Search results

Results 1 to 200 of 364
  1. Dman1981

    Ford 555C boom/dipper

    Those are circuit reliefs or protection reliefs in case you push or pull something to hard cylinder will not bend rod or break something you have to adjust them by putting a hand pump on fitting into valve and pump it up till it goes off at pressure specified adjust accordingly
  2. Dman1981

    Kubota 3450 Owners, Clutch

    Takes a couple hours to split one it's not a big deal
  3. Dman1981

    Ferguson 65 perkins 4.203 cam gear to shaft placement

    Well good when you get it together and head on I would leave front cover off when you get rocker assy on turn it over really slow To make sure one tooth will have valve hit piston Better safe then sorry
  4. Dman1981

    Hydraulic hose prices (unbelievable !)

    Off eBay old one had dies also 1k Will get you more info is at yard
  5. Dman1981

    Hydraulic hose prices (unbelievable !)

    Bought my own hose and fittings and hand pump crimper cheaper than making four hoses yep it's insane
  6. Dman1981

    MF 1010 4WD Hydro rear wheels / rims

    If center is ok have a rim welded on it it's not heavy tractor
  7. Dman1981

    Ford 555C boom/dipper

    Pressure check and a flow meter
  8. Dman1981

    Ferguson 65 perkins 4.203 cam gear to shaft placement

    Should be a line on cam that lines up to gear When four is rocking adjust one When three is rocking adjust two and so forth
  9. Dman1981

    Kubota 3450 Owners, Clutch

    Don't wait to split till eats thru fingers Just saying
  10. Dman1981

    Massey ferguson radiator

    Part number points to mf285 Should have 4 cylinder Perkins 318 Had a line on one but you took care of it
  11. Dman1981

    Massey ferguson radiator

    Is obsolete it changes to m93 What engine does your tractor have
  12. Dman1981

    2655 Air Conditioner went Boom

    They can be sticky little things but yes they usually stop at txv but yes everything on the downside would need to be flushed
  13. Dman1981

    2655 Air Conditioner went Boom

    It's in the filter drier assembly is just a bag in there with little beads absorbs moisture but if it is in place where it vibrates constantly will break insides apart I know on a tractor right but most of the o es I moved they had them mounted to engine which was Rubber mounted and shook...
  14. Dman1981

    2655 Air Conditioner went Boom

    they have high low switch on them It should turn off before relief goes off In theory The other thing I have seen is the desiccant in the drier busts and puts little beads everywhere down stream Have had to remount them in less shaky spots
  15. Dman1981

    2655 Air Conditioner went Boom

    Put gauges on to read pressures if they are not over relief could be bad. Pump will cycle when refrigerant is low
  16. Dman1981

    MF135 Cylinder Head Rear Core Plug

    You don't want to turn the engine over because gear can then go thru cover But just make sure pin and groove line back up when installing All will be good once you see it
  17. Dman1981

    Mahindra 5570 no start

    Did you check continuity of fuses or just look and see if blown Had one on a kubota looked good but no continuity
  18. Dman1981

    Bent Loader Rod (Mahindra 2545)

    I have straightened many rods just don't do it when it is really cold have a tendency to snap
  19. Dman1981

    Govenor Help!!!

    Put the spring back On Don't know about your engine but the kubotas I have worked on had a spring you had to take off and out back on to pull injection pump went to governor mate just an idea
  20. Dman1981

    M9540 loader question

    How many hours on it have you changed hydraulic filters pump sucks off them all equipment is faster when reving up
  21. Dman1981

    Help. Dunham cultipacker

    Still need to put a cap on it to hold in but you can make that or they might sell cap also
  22. Dman1981

    Help. Dunham cultipacker

    https://www.sweettractors.com/New-Cultipacker-Octagon-Wood-Axle-Bearin-p/cultipackerwoodbrg.htm
  23. Dman1981

    Massey ferguson 175 mutipower by pass

    Multipower pump is driven off three point pump so if blocked off will load system or go boom boom which will cause some kind of situation just saying 😉🚜
  24. Dman1981

    MF 240 stuck gear problem

    Part 32 and 39 I have seen broken and cracked 38 is the interlock supposed to keep them so you can't get stuck in gear
  25. Dman1981

    MF 4255 powershuttle 24x24

    If I remember right discs are worn don't know how many hours you have on it but changed a few of them usually took care Of problem
  26. Dman1981

    Error Code P-208B, New Kubota Tractor, less than 25 hrs use

    Tool These out of m5-111 book if dealer thinks it may not be a warranty thing
  27. Dman1981

    Voltage regulator

    Yea put on real alternator with one wire get rid of rest
  28. Dman1981

    Ford 4000 power steering

    Yes your control valve is on cylinder if it is over tightened it will stick and stay on causing oil to get hot Or piston seal is cut and steering it will do same thing from bypassing oil Will still steer but be hard because it is power assist not power steering
  29. Dman1981

    MF 240 stuck gear problem

    Get the pin for gear shift lever first I will try and get you pic of interlock on backside so you can see it
  30. Dman1981

    Error Code P-208B, New Kubota Tractor, less than 25 hrs use

    The m5-111s I work on had a update on def tank systems not sure if it was same code they replaced whole tank assembly as a unit
  31. Dman1981

    MF 240 stuck gear problem

    You could try changing inter lock first if I remember they wear but if rods are worn might not make any diff have also Seen them broken
  32. Dman1981

    MF 240 stuck gear problem

    Still have to pull top cover interlock Is in diff side
  33. Dman1981

    MF 240 stuck gear problem

    Have to pull trans to change The forks on those rods come Out the back
  34. Dman1981

    MF 240 stuck gear problem

    Quit shifting so fast or replace components but if you still shift like you are racing a few years will do same thing years of experience talking
  35. Dman1981

    MF2606H

    sorry I did not see this earlier but high pressure will cause that kind of explosion have seen on power shuttle transmissions many times valve sticks gives it 2000 psi instead of three hundred and boom boom so the should be replacing a pressure valve or manifold that runs pressure they do it...
  36. Dman1981

    Massey 1547 hst question on trans fluid and gear range

    Low range for long hard pulls High is for roading
  37. Dman1981

    B 2910 Hydro oil level

    Burn it a little
  38. Dman1981

    1985 Massey Ferguson 255 lift problem

    Could also be linkage under covers rocking lifting linkage moves levers. or a sticky control valve. without pulling cover or screen I can give you lots of scenarios screen is easiest
  39. Dman1981

    1985 Massey Ferguson 255 lift problem

    If that screen is dirty Will keep that from working is suction side. you can drain oil and reuse it also. Is a cork gasket on it if Your careful you can reuse it with a little silicone Clean it really good with brake clean and re install same way you took it out
  40. Dman1981

    KUBOTA L 2850 blackout

    Did you try jumping starter just make sure everything is neutral Also if it's a clutch unit can pull start it fuse is usually right before starter have to pull side panel
  41. Dman1981

    mf471 wiring harness

    You can't sluice it back together they have some nice solder joints now
  42. Dman1981

    Ford 4000 power steering

    Sounds like control valve is not centering Or piston seal is cut
  43. Dman1981

    1985 Massey Ferguson 255 lift problem

    Are You talking about the screen in the bottom Of pump you can clean it's metal? An easy check is to pull standpipe cover And with a rubber tip air nozzle blow air in it with levers in the up position.if you hear a lot of bubbles could be rings valves and orings on pump it's a lot easier to...
  44. Dman1981

    JD 5400 Hydraulic power issue

    Found this from a older Post 1996 year tractor number one is relief valve
  45. Dman1981

    JD 5400 Hydraulic power issue

    First question does your loader have its own valve? If it does then there is relief valve on valve If it runs off tractor hydraulics then it also has a relief valve so if you have remotes check tractor relief first. Can be done at remotes one hose with coupler, if it is ok then tee into loader...
  46. Dman1981

    MF135 Fuel Gauge and Sender info

    bought a guage and sender on eBay Put in my 30b I got running works great when full says full when empty tractor dies😉🚜
  47. Dman1981

    JD 5400 Hydraulic power issue

    you've said the magic word a few times power find your relief valve pressure test it and adjust it most are adjustable could be. Few other things but a good place to start
  48. Dman1981

    massey ferg 65 hyd pump

    anytime
  49. Dman1981

    massey ferg 65 hyd pump

    I have used the parts off old pump to new one. pumps are all the pretty Much the same just different applications Have swapped shafts end plates some have nuts with snap rings just make sure everything turns ok when putting back together
  50. Dman1981

    massey ferguson 4610 ac repair

    Is the heater core with it also makes it harder to clean. On kubota m5s I pull out heater core and then flush and blow gently not to bend fins over. same way with wackers I have worked on They make terrible filters for the equipment dirt gets in everything Always make sure drains are clear also🤣
  51. Dman1981

    Hydraulic Oil cooler for Kubota L5450DT

    Found this one he wants 200
  52. Dman1981

    MF30 Instant reverse tractor Sudden failed to move

    That's all good Just don't force it together if it has 1/4 inch to go and won't slide in torque converter ears are on top of pump it must slide all the way In Before bolting it up I would always use a dial indicator to true converter, made pump bushings last longer is all Reason we used...
  53. Dman1981

    Kubota M7040 4WD Utility Tractor Hydraulics

    I have replace quite a few of these Shafts have sheared gears disintegrated. Not cheap either I have both pumps used, they are for a m9000 but I am pretty sure same thing let me know
  54. Dman1981

    Hydraulic pump on farmpro 2425

    So you can use orings in some cases but you still need to not have them to thick. Did you get this pump working yet?
  55. Dman1981

    MF30 Instant reverse tractor Sudden failed to move

    Do you know how to dial torque converter in? They also make pump kit comes with rubber seal torque converter seal and bushings for pump
  56. Dman1981

    Independent PTO problems

    Since I know of nothing else that pulls the lever when it's running and Pto uses suction from three point pump why not pull it brake clean the hell out of it and see what happens
  57. Dman1981

    Independent PTO problems

    is it a aftermarket screen ? I have been working on masseys for forty years both times it happened it was on the suction side is oil permatrsns compatible
  58. Dman1981

    Massey Ferugson 50C backhoe parts (54a attachment parts)

    Sent a note to a buddy he will Put it on locator if he finds something I will give you his number
  59. Dman1981

    Hydraulic Oil cooler for Kubota L5450DT

    Thanks will call him Monday
  60. Dman1981

    MF30 Instant reverse tractor Sudden failed to move

    Thing should have been Leaking some oil and making a little noise nice
  61. Dman1981

    Hydraulic Oil cooler for Kubota L5450DT

    Give me dimensions I will call My buddy at agco he has lots of used parts old cooler Of a industrial tractor might work
  62. Dman1981

    Independent PTO problems

    The screen is plugged
  63. Dman1981

    Hydraulic Oil cooler for Kubota L5450DT

    use your imagination call some used part houses. as long as you can mount it up some how and adapt fittings will work most coolers should not be running more than 300 psi and lot of aftermarket stuff can be adapted
  64. Dman1981

    Kubota F2400 Overheating - Thoughts Please

    Does it have fan shroud is the fan the right size all good questions
  65. Dman1981

    MX5100 steering problem

    Hydrostatic steering will keep turning if you hold it against the stop the whole time once you reach full turn you need to back off otherwise it will open relief valve the whole time you are turning Some do have valves for shock reliefs which have orings but most cases they are not rebuildable...
  66. Dman1981

    Kubota M7040 4WD Utility Tractor Hydraulics

    Have had the steering and trans go away because of filters oil was good but he did not ever change filters
  67. Dman1981

    LS 3025 front axel fluid

    gl5 is better protection for extreme pressure I use synthetic in all my customers front axles my weed abatement guy is 1k hours a year No problems
  68. Dman1981

    Anyone have a clean way to drain the antifreeze out of a GC engine block?

    They make test strips to check just pull a little out and refill if it is low use ell and be done with it also.unless You run 1k to 2k Hours a year waste of money My tractor is twenty years old 368 hours changed once is still good after The years no leaks no corrosion But everyone gets to...
  69. Dman1981

    MF3165 Alternator Type

    I have always used ac delco for them cheap and readily available you can use the one wire self Exciting or the three wire with plug Just have to run a wire from key or oil pressure switch to excite alt Tractor is almost as old as I am
  70. Dman1981

    Wheels dont turn

    More info
  71. Dman1981

    California Transportation Laws / CDL / Motor Carrier Permit

    That's why you buy the f350 As Long as gvw is under the threshold your good I have a few customers haul that way
  72. Dman1981

    Question for those who live in California

    Stay put the freeways are Overloaded now and with all the illegals that I am helping house we are Good
  73. Dman1981

    Mf265

    That is the drain size I believe fill plug is 1/4 pipe
  74. Dman1981

    Mf265

    1/8 pipe gear oil
  75. Dman1981

    MF230 VS MF231?

    Early late models of course 230 orbital steering valve with cylinders 231 is like the 240 250 series I worked on, power steering assist Has arms that run to steering arms 230 also had small ring gear and pinion and drum brakes The 245 was basically the same unit but wet brakes and bigger...
  76. Dman1981

    L3940 Engine Valve Lifter adjustment

    Is it low on power does it rattle do you change the oil regular 800 dollars lot Of money for a valve adjustment Got 3000 hours on couple m5-111 still running strong Even with def
  77. Dman1981

    massey 50hx battery replacement?

    Used group 24 batteries two of them
  78. Dman1981

    L2900 GST Shifting Problem

    I can tell my eyesight sucks and spelling lmao
  79. Dman1981

    L2900 GST Shifting Problem

    Broken sealing rings believe they were not Teflon if you did not grease them up good to keep 'em shrunk dow you could clip it
  80. Dman1981

    Hydraulic pump on farmpro 2425

    Also turning pump motor and tighten a little bit at time so it does not bind do nkt Over torque
  81. Dman1981

    Hydraulic pump on farmpro 2425

    Are the seals you talking the orings or quadrings for the body if You have old ones go to a seal place a match them up or take seal kit back
  82. Dman1981

    TO35 Lift Problem

    You can pull top cover and air check cover and pump piston seals dont Usually cause slow lift but will Leak done get a it manual before pulling cover save you some time picture are great Once cover is off put standpipe back in and air check with oil in so you can see where bubbles are Coming...
  83. Dman1981

    Ford / NH 545D Industrial Tractor - looking for owner experiences

    Must not be any hours on them my customers put 1000 to 1500 hours a year on them grading hauling and moving dirt for tilt ups would do them once year depending on operator of course some grease them most don't $$$
  84. Dman1981

    Ford / NH 545D Industrial Tractor - looking for owner experiences

    Yes and I have rebuilt hundreds of them and a replaced axle housings and had them repaired when bearings explode and no longer have a nice place To hang out same with housing
  85. Dman1981

    Ford / NH 545D Industrial Tractor - looking for owner experiences

    4x4 the seals leak if they have not been greased king pins wear out also if you wait to long is expensive repair last year did two repairs were 6k a piece and I am cheap dealer Would have been 10k. if tractor is tight they run all day long though Still easy to repair. Fermec 650b are also very...
  86. Dman1981

    Replacing Tachometer, compatibility question

    Had a 1978 mf 30b bought all gauges and cables on eBay all Worked good it's old just needed to sell otherwise would not have even done that
  87. Dman1981

    Mahindra 2565 AC Condenser

    You can buy anything You want on eBay and Amazon jsut do the research dealers are Crazy my kubota m5 was 1k eBay couple hundred
  88. Dman1981

    1998 Massey 231

    If you have ipto you have to pull top cover to replace coupler do not have to split it they usually spin out the splines changed lots of them on four wheel drive units On the 230 model also saw a lot of ring gears break if it has wet brakes has bigger ring gear and pinion
  89. Dman1981

    Ford 1700 - 3 point lift control loose on the way up

    On the the rod yes just be careful sometimes the nut is frozen don't want to create more situations
  90. Dman1981

    Ford 1700 - 3 point lift control loose on the way up

    Tighten nut On inside of linkage close to Cover believe were belvue springs on it should be able to see It From back of tractor
  91. Dman1981

    Jinma with BH 7600 backhoe Problem leaking fluid on Backhoe controls

    Good Oring and seal place will have what you need if spools are leaking
  92. Dman1981

    492 Steering Issue Part 2

    suction side screen also need to change filter front pump Is steering pump You can also crack pressure line to see If oil is present https://parts.agcocorp.com/us/en/apbsearch/model If this link works can look up parts
  93. Dman1981

    Allmand 425 Backhoe Cylinder

    Been building cylinders for forty years if you need everything perfect with no little sweat marks you can have rod made if can't find cylinder Worked Mainly for owner operators if it got a nick that was protruding I would file and buff it would get a little oil but not bad enough for him to...
  94. Dman1981

    Need to replace altenator on 1986 1210

    If you have any skills buy a one wire delco and make brackets
  95. Dman1981

    Independent PTO problems

    I have seen screens that look ok but not have also had em when you rev them up would stop working also and implement drop create a vacuum from not enough oil
  96. Dman1981

    Independent PTO problems

    They do run off same sump a little tube form Pto pump to suction side Of three point pump it is a cleanable screen no need to change it I would still clean it
  97. Dman1981

    Independent PTO problems

    There is a screen on that pump is a three hole plate on bottom of differential the Pto pump runs of a gear on the three point pump
  98. Dman1981

    Independent PTO problems

    Did you clean sump screen just because they look clean is not always true
  99. Dman1981

    MF 230 steering is not working

    Oh just saw you used 46 fluid atf works better all I have been putting in them for forty years then you also know when you have steering leak
  100. Dman1981

    MF 230 steering is not working

    fill it up the. Steer it then fill it some more there is filter in the can Also if they blow up it is hard to fill while running if it is really dirty could cause slow steering
  101. Dman1981

    MF 230 steering is not working

    This is a ag mf 230 with the steering pump bolted to front cover
  102. Dman1981

    Mf 1260 3 point

    It's usually right under seat sticking out unless it does not have one rod connected to a knob of some Kind usually can see it on
  103. Dman1981

    Mf 1260 3 point

    Do those have a shut off valve on front of top cover maybe it is screwed in
  104. Dman1981

    MF30 Instant reverse tractor Sudden failed to move

    More than likely but the crud is everywhere could have broken sealing rings also I would pull them make sure they are not stuck pins will stick in plunger
  105. Dman1981

    MF30 Instant reverse tractor Sudden failed to move

    iOS screen still intack So the two bolt heads on side of trans regulate fwd and rev pressure are Spring Loaded with a spool valve a pin inside shims under springs for pressure top bt Is to cooler and filter screen in filter also
  106. Dman1981

    MF30 Instant reverse tractor Sudden failed to move

    Three point works off trans So are there any little pieces in the screen
  107. Dman1981

    MF30 Instant reverse tractor Sudden failed to move

    Quick question does scraper Still Go up and down If it Does. you could have broke coupler from trans to pinion which can be replaced they left hand side cover
  108. Dman1981

    After Market Front End Loader 1978 MF 230

    https://www.tractorhouse.com/ This is something like you will be looking for this one runs off aux pump if it has one or three point pump slow but works they also make a kit for font mounted pump with shaft and coupler off front pulley had to have hole front axle pin
  109. Dman1981

    John Deere 1445 hydraulic float issue

    Yes I use heavy duty assembly grease but anything will Work to be honest use what is available I do this for a living so have access to many different Lubes
  110. Dman1981

    John Deere 1445 hydraulic float issue

    More than likely it is rusted up inside of of cap take it off some slide off others need to be popped off or pull spool with it has spring and detent balls in it so if you do try and take it apart wrap a rag around it just in case parts come flying out
  111. Dman1981

    1974 MF150 Diesel Won't Start Without Jump Starter

    Cheap voltmeter from anywhere will check your voltage also a little screwdriver to back of alternator if it is charging will grab it Creates a electromagnet effect
  112. Dman1981

    1974 MF150 Diesel Won't Start Without Jump Starter

    Maybe when you get it running see if it is charging just a thought
  113. Dman1981

    1998 Massey Ferguson 231 Power Steering Control Valve Rebuild Kit

    It's where it bolts to steering shaft you can use orings too but they were square did not come In kit from Massey back in the day
  114. Dman1981

    1998 Massey Ferguson 231 Power Steering Control Valve Rebuild Kit

    Ah the old power assist control valve does it come with the quad rings also?
  115. Dman1981

    Oil Change intervals?

    Two oil changes in twenty years Techron fuel additive always starts no issues at all little over four hundred hours
  116. Dman1981

    John Deere 1966 4020

    When I was a kid we had a du Al loader on our John Deere seen them at auction sites just have to figure out which one fits yours
  117. Dman1981

    Oil filter cover plates?

    Smoke a little smoke drink a little drink 😉🚜
  118. Dman1981

    Backhoe Transmission Will Not Engage NH 555E Backhoe

    Most of those shuttle valves have manual pin you can push with pick to see if you have electric or oil problem manually pushes valve across to engage trans just because you have power does not mean spool is moving also have had a few of them stuck over the years
  119. Dman1981

    Why Can't Someone Make a Good 12' Batwing Cutter?

    Buy a good fifteen footer used and modify for your needs winter project
  120. Dman1981

    The guy that put the engine internals together says "The rings are not seated yet end the smoking is normal. Just give it a couple hours of work"

    Well I have turned the wrench for over forty years overhauled 1000s of engines never used abrasives to seat Anything. I use a light oil not engine oil usually marvel oil Stuff gives enough lube till running and engine does the rest no smokers no boom boom no blow by They run as long as customer...
  121. Dman1981

    What happened here to my tire?

    Pale of tire soap is cheaper than a cheetah and less noisy
  122. Dman1981

    Help with ROPS on Branson 4220i

    Just tell welder You will sign a waiver does he work for the city🤣
  123. Dman1981

    Starter for Kubota L1500DT

    fix it
  124. Dman1981

    Starting problems with John Deere 250 skid loader

    Start wiggling plugs and checking grounds even check positive cable high resistance can cause problems Also
  125. Dman1981

    Massey Ferguson GC 2300 bent steering box brackets :(

    Adjust your stops if it has any also check toe in If you are turning hard and hit something and stops are not adjusted right it Would push cylinder
  126. Dman1981

    Correct use of shuttle shifter

    Well for fwd reverse anyway still need to clutch to shift gears 😉
  127. Dman1981

    Correct use of shuttle shifter

    If it's a hydraulic shuttle no need to use clutch Manual shuttle you have to clutch
  128. Dman1981

    Mf65 steering column

    Just saw this slip can be taken out with nut and adjusting screw on side of box make sure it stays smooth if you have power steering up front, there is a master spline for arm and shaft
  129. Dman1981

    massey industrial 2200

    Gas or diesel
  130. Dman1981

    231s Massey

    Internal hydraulics are slow of three point works good and pto works good pumps are Probably ok There is a screen on pump it comes out bottom three hole cover on bottom of differential have to drain oil of course They used to make a kit for those so you could run front pump off crankshaft...
  131. Dman1981

    Farm All JX65 Bush Hog loader M446 Joy stick problems

    If it was Me I would take it to a good machine shop and have metal one made
  132. Dman1981

    Terex/Fermec 650B slow moving

    I can be your manual;) Fill Is under hood on left side dipstick is there also Might also be one on left rear side cover dipstick that is Has suction screen on right side right before pump it is aluminum housing if you take this apart be very careful threads pull easily if they are pulled can...
  133. Dman1981

    MF 135 fine tuning lift controls conundrum

    also on the draft control adjustment Screw measurement against back of cover make some it just touches don't use book measure That way if you are backing up it will lift notated what pretty Much eliminating draft
  134. Dman1981

    MF 135 fine tuning lift controls conundrum

    Also make sure your arm bushings are not worn out will effect operation
  135. Dman1981

    MF 135 fine tuning lift controls conundrum

    You have to put a small vise grip or spacer on dash pot rod so it stays extended pull cotter pins will need to lift arms a little more also Center the position and draft control plates also looks like they are from pic you can fine tune a little with that after cover is on And then make sure...
  136. Dman1981

    NH TC45D No start. Single Click/Clunk and nothing. Seized Engine?

    When a crank is turned, at the edge of rod and main journals it should Be like picture lots of you tube videos also Same Goes for when it is bored for sleeve cut for sleeve recess cannot be square cut other wise sleeve will crack and get sucked into pan Experience talking. Hate doing stuff...
  137. Dman1981

    Shocks

    Get specs and call auto parts
  138. Dman1981

    231s Massey

    Does it have front mounted hydraulic pump or Does run three point pump plumbing Would be under seat What loader is on it for so thave it s own reservoir which would be for a front many questions Need more input
  139. Dman1981

    Case Agri King 1370 - Are they any good???

    Engines were golden when taken Care of as most things But trans was pricy just stuff I remember from the farmers who ran them
  140. Dman1981

    Brush hog stump jumper/blade carrier mod for bolts.

    Weld in hex assembly for mower blades
  141. Dman1981

    Ford 4500

    When I worked on them new we called Them dinosaurs
  142. Dman1981

    Brush hog stump jumper/blade carrier mod for bolts.

    I agree with you were **** But the hex heads seemed to work really well three seasons just had welds break on one Just welded it back in
  143. Dman1981

    Shear pin nightmare

    Heres my forty Years Of turning wrenches taught me. **** gets loose wears out not everyone has tons of cash to stick into stuff if you do awesome so I fix things make them last another five or so Since most here are not owner operators so you do little things that keep 'em rolling I do the...
  144. Dman1981

    Shear pin nightmare

    My best friend when I was kid on the farm was aluminum shovel When I told dad I was cold he would hand it to me and say go outside and get warm 😉🤣🚜
  145. Dman1981

    Grease fitting question

    Drive out bushing and turn it or get new one It spun for a reason though
  146. Dman1981

    Shear pin nightmare

    That's for sure enough loose nuts behind the wheel already
  147. Dman1981

    2001 case 580sm

    Go away when it warms up the oil that is 🚜
  148. Dman1981

    Shear pin nightmare

    Leave your shear bolt a little loose use a stover nut or double up nuts Will bend but not break right away anyway. Tightening them down makes them pop
  149. Dman1981

    Stihl 036 Hard Starting

    **** my bro in-law cannot even start his lawnmower If the tv could Mow he'd let it Mine kicks me also but fires up
  150. Dman1981

    BX2200 starts and runs in START, but not RUN

    Your on you way to greatness My grandson can't keep my running either
  151. Dman1981

    Loader for a 1105 Massey

    They are just not built very heavily compared to a industrial loader We Sold them to dairies for Pushing manure and loading feed They flex a lot Once the industrials came Out with 4x4 they went that way Still broke em but took longer If you are Looking to move a lot of dirt and material A...
  152. Dman1981

    Loader for a 1105 Massey

    I believe it was mf 246 loader On those Check with salvage places or auction houses Have seen a couple Or just find a good industrial loader and weld away The agriculture loaders are pretty weak Has a radial piston hydraulic pump so you have plenty of oil to run it If it is working properly
  153. Dman1981

    Brush hog stump jumper/blade carrier mod for bolts.

    On the bigger bushhogs bat wings the new pans come with a weldable Hex sleeve for blades Part number 50076706 sleeve Bolt kit is 50076475 Bush hog part numbers
  154. Dman1981

    Front Hydraulic snow blower slows down when warm

    Heat only a factor if one piece of the pie is doing it Hydraulics in the desert run 220 Or more that's with coolers
  155. Dman1981

    New tires stretch alot?

    Yes
  156. Dman1981

    Student Loan Debt?

    There is no such thing as free or government money It all Comes From taxpayers Who work not welfare or people on disability If he is forgiving the debt just means they are going to take more money from working class In ca there are more people not working than working And it keeps getting...
  157. Dman1981

    Front Hydraulic snow blower slows down when warm

    Without flow meter Or gauges it's just parts replacing
  158. Dman1981

    Is black smoke a problem while snowblowing

    Governor is working and giving you the fuel to Let you do Your job
  159. Dman1981

    Tractor smoking

    My tractor smoked a lot but I talked it into quitting it breathe better now 🤣🤯
  160. Dman1981

    NH TC45D No start. Single Click/Clunk and nothing. Seized Engine?

    What did radius look Like on journals if they are not tapered when cut or ground will create a shear point and snap We had a machine do a few cranks for us years ago all of them broke
  161. Dman1981

    Tractor can't get into gear

    When you replaced pump did you put coupler back on it is on shaft out of gear drive on back of trans connects shaft to pinion assemble
  162. Dman1981

    Water heater recs please

    My power goes out to much for tank less hate cold showers Gas stays on no matter just a thought
  163. Dman1981

    Tractor can't get into gear

    Need more information do handles wobble around Did you take shift cover off Does tractor move at all Did you put drive coupler back in with cutter pin, put in backwards will fall off 😉🚜
  164. Dman1981

    3-Point Hitch PTO Seal leaking

    3m weather stripping Adhesive sets up nice and hard also
  165. Dman1981

    RTV900 losing power

    Try some heat warm things up
  166. Dman1981

    3-Point Hitch PTO Seal leaking

    Don't miss the white stuff Good luck
  167. Dman1981

    3-Point Hitch PTO Seal leaking

    The only other thing I have done is Find an aftermarket seal if possible sometimes they are a tighter fit Or go back to kubota and see what's up. if you use any type of sealant area must super clean and must sit 24 hours for complete Also check and see how much in and out play is on shaft...
  168. Dman1981

    3-Point Hitch PTO Seal leaking

    Look at your housing make sure you did not push it open or crack it with when you ruined seal
  169. Dman1981

    Replace bucket cutting edge

    Don't know where you live We have a place here called cutting edge supply make you any size blade I want
  170. Dman1981

    Replace bucket cutting edge

    you can order a cutting edge made for your bucket Bolts are like plow bolts recessed in blade
  171. Dman1981

    fuel filter schedule

    I have 360 hours on my tractor Took twelve years changed filters once were clean always has additive for fuel. starts and runs even after months of sitting battery is maintained one battery in that time also don't put in bad stuff don't have bad stuff happen Also has been in a garage it's...
  172. Dman1981

    MF165 Problems after lift cover reinstall

    Did you ever get this thing working
  173. Dman1981

    Massey ferguson 2635 hydraulic issues

    If pump is inside they both suck off same screen in trans Does your loader have front mounted pump off crank pulley or do hoses come from top cover And you have to put it in constant pump The issue would be the same on loader no oil so full of air
  174. Dman1981

    New Injector pump

    If injectors were bleeding off thing would hammer trying to start, to get rid of raw fuel in the cylinder makes Noise bends rods
  175. Dman1981

    Ford NAA

    do you have pressure
  176. Dman1981

    Ford NAA

    Is the pump working sounds more like no oil
  177. Dman1981

    Kubota M7060 skid plate for fuel tank area

    For weed abatement I make a skid plate front to back covers oil pan fuel tank and lines and hydraulic filters Let Me know if you need a pic usually two pieces on big tractors
  178. Dman1981

    Massey ferguson 2635 hydraulic issues

    Do the loader and three point run off same pump If it has internal pump for three point should be a little cover on bottom of differential the screen for the pump is accessible under that cover if it gets plugged up enough Three point will raise at idle but when you rev it creates a vacuum...
  179. Dman1981

    Ferguson TO 30 3 pt wont go down

    Control valve in pump could be sticking or linkage in cover is binding you can pull side cover and and move linkage to see if control valve is working and then see if you can manually move it Buy a repair manual on eBay or wherever you find one give you better picture of the system pretty...
  180. Dman1981

    Warranty misleading

    There are no circuit relief valves in compact or most ag equipment So when you go over the rated pressure of the system something will give way
  181. Dman1981

    MF165 Problems after lift cover reinstall

    The one lever is not sitting on the roller pry spring back and see if You can get it back on The quadrant assembly should have two rollers one is for draft other is for position control have seen them rust off also then you can repair it or find good used one Most that are that old usuallly...
  182. Dman1981

    MASSY FERGUSON 65

    What engine is in it 203 Perkins or is it a English tractor If it is a 203 only timing is on front gears injection pump has dowel for gear and has slots for a little turning
  183. Dman1981

    Massey FERGUSON INDUSTRIAL 50D TLB

    50ds had opposing swing cylinders
  184. Dman1981

    Tractor smoking

    Yes been using For mainly diesel for a long long long time Cleared up many a fuel issue Plus keeps my gas pumps and equipment always ready to fire up
  185. Dman1981

    Tractor smoking

    Do you put fuel additive in it when it sits? I put Techron in all my vehicles gas or diesel. Keeps them fresh
Top