Search results

Results 1 to 11 of 11
  1. Henhouse1

    YM1610D Idle speed adjustment

    Idle speed on this 3T75U has always been a bit low, but now the 3 point is getting weak and I need to raise the idle. Tried adjusting the rod on the throttle at the fuel control lever since throttle has a detent. Thought I had it but it dropped back to original low speed. What am I missing, Winston?
  2. Henhouse1

    1610D Koyker 110 baffled!

    Okay, fellers. Haven't been here in quite a while cause I haven't needed too but she's got me stumped NOW! 1. FEL slower and slower to lift over last year. FEL will drop overnight if left up. Curl is fine. 2.will not lift at idle and very slow at high RPM 3.swapped hydraulic lines at...
  3. Henhouse1

    1610D with Koyker 110: FEL bucket almost inop unless 3 point is in "UP" position.

    FEL "Lift" has been getting slower and slower over months. Was almost completely inoperative until I discovered that if the 3 point is in up position, the FEL lifts normally. The curl is normal regardless of 3 point position. Hydro fluid is in great shape and at the top of the dipstick.
  4. Henhouse1

    YM1610D will not move fwd or bwd any gear or range.

    PTO, 3 pt, most of FEL works. FEL is jerky. 3 pt waits several seconds longer than normal before operating at normal speed. Are these symptoms common for a clogged filter?
  5. Henhouse1

    Koyker 110 bucket curl inop.

    OK guys, thought the old 1610D was dead for sure but is now mostly healed. Trouble started with bucket drooping while bushhogging. Now it will not curl up or down. is stuck all the way down. Nothing at all happens when operating the controls, no drag on engine as is normal. Where should I...
  6. Henhouse1

    1610D will not move any gear or range!

    After solving minor cooling issues, was bushhogging back pasture and had done an acre, noticed loader bucket was dropping. Curled it back up but wouldn稚 stay up. Drove back to barn and parked. Checked hydro level and added 1.5 qts 303. Went back for 10 minutes with same results. Headed back to...
  7. Henhouse1

    ROPs Remnant?

    Guys, is this green structure the lower part of a Factory ROPS system or just part of a factory sunshade? Excuse the blurriness. Stan Henley:confused:
  8. Henhouse1

    Still at home, stir crazy.

    Well, still can't get to work. My son is stuck here, trying to get to Denton, TX..........SSSSOOOOOOOOOOOOOO....... time for a video! Filmed today as my son is learning the joy of driving my YanMartha and is showing me how to "Ghost Ride the Whip" (as our urban brothers call it.) ;0) Stan...
  9. Henhouse1

    Snow  New Redneck Satellite Dish De-Icer

    After clearing the snow from the driveway with my trusty YanMartha, I invented this incredible device. Thought you guys might be impressed. Email me for the blueprints. Stan Henley YouTube - Redneck Satellite Dish De-icing:D
  10. Henhouse1

    3-Point Hitch  Hitch speed control

    I thought there was a lever or knob on the left side of my YM1610D under the seat to control the drop rate of my 3 point hitch. For the life of me, I can't find it and the pictures in my manual are just too dark to see.:drool: Thanks, Stan Henley
  11. Henhouse1

    Newbie here.

    Just got my "mature" 1610D to take over for my JD GT275 which is beginning to tire after 13 years of taking care of 6 acres of grass, pasture, and gardening. Found a pretty good tranny leak after a day of bushhogging. The dealer sent out a Mech the next day and is making it all good. I'm...
Top