here in Wyoming

    Hello I have been lurking and dreaming of owning a tractor for quite sometime. I was in heaven when my wife and I toured the JD plant near the quad cites a few years ago. I pulled the trigger and made an offer on a 2003 JD 790 w/ 320 hours 419 loader, 7 backhoe, Box blade, rotary cutter and a...
  15. T

    2003 JD 790 w/419 loader

    A newbie here with probably a question that has been asked a zillion times :) I just made an offer on a 2003 JD 790 with 320 hours, 419 loader, 7 BH, BB, PHD and a rotary cutter ( is that a RC?) they were asking 16,000 I offered 15,000 and asked if they could deliver to my home ( 6 hours away...
 
Top