Search results

I'll check that, too. Thanks

Thank you, Gordon. They were helpful. Now to go straighten it out.

Just saw this. I have two New Holland TC's. A 40 and a 45 hp. I find that I have used them for bucket work as much as anything and changing from forward to reverse with the HST is as fast as the thought. No stopping to change gears or moving a lever. Just think "go back" and that's what you...

I have just finished restoring a 1948 Farmall Super A. An IH sicklebar mower (I don't know the model, and don't know how to tell what it is) came with it needing a lot of repair. I have it all together and it goes back and forth like it should, however it immediately plugs up when trying to...

I, recently, rented a post hole auger designed to go on a skid steer. Worked fine on the front of the TC 40 although it turned slowly. Much better than the 3pt auger I own. I also have a bale grabber for round bales of hay. Works fine, might want a rear weight, won't lift the heaviest...

I just ran into the same codes. Baling hay and tractor XR4145 went into regen. Kept baling and it completed the regen (I think) then lost power and threw the S27 F08 codes. So the EGR fault seems reasonable. What to do about it??? Any ideas or info in your manual? Guess I should purchase...

Thanks. I'll do just that. Ed

I recently got a 350B which seems to be in excellent shape. Starts, Runs and everything works. Undercarriage seems tight and all is well. However, I would like to be sure that the rollers on the track are properly lubed. The book talks about the button grease fittings but when I tried to...

I have not found any tricks for mine. Just lots of patience and wishing I were double jointed in my arm/hand. You could take off the fender, but that is a lot of work, too.

About a year and a half ago, I stupidly flipped my TC40D upside down, backing up without looking. Fortunately, I escaped without serious injury but the tractor broke in half. I repaired it over the next couple of months, replacing the transmission gearcase and the hydro housing (bellhousing)...

So, my son has a B7500 with loader. He found a snowplow on CR for free so, of course, it has to be fitted to the tractor. He did a nice job of designing and building all of the necessary hangers, etc to attach it to the tractor and everything fits just as it should. The snowplow has hydraulic...

Didn't pay attention. Backed over a 4 foot bank and flipped the tractor over on me. Fortunately, I wasn't hurt and other than being sore for a week or so, no problems. However, the tractor is broken. Transmission case is broken and I can see a crack in the bell housing. I decided to fix it...

So I have an oil leak in the final drive on my tc40da. I have it all apart except for separating the top casting from the bottom one, where there is a roller bearing in between. There is no snap ring or anything else I can see keeping it together but I can't push the top casting out of the...

I have an old (1974) 3 cylinder 3550 backhoe. Is there an electronic ignition conversion available for it? Is it a big deal to install? Thanks, Eddie 48

Is there a tool that will allow me to relieve the pressure in the connectors so I can hook up my grapple without having to first loosen up the connector from the hose? I'm getting awful tired of having to have a couple of wrenches in hand every time I want to change the bucket to the grapple...

I just got to try out my new stump grapple from Unlimited Fabrication, LLC PO BOX 454 DENTON, NC 27239 I had about 15 stumps left in a field that used to be Christmas tree operation. I took the trees, mostly spruce, down last year, but didn't have any way to get the stumps out until...

I just finished resurecting a 200F manure spreader and then broke the already repaired once drive hub. This is the axle hub with 4 large lobes to actuate the arm that ratchets the bed chain. It also contains the two dogs which engage in the wheel hub. Does anyone know where I can find one?