Search results

Need to drain and refill the gearbox on my Ford 917 flail. M1C137-A is what is called out- what is the closest equivalent?

I used Dayton J20 on my floor back when the shop was built. Acrylic system, easy to apply and reapply ( if necessary). Durable for most liquids ( got to clean up hydraulic fluid as it will deteriorate the acrylic).

Where I’m at in E. WA build costs for a ‘custom’ build range from around $250/sf to well over $300/sf. My last rough build cost estimate ( a month ago) came in right around $290/sf

I have exactly the same size building- I went with a 12x16 single door on the gable end of the building. I did provision for another door adjacent to it should I decide to install another garage type door.

In my case I had to grant an easement, pay for the transformer, base and primary ( as well as the meter base, etc) but not the co-op labor to run primary, set the transformer and hook up the meter. I did the trenching and backfill. Once installed the co-op is responsible for everything up to the...

I replaced mine (XR4155HC) using the same speakers described above- well worth it as the LS speakers are unbelievably bad. Not a horrible job but the OEM speaker/grill mounting arrangement leaves a bit to be desired from an accessibility and re-installation perspective.

Luckily we all get along in our 6 20+ acre/parcel ‘ development’. Our properties have a set of covenants that laid out the option of a road maintenance association and/or an HOA. We opted for the RMA ( with Quarterly Dues for plowing, gravel, sand, weed treatment, etc). When the ‘developers’...

Pulling 1 1/2” HDPE water line from shop to well a couple of years back

Mine does not leak water in operation ( at least I’ve never seen any on the floor)- you can see the install in the photo I attached

CSV is not a foot valve-completely different animal

I installed mine in my shop some 150’ from the well.

I shopped the heck out of chippers 2 years back and ended up with the Victory 8H mostly due to lead time ( got mine delivered less than 3 weeks after order), free shipping and price. It is, for all intents and purposes, a Woodmax or Woodland Mills 8H clone. My only really dislike is the lack of...

I run 1 1/4” hdpe from the pitless to the pressure tank/CycleStop valve (reduces to 1” at the tank/valve). 3/4” PEX to a Viega Manabloc. 1/2” PEX runs to fixtures. Well flows about 11gpm. 2 hp pump with about 50’ of head to the shop. No flow or pressure issues. I’m not a fan of PVC for water...

Thanks, I was aware of that as a solution. I still would prefer the option of a ‘switchable generator’ neutral as it eliminates altering the ‘as delivered’ generator wiring and would not occupy one of my 110v generator outlets. I have a ‘bonding’ plug that I bought after the main power panel...

What I really wish I’d somebody selling a generator with a switchable ( from bonded to floating ) neutral. I have the breaker interlock type install with a inlet plug so that I can hookup my cheapie Predator 8500w generator ( which is a bonded neutral generator)-I really don’t want to pull the...

Avenger, Interesting that we live in the same state ( and I think, in the same county) and got different answers (interesting but not surprising). I reached at to The Washington State Patrol Commercial Enforcement division with the same question and was told that it didn’t matter if it was not...

Eddie, Have you checked into the CDL agricultural exemption applicable in your state? I have a Ford LN7000 dump truck at a GVR of 28,500# normally requiring a CDL however with a WA. State AG exemption I can operate without a CDL within a 25 mile radius of my farm ( 25 is the WA limit- the Fed...

I’d certainly like to know more about the ‘auto heat’ algorithm as well as what are the limits to the function. My internet connection went down a couple of weeks back when we had a couple of feet of snow and a week of below freezing temperatures. Haven’t been able to get over to check antenna...

I’ve Bobcat 3400D- basically the same as the Polaris Diesel but badged for Bobcat. It is a bit noisier than a gas model and certainly is speed limited. I bought a diesel for one simply reason- most of my equipment is diesel and it cuts down on fuel storage. My biggest gripe with the 3400D was...

So, I bought one on a lark- it works, barely and is certainly not an improvement over either a file with a guide or my Dremel chainsaw sharpening attachment. Minor correction- the “ratcheting” feature is an improvement over either of my other sharpening tools.

Finally got a chance to hook it up. Connected fine- don’t have any codes so nothing to read or clear. Will try to get some live data tomorrow to confirm it is reading engine data.

I view my Swann cameras remotely via my Starlink. The cameras and associated DVR are hardwired to my Starlink router via an Ethernet switch and the Starlink Ethernet dongle. Have no problems viewing live video ( or playing recorded video) or making system setting modifications remotely.

I did my cruising boat that way for years ( had to of course). Never liked the vacuum oil sucker-waaay to slow ( even with pre-warmed oil). The small size of the suction tube that will fit down a dipstick greatly limits the flow. Even a powered oil extractor is going to suffer from the size of...

My shop was done in 3/4 EMT and 12/2 for most circuits (less W/D, water heater, mini split, welder and RV). I’ve added some additional circuits using the combination of 3/4 EMT and flexible armored wire- wish my bends looked anywhere near as good as the pro who did my original installs.

I was really interested in them after we saw a house nearby that had one ( apparently installed before all the west side regulations were either written ( or enforced)). Still think they are a terrific idea ( particularly when you’ve 30 acres of potential fuel available!)

Avenger, They seem like a great idea however there aren’t any that are currently ‘legal’ in our state. Have to be EPA certified and then be on the WA approved list-weren’t any last time I checked.

I’ve always used the T6 in my LS and in my Yanmar powered SxS. Still do my oil changed yearly just because oil/filters are cheap (relatively) and engines are not. Really not experiencing the life benefit of synthetic but get all the others.

Just an additional manufacturer to consider-Victory. I shopped the usual suspects and was pretty much set on the 8H before stumbling on Victory- their 8” hydraulic indeed model is a virtual clone of the 8H at a lower price point (and free shipping as well). Final decider for me was lead time...

I still haven’t had an opportunity to hook it to my XR4155-I’ll try to remember next time I’m at the ranch.

Not hard at all- I moved mine 3 or 4 times before I finally mounted it to the roof of my shop, I also was using it ‘temporarily’ on the ground while I waited for the roof mount from Starlink. I would stow the dish and bring it in to the shop when we’d head back home at the end of the weekend...

I debated epoxy vs acrylic when my shop floor was poured. After much consideration ( and discussion with the flatwork contractor)I decided to use Dayton J 25 sealant. If would be considered ‘less durable’ than a properly applied (key word here is ‘properly’) quality epoxy. In my opinion ‘less...

Got the chipper hooked up and started on reducing my limb pile ( again )-one of these days I’m going to figure out that mid-August is not the best time of year for limb chipping-gets darn hot picking and feeding the chipper! Piled the chips up near the developing orchard- going to compost...

We’ve had our dishy up for about 3 months now- moved from temporary ground mount ( which had a very minor amount of obstruction) to shop roof mount ( with no obstruction). I’ve been watching our speeds somewhat closely- we seem to range from 40-140 mb/s depending on time of day. Without a...

Or as it has been morphed “ the truth has been established, beat the facts in to submission “

Yes they do

And here it is:

My mini split outside unit specified the breaker size necessary on a data plate on the unit

I bought a wall mount with retractable hose from Giraffe tools last year. Mounted it outside shop main door at the H/C bin I plumbed a couple years back- really convenient for washing equipment before I bring it into the shop. Like the ‘tidyness’ of the retractable hose.

I don’t know why I didn’t take a picture after I installed it but I intend to remedy that oversight when I get back to the ranch to complete my Dishy install.

Well, it was actually last weekend but I installed my new grill brush guard-black powder coated from BrokeAnvil Metalworks. I’d always planned to fabricate my own but just never seemed to find the time. Now I can grapple my limb piles for chipping with less concern about punching through my...

As have I-been waitlisted for one at Sportsmen’s for months-not going to pay a huge premium just to get my hands on one-I’ll wait until Ruger gets up to full production and shipping. Sure is a pretty rifle and getting great reviews

Follow up-set up system temporarily ( as none of the mounting options I pre- purchased would give me ‘adequate’ view of the sky)-system linked up fairly quickly and is giving me reliable 100+mbps download and 20ish mbps upload. Waaaaay better than HughesNet-actually could stream Prime Video with...

FWIW, I bought a Victory 8” chipper 2 years back (it is basically a clone of the Woodmaxx 8H). Bought it as the other two brands I was considering at the time either had very long lead times with no committed ship date or a waitlist where you were notified via email when stock was ‘available’...

Just got my email notification from Starlink after a 1 1/2 year wait. Cant wait to get it installed and cancel my horrible HughesNet service. Looking forward to uninterrupted video streaming. Will operate in parallel for a bit to make sure it’s reliable enough.

I have the Titan grapple on my LS. Very happy with it-it doesn’t use the same grade of steel as the EA ( or other pricier brands) and is, as a result, heavier-which does impact lift capacity but has not limited my usage thus far. I suspect you’ll be satisfied with the Titan product in your...

It really isn’t that hard to do without losing more than a quart or so of fluid. I did my 50hr service a couple of years back ( did not do the vacuum trick ) and measured less than a quart of fluid loss. Comes down to having everything staged so that there is very little time between the old...

Fwiw- I bought one of their scanners for my XR4155. I had a very satisfactory interaction with them. The only delay i experienced was when I was asked in a follow up email which diagnostic adapter I needed. Being remote from the tractor, it took about 3 weeks before I could confirm the type. I...

I drove both when I was evaluating tractors-I’m sure I could have gotten used to the Kubota treadle however the 2 pedal system was immediately comfortable for me. I ended up with an XR4155HC based on my ‘bang for the buck’ spreadsheet evaluation.

Frigidaire is owned by Electrolux and has been since 1986. Was originally owned by GM, then White Sewing Machine and finally Electrolux. Electrolux bought GE Appliance in 2014 for $3.3 billion.

I have the Dewalt 20v that I use as a ‘prep’ saw for my wood chipper. More than adequate for reducing limbs for easier feeding in to the chipper.