Search results

Also I have no cab and park inside my shop so I really hear it on shut down..lol

I have an ns5310 and mine makes the exact same nosie on shut down...I never thought much of it tho as long as the tractor works fine...I kinda thought it might be the dpf dumping ash out or something but I don't really know.

The fears of tipping the tractor over are fair but I don't go on too off much off camber stuff with my tractor and if I do I am well aware of terrain and ready to jump..lol..I'm actually more scared of my zero turn lawnmower tipping..

Hahah..cause it would be too easy..did you take your rollbar off as well?

Yes it is..would have worked out fine if it folded in the middle like most of them do

I have an NS 5310 and the damn rollbar is too high for my 8 foot door and too low in dropped position to raise three point all the way..needless to say that damn thing is not on my tractor

The wear ring is all beat up on my snowblower chute...I'm not even sure what it is officially called and I haven't been able to find it online yet...it looked like 1/4 inch thick poly c-channel? I am hoping someone can point me in the right direction..lol..at least snowblowing season is over now...

I did change the engine filter at the 50 mark..it was only the hydrolic and hat filter that my dealer said to wait till 200h

That is interesting to hear that there was no metal in the filters..my dealer said not to worry about filter change untill 200 hour mark on my ns5310. I bought the filters anyways but haven't put them on yet..tractor is at 70hours..these filters cost so much I'm on the fence about waiting a...

I have the same chipper on my ns 5310..you can put whatever you want in that chipper and the tractor won't care..I did have to cut my PTO shaft down and I probably should have raised it up to make the shaft more level but I haven't yet and it ran fine all last season.

I ended up taking the tire off my ns 5310 when I added a second remote..not sure if it could be done without doing so. I had the dealer mech come to my shop to do it and it was an all day battle..apparently it was his first one..lol..and then to top it off I had to change a quick connection plug...

That is very interesting..we have the same motor and fram so I'm guessing my ns5310 takes the same

Following..I have an NS 5310 and am curious now too..lol

Hard boiled eggs

You wouldn't happen to have any part numbers for the HST or Hydro filter would you? My 50hour service is due on my NS 5310 and the dealer was suppose to do it for free as per our arrangement at purchase..however when they came out all they changed was the eng oil and filter and said that was all...

I just came back from a trip to the dealer and they weren't 100 percent sure which HST filter I needed .they had the hydrolic filter..I'm gonna try to read some part numbers off the old filter before I shell out over a hundred bucks for one filter.

I have the same ns5310 tractor and my dealer just completed my 50 hour service..all they did was change the engine oil and filter. I always though I read something about changing the HST filter at the 50 mark too..my dealer told me to change out the HST oil and filter at 200 hours. I also had...

Would the dk5310 manual be similiar to the ns 5310 manual? I have been looking for a copy since I bought my tractor.

I notice a chirp on my 2022 ns5310 as well every once in a while..I never really paided much attention to it and I can't see it creating any problems

It is only one belt for the 6 inch model. I have the 8 inch model wc88

I will be adding wheels to my shipping crate as well for storage. Got about 4 hours on the chipper now and I noticed this am that one of my belts broke and two others were still on the pulley but twisted sideways..not sure what would have caused that 😞

Got mine dropped off as well...my first impressions after using..I'll never be able to cut enough trees down to keep up with it..lol..love thiss chipper!

Looks like it will do the job! Did they have a lift gate to drop it off or did you sling it?

When is yours due to be delivered hughman? I haven't got any delivery dates yet.

I was wondering if we need to be there to unload it or if the shipping company does it..I don't remember reading anything on the woodland Mills site about that...

I agree..I used to cut trees for a living and if that saw was even hinting it was dull I would sharpen it..does anybody know if I can sharpen these chipper blades on my own and what is the best tool process used to do it?

Just put my order in for the woodland Mills WC 88! I hope it chips as good as I'm expecting it too...now to get to cutting some firewood and gathering branches...lol

My new Holland 555E had a large pin to secure the swing during travel. I used it whenever I wasn't using the backhoe part...same with the extendahoe pin

My price was in Canadian dollars is probably were the difference is and I have to pay 13 percent tax to the government unfortunitly

Congrats! Dang I didn't relailze they stripped them that much for shipping!

I'm on the fence about ordering the woodland Mills wc88 chipper right now as well. I was surprised shipping was only 200 bucks too for an all in price of 4827.70 Not too bad for an 8 inch chipper

Usually get all the exercise I need cutting firewood..when I'm not doing that the military dictates my PT schedule..lol..I'm 43 and some of these 20 year old kids have a hard time keeping up!

My 2022 kioti had a seat a seat switch..first thing I did was in unplug it and jumped the tractor side of the switch with a paperclip..way too annoying having the motor shut off everytime I wanna jump off and throw something in the bucket.

Someone with a waste oil furnace might be able to burn it for heat maybe?

Really eh..I did not know that. it is still the best bang for buck as far as a chipper for my 40 acre property go tho I think

Back in thee day when I built over kill Dana 60s for mud buggies if a shaft was overly worn like your descripting I would use a speedy sleeve on the axle to cover the groove..I am sure there are different sizes..I was able to get them at my local seal and bearing shop. Just read your above...

Ah man now I want one of those salaco 10inch hydro feed chippers love the dual feed wheels too..definitly over kill for what I need...lol I will probably end up buying a woodland Mills wc88 tho..it's all I really need and it's made in Canada where I'm from for not too bad a price.

This worries me cause my brand new NS 5310 looks to be the same axle baack there..what year and model tractor is yours? Here's hoping the home owners insurance covers it otherwise what's the point of paying insurance on a tractor! Unless it just fire and theft..

Dang that sucks..do you have warrenty still?

I replaced mine with metal warn hub locks on my 2003 f250..I'm not too sure what that peice is but once you have the locking ring out I would drill and tap like you said and replace the whole hub lock.

The ads inbetween posts are definitly annoying enough to the point I don't want to read the thread!

Not sure but my NS 5310 has the loader control mounted by the seat. There are cables running to the valve spools which I'm not a fan of but I'll take it to have the loader controls mounted convinently beside me.

I heard the nx hst were controlled electronically vs mechanical. This was the main reason I didn't search one out but I got lucky and found an NS 5310 and bought it. The loader does have a guide rod on it but I don't use it as I swapped a large material bucket on the loader as soon as I got the...

So it is ATF automatic transmission fluid in there but prolly not as good as automotive ATF? So confused about all these tractor specific fluids..in the old days I would 100 percent just throw some gear oil in that front axle...

I have had gear tractors and then shuttle shift( including full size tlb) and now this kioti NS 5310 hst...I wouldn't ever go back..love the hst!

I used a shop vac with air hose duct taped to the nozzle forr my shop floor drains when they were plugged. Just bought the property and noticed floor drains weren't working when the wheeler and tractor were melting off there snow. I got everything from nuts and bolts to plastic balls that you...

My kioti NS 5310 I am assuming it is filled with hydraulic fluid

Hoping there might be an oil expert that can answer this but if kioti factory filled my front axle with hydrolic oil could I not use this ATF when I do thee 50 hour service? I was always under the impression that ATF was superior to hydraulic fluid and wasn't used simply cause of cost. I have 3...

On my new Holland 555e it was a broken linkage when it happened to meet last winter.couldnt curl the bucket..I just welded it back up and it's worked fine ever since

If t-6 is no good for catalytic converters, is it still ok to use in dpf equipped tractors or will it plug those up too?

I bought a NS 5310 in October and for the life of me can't remember what my dealer said but is that frist 50hour service free? If it isn't I'll just do the work myself. Thanks

I have a switch on my NS 5310 for that dpf..does yours? I haven't had one happen yet(only 30hours) but what your saying is when it does happen I don't have to hit the switch it just does it automatically? That dpf but always confused me...I do run the tractor at 2500-2600 rpm all the time other...

Not sure if it's the same on your tractor but on my NS 5310 I just unplugged a connector by the seat and used a peice of paper clip to close the connection..frist thing I did when I jumped off the tractor for the first time and it shut off .lol

Does anybody have a digital manual for the Kioti NS 5310?

I bought a kioti ns5310 this past October. I love it. I have had all kinds of equipment in the past including full size backhoes and this little tractor is the most useful peice of equipment I have. I usually always run at 2600 rpm and haven't seen any signs of the desiel exhaust Regen filter...

hi guys. I recently picked up a long neck cincinatti ben h grinder for 50 bucks..i got it all wired up and running but it seems to be backwards from my smaller grinders. This brings me to my queation. which directions should the wheel be running in? mine is currently in counterclockwise amd i...

Hey all.. i have a 77 mf industrial tractor/backhoe...i was using the backhoe yesterday no problem after fixing a couple hoses that bust ( tractor hasnt been used in 2 years). Anyway i went to use it today and the backhoe part isnt getting any hydrolic pressure. The loader works but it seems...

Here is a picture of the spool.. I thought i read somewhere there was a screen or some way of cleaning it out but am not sure which bolt to undo..

Hey all.. i have a 77 mf industrial tractor/backhoe...i was using the backhoe yesterday no problem after fixing a couple hoses that bust ( tractor hasnt been used in 2 years). Anyway i went to use it today and the backhoe part isnt getting any hydrolic pressure. The loader works but it seems...

needed to drain some water from a road i am working on to get to the back of my property so i decided to use a culvert i had around to help drain the spring.. Its a little over kill but it was what i had. there is a small pond/ lagon just to the left of where i am building the road which i...

The time has come where i need to produce cleaner looking welds. I know that my flux core wire welds are soild but they dont look very clean or wet.. The only reason i stuck with the flux core so long was because i received five 25 pounds rolls with my cv 300. I have the gas hook-up on my...

I know that when i was looking at my 5020 i had a hard time finding any video's of the tractor running. I dont know if it is as bad with the other models but maybe we can get a thread going with some video clips to help others who are thinking about buying LS. This isnt a very good video but it...

I am looking at buying a mill and lathe for my shop. I have no idea how to use them or what to look for but i want to learn. That being said i dont need to get a 3 in one ( i have enough space) But this one came my way. He is asking 2500 for it, and has no idea what tooling comes with it..looks...

Cant get more than a minute of straight welding before it jams..At first i thought it was just the roller in the feeder so i swapped that out for the one in the parts machine.. No after a minute or so of welding it pig tails inside the feeder.. The machine works fine for small short welds but...

Starting this thread to keep my thoughts in one place and to get much needed info..The plan so far is to use a 15HP motor with a 16gpm pump, 3.5 inch diameter 2 foot hyd cylinder with the hopes of achiving high 6sec low 7 sec cycle times..My father inlaws splitter is set up like this and is very...

Does any body have the LB3501 or LB3502 Ls backhoe? Just looking for opinions on quality, power etc..Or even how much they are( have yet to call my dealer about it)..My thoughts on it are it is is going to cost more than 10g than i might just buy an old full size TLB..Here is really the only pic...

I have an unopened pail of walmart hydrolic fluid that i used to dump in my old 79 ford's loader..Is it OK to use with my new LS Tractor? I need to change the hydrolic filter for the 50 hour break-in change and was thinking about using it to top off any fluid i might lose..

Tractor is just over 16 hours old..only had it 2 weeks now( havnt even made a payment yet) and i cant use it due to a hydrolic steering line being pinch between the loader mount brackets..It must have been like that from the factory when they bolted it together because i cant see how it would...

Just got a 2010 LS u5020c. Only have 10 hours on it so and it is replacing a 79 Ford 3550 industrial which was tough as nails and had an even strong loader..This new tractor had alot to live up to and i found it to be very good at digging( especially in 4wd) as well as much, much more...