Search results

Results 1 to 12 of 12
  1. P

    Long 445

    I have an UTB 445DT which is the 4WD version of the Long 445. This is a selectable 4 WD or front wheel assist arrangement. On mine the front axle can move forward or backward by over 1/8"! I could, for now, slide in a brass thrust washer to take up this slack, but its clear the trunnion bearings...
  2. P

    Backhoe /TPH hydraulic conundrum (long)

    I have a Long 445DT which comes fitted with a factory remote hydraulic valve intended to operate a double acting cylinder via two quick connects at the rear. Down feeds one connect & up feeds the other. It has previously been modified so that the lever-down valve outlet is piped to a spool...
  3. P

    PTO speeds

    My PTO has two options (plus neutral). One is 540 & the use is obvious, but the other is "Ground Speed" - what would that be used for?
  4. P

    Lift arms rising by themselves

    I'm using a tractor with a TPH mounted implement basically for the first time ( an Universal 445DT sold as a Long445 or Allis 5045 in USA ) & running a 5 ft Rhino topper similar to a Bush Hog with a rear castor wheel. I've selected position control & set the TPH arms for a suitable height to...
  5. P

    Toplink Toplink pin

    I'm having trouble fitting a toplink pin (3/4") to a Universal 445 (Long 445 or Allis Chalmers 5040 in US). I've turned some pins to 3/4" on the lathe - they fit the toplink well, but I cant get them into the toplink housing on the tractor - there's no way to get a straight push on the pin to...
  6. P

    Allis 5040 /Long 445 toplink

    Just thought I'd turn up some 3/4" pins on the lathe to fit a top link to my Long 445 ready to run a bush hog & mower I'm picking up Wednesday night. Pins are great & fit the top link easy, but cannot get them into the toplink support on the tractor. There are 4 holes for the toplink pin, but I...
  7. P

    Allis 5040 /Long 445 toplink

    Just thought I'd turn up some 3/4" pins on the lathe to fit a top link to my Long 445 ready to run a bush hog & mower I'm picking up Wednesday night. Pins are great & fit the top link easy, but cannot get them into the toplink support on the tractor. There are 4 holes for the toplink pin, but I...
  8. P

    Backhoe Backhoe - Fronthoe??

    I have a backhoe with a subframe mount that doesn't suit the tractor I've bought - Long (Universal) 445 DT. I was going to mount it on the TPH, but my tractor has a good quick release FEloader on it (See picture attached) & the brackets & rails for this are really meaty, like 3"X3/8" angle plus...
  9. P

    Long 445

    Should the TPH arms power down as well as up on the Long 445? Mine lift fine, but won't come down without some weight on them. This is my first real tractor so I don't know if this is normal. If it ain't, where should I look to clean/adjust/repair?
  10. P

    Backhoe Backhoe hydraulic connection

    I just bought a UTB ( Long) 445 DT (4 WD) which has a FEL with spool controls in the cab, plus a single rear hydraulic Q/D outlet. I want to run a backhoer on this, which has two hydraulic pipes marked in & out. Assuming the "in" pipe is connected to the rear outlet, where should I connect the...
  11. P

    Backhoe Long 445 & backhoe

    I just bought a UTB ( Long) 445 DT (4 WD) which has a FEL with spool controls in the cab, plus a single rear hydraulic Q/D outlet. I want to run a back actor on this which has two hydraulic pipes marked in & out. Assuming the "in" pipe is connected to the rear outlet, where should I connect the...
  12. P

    Back Actor hydraulic connection

    I just bought a UTB ( Long) 445 DT (4 WD) which has a FEL with spool controls in the cab, plus a single rear hydraulic Q/D outlet. I want to run a back actor on this which has two hydraulic pipes marked in & out. Assuming the "in" pipe is connected to the rear outlet, where should I connect the...
 
Top