Search results

In my parts manual it lists D1803-cr-E4-LB2 also an D1803-cr-E4 LB-4 can you please tell me what LB2 and LB4 means so I know what I got Eng.#D1803-71CY8121 I think its the tier number but not sure I have an 2020 L-3901 Thanks

I have been trying to find the requirments for hauling equipment etc. on a 7k tandem axle utility trailer, such as what to use for a tie down... chain or straps and how many etc. tried thru state with no luck Thanks

I have a rck30b deck From a b2630 that I am trying to sell does anyone know if it will fit a b2650?? I think the 2650 calls for rck30b-a.. whats the difference if any thanks

What am I missing here not my first tractor ?? Just got a new 3901 and had the slider bars put on 3 point, the bars are on outside of the arms so when I spread them they hit the R4 tires.. They do not spread wide enough for my box blade and some other attachment pins...this makes for alot of...

Trying to decide on new tractor got it down to two I think kubota grand 3560 or mahindra 1635hst no cabs/with a loader only on either tractor,,always had kubotas but I am not sure on the DPF on the kubotas anyone with pros and cons of each thanks

Looking to buy bigger tractor any pros and cons on the mahindra 1635 hst with rop,, I have only owned Kubotas thinking about a change

I could not find the other thread on this and not sure I posted in correct place but I have a creek bridge with 16 ft span made from 2 treated 6x6 glued and bolted together Beams spaced same as tractor tires Right now I run my b2630 across it wondering if it would hold a 6000 lb tractor

Does anyone see the need to load their rear tires for loader work? Looks like pretty heavy tractor already

What is the correct HP on the B3350 some say 30 like the Kubota web site,, others are saying 33 Also have the new ones changed over to rail injection thanks

Does anyone know if Mark is still making stabilizer bars if so how can I get a hold of him? I tried an email I found but it won't go thru.....thanks

My B2630 seemed to be very low on power when starting. Figured had a bad battery, I had it tested and was told it was okay just low on charge. I tested my dynamo and had 14vac at idle and 40 vac at full rpm so I changed my regulator.. At the battery when idling I get about 12.5 volts and at full...

Looking for ideas, the left front wheel bearing (outer) on my b2630 has broken three times on now. The outer race on the bearing shatters, balls run to top, shaft drops and eats the seal, big oil mess too. This time it cracked the outer gear case cover..Never happens on right wheel. Not hard to...

Anyone ever have a opc module go bad? I have a B2630 that intermitingly blows the 5 amp fuse on the safety circuit. I went through all the wiring and switches, nothing looks bad switches all read good. When it blows I was just pushing hydro pedal to reverse (no pto on)..Any ideas, Thanks

I installed an electric start Briggs 122037-0550 engine on our Agrifab lawn vac, but there is a grey wire with white connector coming out of the engine does anyone know if this is an AC lighting wire or a DC battery charging wire I hooked up my fluke meter to it and it reads on the ac or dc...

Last year I bought the wife a new t2380, I didn't pay to much attention to the deck. It's a hanging deck not a floating deck..It gives a very poor cut in my yard, very uneven and gouges. Other than that it seems like a nice machine..Now she wants her Simplicity back. Anyone else have this...

Been thinking of getting a add on grapple for the loader on my B2630 Kubota. I can't figure out if I need the double thumb or the single. Any expierience on both would be app. Thanks

When I start my tractor up (cold) I have no hydraulics I let it warm up about 5 min, then have some (little) use...If I try and drive it the pump screams and I don't have any steereing, forward or reverse, loader movement etc... After it gets good and warm everything seems fine..I haven't had...

This is probably in here somewhere But I can't find it. After changing oil and filters on hydro my transmission is real jerky and loader moves real slow. Do I have air in the system and if so, how do I bleed it out? I have a B2630 Thanks

I am going to buy a box blade and some have a hinged back blade and some have a two sided blade for forward and reverse pushing anyone have any pros and cons on either one???

I know this has been gone over a bunch but I'm still not sure of the answer... I was going to buy one of those 50 gal. plastic tanks from the farm supply store ( the white ones ) to store some diesel fuel in. Will the fuel eat the tank or cause the plastic to swell? some say yes some no.Some say...

My son found two large snapping turtles dead in the shallow water of our pond today.. Any ideas what causes them to die like this?? To me it's no great loss I was just curious if anybody would have a reason:confused:

I was looking into the Dr grader for working on my lane. My question is would a box blade do the same thing? And I could also use for other things...Has anyone bought or used the Dr grader? How do you rate them? thanks

I'm considering switching from dial up to the Wild Blue satelite internet. Do any of you use this? If so,any good or bad feed back would be greatly apprecciated.. OOPS did a search and got alot of good info, is there anyone in central Illinois on this ? THANKS

My son broke the left lens on my headlights and the dealer said you have to buy the whole assembly and it cost $154 Does anyone know where I can get just a lens? Thanks

My son broke the left headlight lens on my tractor, and when he called the dealer for a replacement lens they told him he had to buy the whole assembly. It costs $154 does anyone know where you can get just a lens? Thanks

I was wondering if any one has been able to cross reference the engine oil filter (70000-74034) to another brand other than Kubota. I crossed the the rest of the filters with Wix #'s but this one won't cross.... Thanks

I know this is a tractor forum but I have a generator question and you folks seem pretty smart about things. I am going to buy a portable generator for my house and I would like to get propane(have a bulk tank for the house) or tri fuel model. I noticed some models have idle control (alot more...

Does anyone have a fix for the seat on the 2630, it feels like your sliding off the front. It needs to be tilted back some how. Is this a problem for anyone else? Or don't I have enough a_ _ to keep it down? thanks

I have a new b 2630 with 58 hrs on it and I noticed the rear end getting hot.Also the rear pto chatters pretty bad. You can't leave your hand on the rear end it gets so hot. I noticed this before and after the 50 hr service. I called the dealer and he said they had no service bullitens on it and...