Search results

On the 100 hours the piston broke, i reported it, it was still under warranty. Dealer replaced it. Now the boom has cracks!!!!! They beefed up the hydraulics but forgot to beef up the tractor This is when the piston broke actor

Another question: I have two chargers/maintainers. The first one after connecting pretends to disulfate, charge and after it charged the battery to 100% it keeps constantly fluctuating from 13.4V to 13.55V non stop. The second one does the same but after charging the battery to 100% at ~13.5V...

Last week i bought two NOCO Genius1 chargers/maintainers. I put them on two different batteries, one is 800CCA marine and another is a small 230CCA ZT. Both batteries were fully charged before i connected NOCOs. Both chargers were blinking red light for a few seconds then went solid green. It is...

I know it was discussed before but i could not find any info on hydraulic oil filters cross reference. Just came across this site. Feel free to delete if this was posted before https://www.filtersfortractors.com/branson-2515h-filter-cross-reference-info/

I have rather large wrap around deck on my house Every year i pressure washer it and seal it with Thompson's® WaterSeal. It lasts about 6-8 month and then by the next spring the deck looks like crap and i need to do it again. There are discussions about trailer decks treated with mix of motor...

Another stupid question, searched everywhere, cannot find and answer. I have a 27 Ton splitter and it leaks at two connections on the control valve. One is 1/2 ORB (3/4" thread OD) and another is 5/8 ORB (7/8 thread OD). I went to NAPA at least three times to buy correct O-rings. Whatever they...

In my area most farmers don't use them saying "i don't have anything to do close to the PTO while it spinning" or "if my ass is not in the sit, the PTO is not engaged". What says you, the ppl i trust? PS: The item in question is this

The first time since i bought it i tried to engage PTO. I turn the nob, the indicator light goes ON, i hear some noises from the transmission but the PRO is not spinning. Any thoughts?

Here what i get

Are there? Or if you have 5 ft, do you think it can handle 6 footer?

I want to buy a 6' rotary cutter. I found on the local Facebook market place two of those. The condition is similar when for SQ720 the owner asks $100 more. $1250 vs. $1350 When i could find specs for SQ172 nothing about SQ720. Is there any difference? I know the SQ172 has 10GA deck and cuts up...

Just noticed how negligently it was made. It is disrespect IMO 1. What is "Fuel-Oil element"??? 2. On 500 hour service they recommend replacing the oil. But the filter you supposed to replace at 550 hour mark, really??? 3. No services should be performed after 700 hours and no oils/filter...

I want to replace my roof. I noticed some roof contractors make valley with metal (sorry, i dont know the terms, i guess it is valley flashing but might be wrong) and some just overlap shingles. Does it make any difference and which one is the way to go in your opinion?

As the title says, when it is cold starts right up. works for 5-10 min then dies and would not start again. Let it cooll for 20 minutes, starts and dies almost immediately. Next day starts from the first or second pull. Put a new carb, same thing. Spark plug is dry and light brown color. Spark...

I had a swisher brush cutter sitting in my barn. It is a good thing, but it is hard to use in tight places or where the brush is very thick. So, made some improvements. I had a patch 20x50 yards of really thick bushes which i did not had courage to approach. Today i did it!!! This is after...

I have Branson 2515 with BH150 backhoe. It is a subframe model. The question is, when i attach the backhoe, should i extend the top link so it pushes on the backhoe or should i shorten it, so it pulls the BH towards the tractor. To keep it lose, the BH has too much play and jumps around, feels...

I guess it was discussed and there are many designs, but for some reason i could not find where to put it. Just wanted to share my design with was easy to make and works very well for over 8 month already and countless cords of wood.

Looking for an advise and TBN collective wisdom. I hired a concrete contractor to make me a patio with exposed aggregate concrete. The guy came, poured the concrete, sprayed the retarder, waited about 2 hours, washed and left. When he was leaving i asked them why there are so many spots covered...

Hi guys. I was posting on the hydraulic forum about my backhoe BH150 problem with my 2022 2515R On the swing it starts real fast, then slows down, then jumps again slamming the tractor, I recorder it on idle RPM because on the 2000 it is so violent. Here is the forum...

Need advise, Yesterday my backhoe started acting up. If i take the boom all the way to one side and then start turning it back, it goes 1/3 of the way, then stops for a second, then keeps going another 1/3, then hesitates again, then goes all the way to the end. Pretty much same thing with the...

I always, with no failure, forget to disengage my parking brake. It sooooo pisses me off, not because i forget to do so, but because it is one additional reminder of my age :mad: In addition to a visual indicator i thought a loud noise would be helpful. It seemed that installing a buzzer in...

Was browsing for some metal at my local metal recycle place. Found some good size angles. for $0.30 per pound it was not a brainer. Ordered some baler teeth online. The Carry all come out much stronger than the store bought but i actually have no use for it besides attaching the rake. I...

New 2515s have a cupholder attached to the left side of ROPs. Had some free time and added another one on the left side

Plastic pad of the "Gas"/RPM pedal was constantly falling off. A quick fix - drilled two holes and secured it with a cable tie.

Tried my welding skills (not so good, haven't been welding for more than 45 years). But eventually it worked, i'm happy with the result. Got it right on the second try. On the first one of the cross bars got bent. Removed them and it seemed to work better.

On Branson tractors there are two pins used to secure the boom. I always was concerned to loose them. Came up with this little hanger. I bet there are better ways of doing it, but it was quick and easy.

My new Branson/TYM came with a really questionable storage box already installed. The bad: It is extremely flimsy and small, useless IMO. The good: It has a really sturdy bracket able to hold a huge load. Removed a pile of original garbage from the tractor (it is my opinion they are garbage...

Upper part are welded together chain links, the bottom part is 1/8" metal.

I dont like driving on 4WD when it is not necessary since my property has asphalt roads and i feel it increases front tire wear unnecessary. It was easier then expected.

Out of PVC pipe and EBay charger

I like to be able to get on/off the tractor from both sides, however there are some obstacles on 2515. 1. The FEL stich is on the way, let alone it is inconvenient for me to hold my right hand in this position dictated by the stick position, maybe it is just me. 2. There is no step, and jumping...

Hi All! New here. My 2515R just had first 100 hours on it. The question is, for the rear tires the manual says the rear tire pressure should be 2 bar which is roughly 29PSI. On the tire is written 23PSI. the dealer says 30PSI. The tire manufacturer, i called the US rep, says 23PSI. Which one...