Search results

Results 1 to 50 of 103
  1. daman1

    Mahindra Tractors-Should You Buy One?

    I wouldn't touch one with a 10-ft pole for the above reasons and others, just a cheaply built tractor
  2. daman1

    Oil & Fuel GC1715 Blowing hydraulic fluid

    Is that a factory backhoe tractor or non-backhoe?
  3. daman1

    Kubota BX2200 loader will not go up or down

    Switch ur hoses from bucket to boom, does it work?
  4. daman1

    PTO - live and learn

    Or........ just make sure you double check and it's always snapped in properly, always tug on it good and make sure it's snapped in and won't pull off
  5. daman1

    1725 takes a while to start

    Per owner's manual
  6. daman1

    1725 takes a while to start

    The 50hr service is ONLY.... engine oil and oil filter, plus check for loose hardware, no sweat
  7. daman1

    1725 takes a while to start

    You need to post a video so we can see exactly how long it's cranking, a puff of black smoke at startup is normal
  8. daman1

    Suggestions for light weight pallet forks

    They make pallet Forks UNDER 200 lb with 36" forks that's what you want for a subcompact
  9. daman1

    Massey Ferguson GC1725M Backhoe CB65 Broken Joystick - Answers

    Thanks for posting this info
  10. daman1

    HOW TO: Adjust the Pressure Relief Valve (PRV) on the MF GC 1705/10/15/20

    Your going to have that issue with any brand and dealer. Just wait till warranty is up then your ok
  11. daman1

    HOW TO: Adjust the Pressure Relief Valve (PRV) on the MF GC 1705/10/15/20

    They will say "it's where it supposed to be" and that it's been tamperd with, trust me
  12. daman1

    HOW TO: Adjust the Pressure Relief Valve (PRV) on the MF GC 1705/10/15/20

    Thats odd because MF has some of the highest settings for hydraulics I've seen,,my new 1723 tested 2000psi on the dot, spec Is around 1900 I believe. You do know you violated your warranty any problems they can/will deny you.
  13. daman1

    Kioti Broken in Half

    A combination of a junk tractor and design and abuse, I've seen a couple posts on the web now of a kioti cracking and breaking in that area. POS. And then try to get any warranty work out of them good luck
  14. daman1

    Cheap FEL cylinders keep bending

    I don't care what bucket is on it somthing is wrong!!, them cyls should not be bending, there is a fault in the rods, undersized or not hardend properly, they look undersized to me, the older cb65 sub compacts bh had the same issue with the dipper cyl, new revised cyls were issued and problem...
  15. daman1

    ZTR Maintenance

    Carburetor problem you need to get it cleaned
  16. daman1

    Fram tractor hydraulic fluid?

    I no all that, I do them all the time, it'll give you the additives that matter, anti wear anti corrosion etc..
  17. daman1

    Fram tractor hydraulic fluid?

    By a VOA, additives and base oil separate the men from the boys. Not all additives and base oils are created equal
  18. daman1

    Looks like a great log splitter

    Yup its a log splitter
  19. daman1

    Made her shine

    Of course, I waxed my new GC about 3 times already! :cool:
  20. daman1

    Backhoe hoses won’t reconnect

    You still have pressure someplace, either the male or female end.
  21. daman1

    Turf tires vs r4’s

    Lower your air pressure, on my gc I have them around 14-15 psi.
  22. daman1

    Bent bucket cyl on model 48 backhoe

    I've seen that before on sub-compacts I bet you there's a manufacturer defect in the iron in that rod it was forged too soft. Happen to have any warranty left on it?
  23. daman1

    Quickconnect hydraulic coupler issue (and not from too much pressure)

    Use said the male connector did you try the female connector? Does that easily push in? If you have pressure on one side they won't go
  24. daman1

    Recommended oil filter for 18hp Kohler Courage Engine (just purchased new).

    Pure coincidence. In six years there could have been any abnormal crankcase pressure any type of dirt and debris, mechanical failure in that seal to make it leak 3 weeks ago I picked up a 470hr big Cub Cadet with a Kohler 27 horse engine guess what went in yep Mobil 1 full synthetic no issues...
  25. daman1

    Which Backpack Blower?

    You said all Two Strokes I believe
  26. daman1

    Which Backpack Blower?

    Get a 2 smoke snowmobile out on the lake hold her wide open throttle for few miles see what happens
  27. daman1

    Recommended oil filter for 18hp Kohler Courage Engine (just purchased new).

    That is nothing but pure coincidence i use synthetic oil in high-mileage vehicles and high hours equipment for 25 years and also at work not once was there ever a problem. Most modern day multi viscosity synthetics of good quality have very low VII and shear very litte they're pretty much...
  28. daman1

    Hydro fan

    How about investigating the pulleys and see why it's falling off, these pulleys have guides on them that keep the belt on track and running true if your belt is falling off or breaking you have a problem somewhere
  29. daman1

    Which Backpack Blower?

    "Long hours at a time", I'm sure she's getting hot and at the recommended 50:1? I can see why ur having bearing issues. Go to 40:1 and shorten the run time
  30. daman1

    Trading in an almost new tractor?

    See what a dealer will give you Dealers Supply is pretty scarce nowadays lots are empty you may be surprised what they would give you for a trade in. If not sell it outright good used clean tractors are very sought-after nowadays
  31. daman1

    G730 fill /vent plug?

    Thanks but no it's not I could not blow either way in or out that little paper disk had it completely blocked off, usually these type situations there's only pressure and if that's blocked off you could blow out axle seals. That's why I'm wondering if anybody else has seen this while servicing...
  32. daman1

    G730 fill /vent plug?

    did a service on the transaxle today and while I had the vent plug off I found that I couldn't blow through it upon inspection it looks like there's a paper washer in there preventing it from venting has anybody seen this before why would they have of then but then plug it off with this paper disk?
  33. daman1

    I thought Sthil made a good saw?

    Did Stihl make that bolt, forged in their foundry? No they get it from a supplier that probably had a bad run with wrong tempering, shit happens, stihl has a very quality saw.
  34. daman1

    MF 1526: Maintenance Information Inconsistent

    Though not as bad is your tractor info my brand new gc1723 is kind of the same way, I kind of go with the owner's manual and then do a Google search see what everybody else is doing lol
  35. daman1

    Selling your Machine?

    Facebook Marketplace is probably going to be your best bet. A lot of people that are buying look there
  36. daman1

    Kioti DK 35 FEL leaking down periodically

    Even brand new equipment will leak down if Hydraulics are left in the air which is totally normal
  37. daman1

    BX owners: any ways to increase loader capacity?

    MF specs there GC series at just under 2000psi stock, mine was spot on 2000 when I got it home, rasing a bx up is fine IMO.
  38. daman1

    BX owners: any ways to increase loader capacity?

    Check YouTube out plenty of videos on how to do it
  39. daman1

    Backhoe Broken Joystick after 10 Hours (GC1725M/CB65)

    Nice, sometimes that's all that happens
  40. daman1

    GC1705 DL95 loader question

    If everything still original I believe 2016 switch to 3/8 connectors and the dl95 has 3/8 connectors also so you should be all set
  41. daman1

    Backhoe Broken Joystick after 10 Hours (GC1725M/CB65)

    The new BH2720 has addressed this issue
  42. daman1

    Oil Dilution

    Idling is the major cause of fuel dilution run cheaper oil and change it every 3000 or get rid of the car get something else
  43. daman1

    D1850FD oil stick>?

    Yea bummer
  44. daman1

    D1850FD oil stick>?

    Can you back trace your steps from when you changed the oil find it on the ground someplace or did it fall in the frame of the tractor?
  45. daman1

    warm up

    Exactly they don't own it they're in a hurry and they don't give a shit they're there for a paycheck
  46. daman1

    What do you do with stump once removed?

    Next time grind it out
  47. daman1

    Bucket level indicator rod---useful?

    After 17 years I would suspect your experience would come in the play and you wouldn't need that rod on there anymore
  48. daman1

    Backhoe Broken Joystick after 10 Hours (GC1725M/CB65)

    K thanks for the pn and info!
 
Top