Search results

Results 1 to 20 of 20
  1. A

    MF65 dipstick markings

    Hi all. Have a question for anyone with a MK1 65. Could anyone please tell me the measurements on where the high and low oil marks should be? My dipstick is a bit corroded and I can only see 1 mark on it. Not sure if it only has 1 or is meant to have an add and full? Not sure whether to trust an...
  2. A

    MF65 hydraulic pump control valve

    Hi all, I have just resealed my hydraulic pump, and the control valve has me stumped. I didn’t pay as much attention to it as I should have. I have a new control valve and it comes with 3 sealing washers, but watching a video on a rebuild the girl in the clip says you only need 1 washer? I can’t...
  3. A

    Wiring chart for JD 3350

    Hi. Would anyone possibly have a wiring chart for a 50 series. My 3350 has some swapped wires and I’m looking to get all the dash warning lights working again. My TM doesn’t show the colours or area the sensors are. Thanks.
  4. A

    3130 vs 4430

    Hi all, has probably been covered somewhere but I can’t find a comparison for looking, wondering is there a lot of difference between the European 3130 and a 4430. Apart from the increase in hp is there a lot of size difference? Looking at a bigger tractor for my disc mower and doing a small...
  5. A

    MF188 reduced lift capacity

    Hi all. My favourite old tractor is having problems lifting to the capacity specified. I think the lift capacity is 4550lb (2063kg). It it gets to about 1000lb now and relieves. Not exact but around that. Where should I start looking? I think the relief valve bleeds at 2900psi. I have put a...
  6. A

    Jd 2040 vs 2040s

    Hi all. Looking at a 2040s with a loader as we are now requiring a loader on the farm. What is the difference between these machines other than hp and age?
  7. A

    MF188 relief valve issues

    Hi all, I recently lifted a heavy load, or medium load on a job way out from the arms and while moving the trailer under the load the pump or relief valve started squealing and the load dropped a bit. Have I ruined the relief valve? Now it seems to be noisy with even a light load on the lift...
  8. A

    Oil & Fuel  Oil capacity 2130 different

    Hi all. Just changed a lift pump out on the 2130 and dropped the oil as it had been taking on diesel. The book says 9 quarts oil capacity. Can anyone tell me why mine only took 6.5 quarts? I did not change the filter and verified the dipstick is correct AT21534 stamped on. Also verified the oil...
  9. A

    Cav injector pump numbers

    Hi, I have a Massey 188 which has a badly leaking injection pump. I think I have found a kit to reseal it. Cav DPA pump. I also have noticed a slight leak on my JD2130 tractor. It has a cav pump also. Will this be the same kit/ part number? I figure I may as well save on freight and get two kits...
  10. A

    MF188 charging amps

    Hi all. Just installed a new ammeter in the 188. Does anyone know what sort of amps I should be seeing? Looks to be about 12 on a 30 amp gauge. Is this correct? I am getting about 15.2 volts from the generator at the regulator. I adjusted this regulator some time ago when it was not charging and...
  11. A

    Oil & Fuel  2130 fuel pickup problem

    Hey guys. Have not pestered for a couple weeks so I have another question. 2130 has been going well, then stopped today. Thought it was out of fuel. Put 4 gallons in, primed it and it ran for about half a minute. Checked the tank it was about half full. Primed it and ran all the way home about...
  12. A

    3-Point Hitch  JD 2130 load control arm fouling load shaft install

    Hi all. Originally had a thread running from purchase of my new JD 2130. I am currently working on 3 point hitch problems so will continue thread in correct place. My load shaft seals are leaking. I have managed to find what I think are the correct seals after Tech told me there have been 16...
  13. A

    John Deere 2140

    Hi everyone. Have just purchased a JD2140 after being a red tractor man for years. Haven稚 had it freighted to home yet. Good, bad, ugly? Anything to keep an eye out for? Will need to find a manual for servicing. Cheers.
  14. A

    Forks  mounting a forklift frame to front of tractor.

    Hey guys. My old forklift has finally packed it in. Have been limping it for the last year. Old jigger is not worth an engine rebuild so I was toying with the idea of mounting the fork frame on the front of an old 65hp fiat. Heavy tractor should handle it and won稚 be lifting excessive weight...
  15. A

    Fiat 650 3pl arms raise with no weight

    Hey guys. Have a problem with my fiat 650. Not sure how many people have these tractors. Not the greatest model made but it runs well. The lift circuit is really pretty average truthfully but I can put up with that. What is driving me mad is the fact that the 3pl arms lift up to max position...
  16. A

    MF188 wiring diagram

    Hi guys. Long time follower but haven稚 posted much. I am chasing a wiring diagram for the lighting circuit of a Massey 188. Mine has been cut to pieces by a previous owner so there痴 a lot of wires connected to nothing. I recently got a new generator and got the regulator sorted out so it has...
  17. A

    Mf188 wiring diagram

    Hi. Would anyone be able to help with a wiring diagram of 100 series tractors? When I bought mine it had been cut and shut and bypassed in every place possible. I will get a new loom I think but it would be good to know what colours are meant to go where before I start. Cheers all.
  18. A

    MF188 headlight upgrade

    Hi guys. Just wondering if anyone has found an led light that will fit the original headlamp shrouds of a 188 tractor. Have been looking online but haven稚 found anything yet. Surely someone has made an update to the candles they burned???
  19. A

    MF188 generator regulator issue

    Hi guys, first post, hopefully it痴 in the right spot.... I have a MF188 that has been very reliable over the last two years. However now I need to get it registered so I have to get the lights etc working. A while ago I replaced the generator but still have no battery charging input. Not sure...
  20. A

    New member from Australia

    Hi everyone, just putting a post up to let you know I have joined the forum. I知 from Australia and have a small farm with hay and cattle. Lots of old implements and a Massey 188 & Fiat 650 special. Have done many a job on the fiat but very little on the 188. Will be putting a post up shortly in...