Search results

Results 1 to 50 of 70
  1. kormidoit

    What did you do on or to your LS Tractor today?

    Did you do the plumbing for the grapple yourself ?
  2. kormidoit

    What did you do on or to your LS Tractor today?

    Just got started cleaning my lots after our big fire (Dixie Fire)up here in nor-cal....usually clean lots 6 times a year. 5 to 6 dump loads of branches and pine / fir needles. No burning here. Green waist for us. After a million acres burnt.....little gun shy.
  3. kormidoit

    MT225S cold start question

    What rear most blower did u get....Model and pic please.
  4. kormidoit

    Bucket Cutting edge added

    2. my neighbors Case bucket and a JD....both older....but no additional edge on theirs.
  5. kormidoit

    Bucket Cutting edge added

    Almost a year on mine....a little bur on the blade but ground that off. Still Doing the Job...Still sharp. Not allot of dirt work....some DG on the driveways...not mine, TONS of snow removal and still removing snow and thick ICE from street and our concrete driveways. Did 70 plus buckets of...
  6. kormidoit

    Bucket Cutting edge added

    This is the same one I had the dealer install when purchased new....I wanted the blade for bucket stability and not to wear down the bucket edge. 54" bucket on the MT225S. Blade is two sided.
  7. kormidoit

    Tractor quit and won't start

    Terrific....Now, why did it blow ??
  8. kormidoit

    XJ2025H Wheel spacers

    I purchased Bora 2" rear wheel spacers for my MT225S. So far so good....www.motorsport-tech.com
  9. kormidoit

    LS Tractor USA Parts Website

    Am I missing something???? I can look at parts....BUT can't order parts from the website. Issues?
  10. kormidoit

    Cutting edge for LS MT2 25S FEL

    This link does not have our loader on it either...LL2300.
  11. kormidoit

    Cutting edge for LS MT2 25S FEL

    LS Dealer....Lane Tractors....Los Molinos, CA.
  12. kormidoit

    Cutting edge for LS MT2 25S FEL

    YES....I ordered a cutting blade for my MT225S. Needed it to reenforce the bucket blade....I heard the bucket will bend. The blade is two sided, so when one blade gets dull, just rotate and a new sharp blade is ready....Yes it sharp and strong.
  13. kormidoit

    MT225S cold start question

    So this morning it was 9 or 11 degrees...depends on whose phone ur looking at....I have been cycling the glow plugs by turning the key to the Left 3 times....then to the Right, waiting for the GP light to go off each time....and she fires right up. So for the 225S drivers out there....try that...
  14. kormidoit

    MT225S cold start question

    My MT225S does the EXACT same thing....Absolutely gutless on cold starts. Does not matter what the key position is in. GP light is on for a second...thats it.
  15. kormidoit

    What did you do on or to your LS Tractor today?

    Removed the backhoe and covered it for the impending 5ft. of snow expected this weekend.
  16. kormidoit

    MT225S rear ballast ??

    Bobrown....I agree on the 'float" function if I was plowing....however I have to move snow with the bucket loader. FYI the little lever LOCKS the FEL stick from moving....be careful. If you want to get 'ice' off ur driveway....nothing better than the cutting blade on the from bucket....again...
  17. kormidoit

    MT225S rear ballast ??

    Driveway is concrete...goes from flat / slight to 6 degrees. Second house is assault driveway with shorter but 6+ degrees to road ( 500 yards between houses ). YES..... I have chains....thats why I purchased them and the 2" Rear Spacers to clear frame with backhoe attached. I have run chains on...
  18. kormidoit

    What did you do on or to your LS Tractor today?

    Excellent....Thank you. here at the lake we get some really heavy snow and big berms. I have a really long concert driveway...just worried about wear n tear.
  19. kormidoit

    MT225S rear ballast ??

    Excellent....I have the hydro lines fitted properly then. Again...Thank you.
  20. kormidoit

    MT225S rear ballast ??

    So another question is its ok.... 3 point attachment is on now.....isnt the down lever suppose to apply pressure going down or just gravity fed ? I have lift pressure but not downward pressure.
  21. kormidoit

    MT225S rear ballast ??

    Got it.....I have no implements at this time but will give it a try. Thank you.
  22. kormidoit

    MT225S rear ballast ??

    So we are coming into snow season and I will be loading snow and moving it to an empty lot across the street....I have taken off my backhoe for the winter, my MT225s has loaded tires from dealer, so do I need to add real ballast ?
  23. kormidoit

    MT225s Loader Valve Leak

    My dealer got the entire valve in las week....he three dated it....now just waiting for the dealer to come and pick up the tractor.
  24. kormidoit

    MT225s Loader Valve Leak

    WOW.....My 2021 MT225S blew 2 o-rings at the TOP of the same valve ( dealer said the nuts were not lock-tighter down)....$500 bucks to send it to the dealer who "fixed" it. However...just last week it blew AGAIN. Now the dealer is going to replace the entire valve. I seem to think it has to do...
  25. kormidoit

    LS backhoe factory thumb

    Paid $250 for mine from dealer in CA. I like it...use it allot...no issues so far with the thumb.
  26. kormidoit

    What did you do on or to your LS Tractor today?

    Installed 2" Bora Wheel Spacers. Needed clearance for snow chains.
  27. kormidoit

    LS Grapple

    Can we get pics of the 3rd function valves and the lever please....I am thinking of have my dealer add a 3rd function kit. Also what is the weight of the grapple ?
  28. kormidoit

    What did you do on or to your LS Tractor today?

    Blew the valve in the FEL....grabbed a bucket of base....fanned it out gong in reverse....rolled forward after empty...put a 45 degree angle on the blade...put the loader into float and floated in reverse....looked up and my dash was covered with fluid....the controller valve where the stick...
  29. kormidoit

    Grading LS MT225S W/4 FT Box Blade

    Going to order this week....REALLY appreciate your input guys.
  30. kormidoit

    LS MT225 Synchro vs HST

    I have many years driving gear vehicles...10 years driving tractors with HST. My environment (tight turns, hilly, tons of trees ) I live in and do tractor work...HST is a great option.
  31. kormidoit

    Grading LS MT225S W/4 FT Box Blade

    So....now ?? Steel or Aluminum spacers?? Opinions? I'm getting the 2" Steel or Aluminum just enough to clear the chains.
  32. kormidoit

    Grading LS MT225S W/4 FT Box Blade

    Thanks again for the link.
  33. kormidoit

    Grading LS MT225S W/4 FT Box Blade

    Thank you for the tip.
  34. kormidoit

    Grading LS MT225S W/4 FT Box Blade

    My dealer has not answered me on part number for wheel spacers....I asked a while back because of chains rubbing.
  35. kormidoit

    Grading LS MT225S W/4 FT Box Blade

    My tires are loaded also.....still tippy. I am Extremely happy with my choice...MT225S. It's perfect for what I need in a tractor.
  36. kormidoit

    Grading LS MT225S W/4 FT Box Blade

    When you move the seat up....make sure you push the pin back in to LOCK the seat in the higher position ...or it will flop down when you sit back down on it....unless u prefer to low ride.
  37. kormidoit

    What did you do on or to your LS Tractor today?

    Thanks for the link....looked at it....the trade off is an additional 160 lbs & $400 bucks for the longer tines. Hummmmm, decisions. REALLY appreciate the info.
  38. kormidoit

    Grading LS MT225S W/4 FT Box Blade

    I have the same feelings on mine....however I found it to be a small issue over the ret of the great performance I am getting. Only other issue is the tipsiness of the tractor. But I live in the mountains...so nowhere is flat...just have to be careful.
  39. kormidoit

    What did you do on or to your LS Tractor today?

    So looked at the EA wicked 55....wow...not low cost for sure. I need to take the tractor back to dealer and have them install the third function...then I'll take another look at it. I wish the bottom tines were a little longer. Reviews seem to be good.
  40. kormidoit

    Backhoe NEW MT225S owner....mechanical thumb issue

    Holy crap. I move the main pin to the center of the thumb to get that triangle config for strength....seems to work.
  41. kormidoit

    What did you do on or to your LS Tractor today?

    This is what I have....
  42. kormidoit

    What did you do on or to your LS Tractor today?

    I think the MT225S comes with SSQA ?? Im am too new to tractors to distinguish.
  43. kormidoit

    What did you do on or to your LS Tractor today?

    Want to know make and model of ur Grapple please....Should fit on my MT225S ??
  44. kormidoit

    XJ2025H not enough lift strength

    "Also about how when I set the bucket or loader arms down on level surface, the right one hits first by about an inch or so." SO.....I have a New MT225S and just got done with the 50hr.service....Last month I called the dealer and advise him of the EXACT same issue as what u described. He...
  45. kormidoit

    What did you do on or to your LS Tractor today?

    Added new feet today....we'll see how they do.
  46. kormidoit

    Backhoe NEW MT225S owner....mechanical thumb issue

    I really LIKE it....works Great...it's just mechanical...three length setting and a setting to stow when traveling.
 
Top