Search results

I put washer fluid in mine. Way cheaper than beet juice. You must have some large tires to take 70 gal. each. Mine took about 37 gal. each.

I'm guessing he's talking about an EasyKleen hot water washer though he didn't mention what model. Those seem to be in the 3K and up price range.

Welcome to TBN....... Nice looking tractor. I watched the video and it seemed quite noisy inside requiring noise cancelling earmuffs. Nice feature having reversible seat. Looks like two videos combine. Beginning of vid shows manual blower chute rotating handle then at 32 seconds it isn't there...

Turn your rear blade around 180 deg. so it won't dig in.

That's why his has a lock where a key is required to remove it. If key isn't removed you can't access the device that lowers the spare.

It is the access point to you spare tire. Put your ignition key in and turn counter clockwise to remove the lock. Then you have to dig out your jack handle bars (mine were under the rear seat) and connect all the bars together and insert fully thru the hole. Then unwind to lower your spare wheel...

Eddie, I guess I'm lucky or on borrowed time. The battery is my LS tractor is still the original now 10 (almost 11 in 3 months) years old. The tractor is in the garage in the winter (5-6 months here) and I keep it on a trickle charger during winter. Spring, summer and fall its kept outside Hard...

I don't have a Yanmar. I watched the video and it looks to me to be full of brown water. Is there antifreeze coolant in there? I'd drain and flush the radiator, replace the thermostat, refill with 50/50 AF and replace the cap.

I currently have a 33 Chevy master 4 dr. sedan. It is an all steel body with updated drive train and a 57 Chevy sedan delivery also with updated drive train.

For just a couple times per year I'd install a trailer brake controller in your Chevy. Otherwise you're looking at buying a truck (new or used) that is rated to tow 10K or more. Preferably a 3/4T which has better suspension and brakes than a 1/2T.

I am also using FF 133. I recently had problems connecting to my server and showed an IDID xxxx error. I tried both FF and Chrome. Chrome worked but I couldn't check my email. I called my server who tried many options but was of no help in the end. The cure for me was to uninstall Firefox then...

If it is 5 degrees I suspect your fuel is gelling. Have you added any fuel treatment to prevent gelling? Check your fuel filter to see if it is cloudy. I use Power Service (white bottle) or something similar available at most auto parts and tractor supply stores. It says prevents gelling on the...

1) The problem here is NY drivers don't acknowledge the zipper merge. 2) Never seen a sign that say use both lanes until merge point. 3) Never seen a sign that says merge like a zipper. 4) Maybe its just this state but I'm assuming no one has ever heard of the zipper merge. I asked 10 of my...

If people merged into the thru lane when they saw the first merge single lane ahead sign then slowed down to 55 (its the law here) then everybody could go thru the construction zone at 55. There would be no waiting to merge at the last minute, no cutting in line, less stress and less horn...

I agree with rgr and I move to the through lane at the first lane closed ahead sign. If everyone did that there would be no bottleneck waiting at the last minute to cut in front. I bugs me a lot too when the ones in a hurry pass all those who have already merged then want to cut in front.

There are videos on YT on how electric trailer brakes work which will show you what is inside and how the magnet pulls an arm to engage the brakes. In your high humid environment its highly possible the arm may have rusted in the on position applying the shoe to the drum.

Try removing the wheel, then tap on the drum with a hammer. Sounds like the pivot arm with the magnet that swings has rusted in braked position. Also check your breakaway switch to make sure the pin hasn't pulled out. Also disconnect the trailer brake battery.

Bought mine at tractor supply store but you can get them at any tractor store, Runnings, Menards or online. Search for twisted clevis.

Yes, even when loader is attached you need to chain or strap the bucket. I bolted on D-rings to my front of tractor frame to hook chains thru. Also bought axle straps (pic) and a twisted clevis for tractor rear.

I bought 5/16" 20' chains, cut them in half and added new grab hooks to the cut off ends so I have 4 chains. 2 front / 2 back like ironman said. I use ratchet binders to secure. Make sure you chain your loader and any 3 pt. implements as well. Does your trailer have rub rails? If so you drop the...

I upgraded from a 7K tilt bed to a 14K full tilt bed PJ 10 years ago. My reason was similar with trailer being maxed out at times. Mainly I haul tractors, cars, and trucks. I do my own service and repairs. Trailer is used about 20 or more times per year. For me, I don't want to pay dealer...

Thanks for explaining that.

Your 785 has 4 cylinders, Isn't there a glow plug for each one? Please excuse my ignorance, I know nothing about the 785dtc

I agree with gstrom. I bought the 80 gallon Husky for my garage about 10 years ago. I upgraded from a 60 gallon that I had for almost 30 years. The tank bottom had rusted out and had pinhole leaks despite blowing it down once a week to get rid on moisture in the tank.

I have a Champion 9,000 lb 2 post. Been at least 10 years now. Only thing I'd do different would be to buy a 4 post drive on lift. As I've gotten older it gets harder to get on the floor to set the lift arms then get up

What is a Kioti 170H? I didn't find anything in tractordata. What size tire are you talking about?

I like your pic#1 having the tractor backed on the trailer. In pics 2&3 it appears like your truck will hit the bucket during a sharp turn. I prefer my trailer to be level (or close) when empty. IMO 6" is too high.

Getting that mileage is about right for your diesel truck. The longer the trip, the better the mileage. Short trips around town you'll be back down around 16-17. Be thankful its not a gas truck. I'm lucky to get 15 with my 6.0L (usually 13-13.5 avg.) but I don't take long trips. 90% of my trips...

I found the owners and parts manuals below but not the service manual https://lstractorusa.com/parts/ https://www.manualslib.com/products/Ls-Tractor-G3038-4070287.html https://sundownertractor.com/ls I ordered the factory parts and service manuals from the dealer when I bought my tractor. They...

Yes, specs, price and a your location would help a lot.

I keep 2 classic cars in garage year round except for nice weather driving. Truck and wife's car stay outside year round. Garage bay with lift stays open spring through fall for lift use. In winter the tractor goes in garage for easier starts.

Maybe just me but, I wouldn't want a 1500lb anything hanging over my head in the garage.

I've hauled many cars, trucks, and heavier tractors on my trailer without WD hitch and only notice about a 2" squat. Fortunately my trailer is long enough for me to move the load back and forth for better weight distribution. I mainly use the WD hitch when towing my camper which has lots of...

No, you don't have to modify the trailer to use a WD hitch. The only thing added to the trailer are what I call saddle brackets that clamp on. The chains attach to them for adjusting the hitch. Not sure what year your 2500 is but it squats way more than my 2016 with my 14K 22' tilt bed trailer...

Look up edge tamers online. The ones I see slide over the bucket edge and have a single bolt to tighten them down. No need to drill through bucket edge.

I have a cab for that reason plus for heat in winter and A/C in summer.

I have Spectrum also. I bought my own WiFi router (its a 4 antenna one) at wallyworld. Cost about $80. My previous WiFi was old and died. No need to call spectrum to set up router. It's easy to set up. Double check with Spectrum about your modem. I have their modem and TV multi-remote and don't...

Have you checked your cables (Pos and Neg). Try jump starting by connecting truck Pos to starter and Neg to frame. I've had the cable go bad as well as a poor ground to frame. I just replaced Pos and Neg cables on my street rod that did the same thing. Pos cable was bad inside but changed both...

I've pulled a few vehicles (tractors, trucks, cars) out of the mud over the years. I have used straps but found they would snap and come flying at me. Apparently they must have had a small cut or were frayed. Stopped using straps for that reason and have used chain ever since. Never had a chain...

Definitely get your trailer weighed. I have a PJ full tilt 22' 14K trailer that weighs close to 4K empty so I have roughly a 10K load rating. Not sure of your brand trailer or how its built so weight could be anywhere from 2-4K empty. Probably in the weight range Alexpops mentioned which would...

I have a 275 gallon tank I use for my tractor fuel. It has a 12V pump and I use a jump pack (I have a couple of them). I keep the jump pack plugged in my garage to keep it charged. I get #2 Home heating oil delivered when I need it.

Yes, As of this moment I'm the last to read and reply and when I click back button it does not go gray like I read it.

My home doesn't bring me back to unread New Posts. After the Boss fixed getting the Front Porch to show up in New Posts my back button automatically grayed out the read post. Not a big deal, its just another step I have to do (reload button) to mark it read. Maybe it's my browser (Firefox)...

The other day there was a fix to my question of posts from Front Page not showing when I click on New posts. That problem was fixed. The new problem is after the fix I would read a post then click the back button to return to other New posts and the post I just read was grayed out as shown in...

Same here

Every day I check in and click on New posts. It seems now that nothing posted in Front Porch show up to me when I click New posts. I have to leave New posts and go to Front porch to see them.

It cleared up and no longer shows the Custom Forum Widget. Thanks

At the top of my forums page is the following: [FS] Custom Forum Widget and scrolls thru items for sale. Is this something new that is supposed to be there

Just ate 2 of those big pack Oatmeal Cremes then checked in here and see the ad.

Bob Newhart, deadpan comedy legend, dies at 94

Have you checked your ground cable connection to the frame and hot cable to starter. After checking fuses, that's where I'd look.

Welcome to TBN................

Shannen Doherty died July 13 age 53

Can't see much from the pic. She'd need to pop out of the screen and sit on my lap for me to make a better assessment.

Ask if any service has been done yet such as fluids and filters. If not it is due. Seems like very low hours, 45 hours in 5 yrs. is super low. I have the older 3000 series cab model and I put under 40 hours per year on it. Mine is 10 years old now. LS3135 has an LS engine, Massey 1735M has the...

Two of my cars still have that switch

Here's mine

I have Win 11 on my laptop. I save a pic on my desktop (or other folder). Open the pic, right click, and have a menu pop up where I can easily resize the pic.

I had a similar problem with my LS. Had to remove the cover over the parking brake and bend the bracket holding the safety switch to make a better connection. Yours may be similar.

Another vote for WW fluid. I filled mine with WW fluid 10 years ago right after purchase. No problems so far. Got mine on sale at a cheap price too. The look on the sales guys face was priceless when I asked for 80 gallons.

I just watched a video to use a portable water deionizer that removes minerals in the water along with special low Ph car wash soap. Then rinse and blow dry the remainder of the water off. Deionizer price is too much for me to spend so I guess I'll keep doing what I have been. Another video says...

Is that ceramic wash and coat just sprayed on? The product I've seen is applied by hand as you would a good wax then residue is wiped off with microfiber towel. I tried a similar product using my foam cannon but then hosed off and still got spots. I think the only way to achieve success is to...

I have the same hard water problem. Also have a water softener but still get water spots. I have two classic cars and after washing and drying I find I still have to go over the entire car with Maguires quick detailer (or your brand of choice) with microfiber towel to buff out the water spots...

Looks like Robert Conrad from Wild Wild West TV show

I had a similar problem with a Cub Cadet. I had 12V going to the PTO clutch when the switch was activated but it wouldn't engage. There is only 2 wires, one hot from the switch and 1 ground. Turns out it had no ground. I used a jumper wire with alligator clips to test and the clutch engaged...

That's just the handle so you can pick it up to turn it around.

Most any auto parts store sells the rocker switch and rolls of wire you need.

Is there a reason why you can't power the new pump off the same seven terminal plug? Just get the plug end and wire it to the new sprayer. Or, add wire and battery clips as mentioned temporarily.

What tractor are you looking at?

Tractordata.com usually lists approx. years based on model and vin#s

I've never sprayed with it but I have brushed on POR-15 on many items (trailer frame included) that has held up well for many years. It is expensive though. I have also sprayed rustoleum but hasn't lasted as long as POR.

I had that happen for a part ordered on Ebay a few years ago. Like you, the part ordered and part rec'd were different numbers. I contacted Ebay and said seller sent wrong part. Ebay must have contacted seller. They said no problem and would take back and send correct part I ordered. Correct...

I have a 14K PJ model TF 22'. It's not the deck over which you need. Mine is also power up/ power down. You should go and see one. On mine, the deck is 22' then the steel tail adds another 20" so it's almost 24'. This is my second full tilt and I love not having to mess with ramps. I also added...

Maybe that's the extension cord for that electric (Rivian) truck

Yes, I prefer the tilt bed. I've had many conventional trailers with ramps in the past but as I got older ramps were no longer fun to use and seemed to get heavier too, plus with ramps many smaller low clearance cars have a hard time getting over the hump. My current trailer has a 22' wood...

I wouldn't worry about the 900 lb tongue weight. You can always use a weight distribution hitch. Also, your 4700 lb. tractor weight plus trailer weight (3500-4000 lb.) will be just under your truck tow rating of 9K. I had a 20' full tilt bed and found it to be too short at times. Sold it and...

I'm not sure on the machine. The OP hasn't replied back to confirm the model but I couldn't find a 3110 by LS. It is possible it could be a foreign model. If so then I'd be leery of buying it for parts availability.

Did you mean an LS S3010. If so, that has a Mitsubishi 4 cyl diesel Pre emissions. With only 300 hrs. I think it would be a desirable tractor. Ask the seller if he has kept any service records. LS has been building tractors for many years. Mainly for other companies before starting their own...

Welcome to TBN......................

Let's just hurry up a little and get MY car done. Local car cruises start in 5 weeks here and I want to pick it up.

I ran two lines from a rear remote to the front to operate the power angle of my quick attach snow plow. I bought the ready made hoses and couplers from a local tractor supply store. Just fished them under the tractor to the front and zip tied in place where they won't get damaged.

Red fuel is off road fuel. It is perfectly safe to use in diesel tractors but not for highway use. Red diesel is also used in home heating. That fuel pump should be marked for off road or home heating oil. If that pump is located where trucks fuel up they may be in violation.

Just do a search for the part number and see who sells it in your area. Most places here in US will ship to Canada.

Messick's has it for around $16

My 50th was 4 years ago. I think the last reunion we had was the 15th, none since.

I use a Dell laptop, Firefox, Adblock plus and Adblock ultimate. Knock on wood I don't see any ads. I hope it stays that way for me.

My 22' PJ tilt deck has also been outside 24/7 since new in 2014. Deck is PT pine (2x6) from factory. It does turn green from pollen which makes it slippery when wet but my pressure washer takes it off easily. I also coat mine with diesel and oil mix every couple years.

What kind of tongue weight does the trailer have? What vehicle are you towing with? Have you checked your trailer hitch label . They recommend using a weight distribution hitch at certain weights. Maybe your truck rear suspension needs improving. My tilt bed PJ empty tongue weight is 1195 lb...

I have a 2 post 9000lb lift made by Challenger in USA. My buddy has a 4 post lift (don't know brand). Both have pros/cons. I do like buddy's 4 post because it isn't bolted down and he has rollers he can put on each corner and move it if needed. My garage isn't large enough to allow moving the...

The cab is nice in winter (at least it is why I bought mine) to have heat while plowing snow. Not sure how much snow you get in your location. Also nice to have AC on those hot summer days. My current 2014 LS XR3037HC is the first cabbed tractor I've had over 40 plus years of owning tractors...

Number 5 for me also

If yours is the original, no telling when the seal would go. Buy the new one and install.

I have AT&T in central NY. No outage here.

It's a 49. Was originally a fire tanker truck. I made the flatbed for it. and replaced the original babbit bearing motor with a 235Cu In out of a 55 car.

I have a 2016 Chevy 2500HD crew cab, 6.0, 4x4. Bought new when I retired. Use it for general running around, towing 14K tilt bed trailer, 14K dump trailer, 30' camper. MPG sucks but it was the price I had to pay to haul the trailers which are all out of my previous Chevy 1/2T range.

Is that your 55 Chevy, Mustang and Nova under the carport?

Is the plow angling function manual (such as manually moving a pin) or is it angled by hydraulics? Perhaps you are using the curl function to angle the blade. If hydraulic you can install a cushion valve which will allow the blade to turn if a solid object is hit. I have one on my tractors...

Julie Newmar is 90? I guess I'm old too

But that truck has the emissions crap that you didn't want

I have a PJ model TF 22' full tilt 14K bought new in 2007. It replaced a 20' 7K '. Best trailer I've owned.

I still use it on sudoku puzzles that I do in pen.

Member Title - Number of Posts New Member - 0 Member - 25 Bronze Member - 50 Silver Member - 100 Gold Member - 250 Platinum Member - 500 (also gives you access to the private Front Porch community forum) Veteran Member - 1000 Elite Member - 2500 Super Member - 5000 Super Star Member - 10000 Epic...

I think it was the lennon sisters.

Looks like it goes on the floor mounted dimmer switch to match the throttle pedal.

I guess it depends on how bad you want the land for your piece of mind to not have neighbors or a small development built next to you. 10 years ago I wanted to buy 4 acres next to me. Property in my rural area at the time was selling for 3-5K per acre. However, the catch, on this property only...

Sounds like the dealer may have the exact truck (an 07 3500) that you are looking for. Hope its in as good a condition as the 09.

You could remove the lift pins, then weld on some 1/4" flat steel to move the mounting tabs on the outside of the box to bolt the pins to.

I'll guess $20,995

Not necessarily. My previous tractor ate glow plugs every 2 years. I'd have 2 plugs shorted to ground and 1 that worked and never blew a fuse. Turns out it was a mfg. engineering defect. After replacing plugs 3 times they came out with an upgrade kit of 3 different voltage plugs and a new timer...

How did you test the glow plugs? Did you remove the buss bar connecting them together then check each plug individually? If the glow plug light works normal when buss bar is disconnected but not when hooked up it seems to me you have a plug that is shorted to ground.

Is it possible your fuel is gelling? Temps have been pretty low lately.

Just had it happen to me too

My tractor is in a semi heated garage (about 40-45 deg.F). I too use PS year round. Adding some to your tank before taking it out for a couple hours I think the vibration of the tractor will mix it just fine. At -15 F I would use it.

Welcome to TBN..... Not familiar with your tractor but a similar thing happened to me on an HST tractor I had. While getting on the tractor I accidentally bumped the range selector into neutral and it wouldn't move.

Not sure of your location and whether ambient temps may be too cold causing fuel gelling. That is one reason that would for your symptoms.

I think manufacturers de-rate those trailers to avoid braking requirements. Most states require brakes on trailers over 3000#.

I have heated gloves for occasional motorcycle riding but they are not thin. Below is a link I found for thin heated gloves. Don't know if they would work for you. https://bestwintergloves.com/thin-heated-gloves/

I think you answered your own question. If you can bog down a 44HP tractor you would certainly bog down a 25HP UTV. The problem is IMO any tractor, UTV, RTV Etc. with a blower can be bogged down. Speed and snow density makes the difference.

Your Cub is like my Craftsman 28HP rider, key switch has the PTO in reverse position. I had an older Cub without the reverse cut off safety.

Again, I don't have a 425 so don't know if the PTO switch stays in that position once activated or if you have to lift it each time you reverse. I believe that since its a safety feature that once you go forward the switch goes back down. PITA but that's how Mfgs. build stuff. They incorporated...

Check pages 38-39 to operate PTO in reverse https://manualmachine.com/johndeere/425/4536257-operators-manual/

Check below on page 38-39 to keep PTO engaged in reverse. https://manualmachine.com/johndeere/425/4536257-operators-manual/

Sorry but no. I don't even know how many contacts are on mine just that the key has 4 positions. Do you have the owners manual. If so it should describe how to keep PTO engaged in reverse.

Welcome to TBN.................. Be careful buying a JD tlb110. Many (not all) had problems with cracking around the bellhousing. Check it good for any welding repairs. An excavator will work way better and faster for digging foundations than a tlb. What are your plans for a tractor. IMO I...

My keyswitch has 4 positions. Off-ON2-ON1-Start. After starting the key goes to ON1 automatically. In that position the PTO shuts off in reverse. If I put it in ON2 the PTO stays running in reverse. I only mow with mine and I want my mower running fwd and reverse.

Does your keyswitch have an override position? I don't have a 425 but my lawn tractor has a switch position that keeps the PTO on when backing up And Welcome to TBN

Know you are old when you have more Doctors office numbers in your phone than friends. And yes I take baby aspirin (among many other pills) daily. Hard to believe 10 years ago I took no pills and only had 1 doctor.

If I was in the market for a larger tractor I'd be all over that Massey. Good find paulsharvey

Its 150 miles SW from me. A little too far for me to drive in winter. We just got a foot of snow last night. I'd go if it was a lot closer

Where is it in upstate NY?

He did post it. I looked but with over 500 replies I couldn't find it. Found it. Couldn't connect using jstpssng's link https://www.tractorbynet.com/forums/threads/well%E2%80%A6-that-was-stupid%E2%80%A6.473550/page-2#post-6720998 Post #40 in the Well...that was stupid... thread

I had a 2615 HST which I believe is a previous model of your 2516. I towed a 6x12 single axle for many a job but needed a larger trailer to haul the tractor from time to time. I bought a 84" x 20' 2 axle tilt bed car trailer. The trailer hauled the tractor fine and when needed the tractor would...

Welcome to TBN neighbor.

Was that a typo in the last sentence or you've had enough and ready to quit.

Fortunately I only need reading glasses so I bought several pair and have a set in each vehicle (5) plus (2) pair for in house computer work and 1 pair in garage.

I built a steel frame inside the barrel using scrap rectangle tubing, a piece of 1" bar stock and came out the front for the top link. I also added more steel out the back and added a hook for a chain. Sorry for the blurry pics. Its cold out here and I must have been shaking a little. Don't pay...

Have you thought about a plastic 55 gallon barrel? I built mine fairly easy and filled 3/4 of the way it weighs 927#. I'm sure if I had filled it with concrete it would about 1K or more. I also obtained an old records safe for free when a Dr. office moved and didn't want to pay to move it. It is...

Welcome to the forum. I'm 20 miles north of Syracuse.

I had a 16' dump trailer and did haul my tractor occasionally. Yes it did have D-rings (6). Not sure if all dump trailers have them. Mine was made by Cross Country Trailers.

I have the same model but it's a 2014 with only 400 hrs. I would think yours would be worth about $22-25K. That's what I would ask for mine. Prices have gone up since you and I purchased ours.

A local truck dealer (about 20 miles from me) was just arrested for disabling emission control systems on 244 used diesel trucks he sold over a 4 year period. He faces 5 years in jail and a $250K fine if found guilty in court. The EPA is cracking down.

Have you tried using a jumper cable directly from the battery to the starter terminal to see if it cranks over?

You should have no problem moving your trailers around. I move my camper Around 10K), enclosed (7K), and dump trailer(5K) using a 3 pt receiver hitch I built.

I filled my rears with windshield washer fluid. Got it at a Runnings store (like a tractor supply store) when they had it on sale. It was cheaper than RV AF or Rimguard.

Confirm the price is tractor with implements. For the price I'd buy it, keep the implements and sell the tractor then look for another 4WD tractor with loader.

I was going to suggest PJ but you say no dealer close by. I have a 14K PJ model TF full tilt bed. Bought it new in 2014 an paint has held up great. Very nicely built IMO. I haven't kept up with other brands since I got mine. I drove 50 miles each way to get mine. If your nearest dealer is in...

I'll try to answer your questions to the best of my knowledge. 1) In my state the vehicle is what is insured. If my vehicle is in a wreck I'd call my insurance and they would take care of repairing or totaling the car. Same if I loaned my car to someone else and they were involved in a wreck. My...

Congrats on your boys decision. I was there (Lackland) back in 1970. I'm sure a few things have changed since then. Seems like he has good morals and ethics and you should be proud.

Like some others I too run an ad blocker and never see any pop ups or ads. So simple to add a blocker to your browser program.

I sure that somewhere there is a guy with an old restored M/C that would want that plate. Maybe an ad placed on CL or FB might get some interest. Can't see it would be worth much but I'm cheap and wouldn't pay a lot for it.

That appears to be an old PA motorcycle plate last registered in 69 based on the sticker.

It depends on condition. Some states will not let you restore or repaint the plates. A lot of classic car owners look for them at flea markets or online to put on their cars. In good to excellent condition they sell for $50-150 a set. Beat up old plates have little value. I have two classic cars...

I'm sure at one time the dist. was installed correctly before the gear got chewed up. Before you install the new dist you will have to get the timing mark on the crankshaft damper pulley set to top dead center then install the dist. so it will be lined up to fire on number one cylinder. Once...

my first name. The 2615 comes from 2 tractors I used to own, a MF2615 and a Mahindra 2615.

Most tractor supply stores carry universal lift arms. Just take yours in and measure the length.

Yes, that distributor shaft must turn when the engine is cranking. If not, you won't get spark to each plug. I cannot see how it ran at all in your first post if the shaft doesn't turn. Seems like something is broken on the bottom of the distributor shaft. I had an MF135 many years ago but never...

Does your tractor ECM mount on top of the battery? If so it may be the same as mine and height measurement may be critical. The stock Battery is 80AH, part #40007051, MF TRG740 as of 11-30-2006. If you need to replace I'd just pull it out, take to battery or auto parts store and match it up...

Thanks to all who served past and present

I have a 2014 of the same model. Mine regens about every 4-5 hours which is the norm for this model. Next time yours goes into regen try bumping the throttle up to 24-2500 RPM which will make it run at a higher temp. Another thing that may affect regen is the quality of the fuel. I also run an...

I used Anderson power connector plugs (A bit overkill but it was all I had at the time). Mounted one on tractor direct to battery and other on pump wiring and simply plug in when I need to fill up. You could do the same on your tractor and ATV.

How many amps did the tech up the fuse to. Maybe the wiring was not capable of handling the extra amps of the higher current fuse and has burned up.

I checked the site below and it shows the front seal as a different part # than you list. Is that the seal you need? https://lstractorusa.com/parts/ part# 40334121

I bought my LS XR3037HC (Cab with 2 pedal hydro) new in 2014. My model is no longer made and I haven't kept up with newer models. Mine is 36HP and loader can lift just over 2200#. 9 years old and still going strong with routine maintenance. My buddy bought his XR4140HC w/ Backhoe a few years ago...

Earlier today the site wouldn't load. Apparently it was down for a repair or upgrade since it is back online now. It has happened a few times to me also. I just wait an hour or so and try again. Usually the Admin's place a post if they know the site is going to be down for an upgrade.

Welcome to TBN.. 0n Tractordata site it shows you have the choice to use R1 (Ag) or R4 (Industrial). However, You will also need to change the wheels as well. https://www.tractordata.com/farm-tractors/001/8/3/1838-kubota-l5740-dimensions.html

Yes, the tilt beds do add a premium to the cost. But, I don't have to lift or raise heavy ramps anymore. My back appreciates that. The extra length lets me adjust the load for more or less tongue weight. Its not usually a problem as the rear of my 2500 barely drops an inch or two with loaded...

Were you sitting on the seat when you released the brake after starting? My mower will only stay running if the brake is on or if I'm sitting on the seat. Same with engaging mower deck, only will engage and keep running if on the seat. I'd suspect you have a bad seat switch. Also check your...

I upgraded from a 20' 7K tilt bed to a 22' 14K tilt bed trailer 9 years ago. I went with a PJ model TF (full tilt). Its listed as a 22' but actual deck length incl. tail is 23'9". Gives me plenty of room to adjust a load. Mainly use for hauling vehicles, implements, and tractors. I like that the...

Put a Sony in mine https://www.tractorbynet.com/forums/threads/radio.435525/#post-5951721 Wiring info https://www.tractorbynet.com/forums/threads/radio-wiring-for-xr3037hc-cab-models.334920/

In the middle, between the 2 cylinders is a safety lock. It must be released to let it come down. The directions should show you how to release the safety lock. You may have to raise it a bit more to release the latch.

Welcome to TBN........... Have you checked the control valve below your seat? Usually there is a knob the controls how fast the 3 pt will drop. If the knob is fully clockwise the valve is closed and won't let the 3pt. go down.

It tilts about 11 degrees before the tail touches the ground so not much would dump off it.

I wasn't sure of the metal thickness on top of the bucket so I added a piece of 3/16" angle all the way across and welded my hooks to that.

I have a PJ 14K tilt bed model TF 22' (actual just under 24' including tail). I added a winch and made D-rings that drop into the stake pockets. The axles are placed back further than most other brands so its not real long behind them. Weighs just under 4K. Tow with a Chevy 2500HD crew cab 4x4...

It's working for me. Has been since Ibrahim fixed it this morning.

Can't mark forums read today. Anyone else having this problem?

You can run hoses from the rear remotes to the front. I did it and use them to operate a hydraulic thumb on my forks and to angle a snow plow in winter. Bought hose and fittings at tractor supply. Ran them under the tractor and zip tied in place. I posted a thread listing all materials used but...

Sorry, no photos but when I raised my roof I only lifted it high enough for the support rod to hold it. Was less than a 45 degree angle which still gave plenty of room to access anything in there. I think the front of the roof was up maybe 2' so pretty sure 10'6" will be high enough. If I recall...

The roof is hinged at the rear. one nut on each side and two nuts in front and the roof lifts up. There is a rod inside the roof to support it when lifted.

When I was looking for a trailer back in 2012-14 I went to several auctions that included different trailers. I was very disappointed to find trailer plugs cut off, tires shot, non functional lighting, brakes, decking that needed replacing etc. I hoped they would go for cheap knowing the amount...

The ground cable may be corroded internally where you cant see it. Try connecting a jumper cable from battery to frame and try to start again. Could also be the positive cable with internal breakdown.

I get emails about my amazon, email and paypal accounts being frozen. I never open them. I suspect it is a scam and just delete them. I do log into each of those secured accounts (but not from the emails someone sent) to check if there are any notifications but there never is any problem.

Here's mine. At the top of this page click on search then type in grill guard and click search. There are many threads that will come up for others guards.

When you agreed to the purchase and made your down payment did your receipt show the full agreed price. If so you should be able to get your tractor at that price. They can't add more to an agreed contract price. Contact an attorney.

If your Kubota has the standard quick attach bucket you can buy a larger bucket (wider and taller). The problem may be that your loader hydraulics may not be able to lift it depending on the weight. Quickattach is one company that sells larger buckets. I'm sure there are many others too.

OK Thanks. I see that groan now comes up clicking on new posts again.

I check new posts daily and prior to 3-4 days ago the Groan Part Quatre did show up. I would then copy or download (save) the memes. I never had to go to front porch to find the groan thread new memes before. Was the Groan thread recently moved to front porch?

I've noticed that in the past few days that anything posted in Front Porch don't show up when I click on new posts. I have to manually switch to FP to see newest posts. Did something change? For example: I used to click on new posts to see if anything new was posted in Groan part quatre. Past...

In the first post you stated diesel got into the oil. Has that contaminated oil and filter been changed yet? I'm not sure if that would make a difference on running.

I just went to the front porch and your post is still there

Fuel filter been replaced lately. If so, then have you checked your glow plugs to ensure they are working. Sounds like your battery is good if it cranks over easily just not enough heat in the cylinders to fire.

Yes, almost daily use for 40 plus years.

Here's a few of mine. CRKT, Small Craftsman, Small Case, Camillus electrician, and smaller Camillus. The Camillus electrician I bought from Camillus Cutlery in 1983, the small Camillus I found in my Dads toolbox back in 1990, Craftsman I bought at Sears in the 70's and the Case also in the 70's...

No white strip here. All seems normal. Using a laptop, Win 11, Firefox with adblock.

Here's the one I bought that does plug into the port. See this thread too. The plug is unkeyed. https://www.tractorbynet.com/forums/threads/diagnostic-code-reader.390565/ https://obd2allinone.com/products/catobd2.asp

So the GCVWR of truck and trailer is 29,700. Its been many years since I took math in school but I think 29,700 is greater than 26,000. Many states go by GCVWR not actual weight and would require a CDL to operate your truck/trailer.

So your 1 ton has a GVWR of less than 8K?

The chain & padlock will do for now. Unbolt the latch & lock assy. from inside and take to a locksmith. They can change the tumblers and make you a couple keys then bolt it back in.

I'm 70 and had both eyes done about 3 years ago. Had distance vision corrected. (I wore glasses for almost 60 years to see distance). Now only need reading glasses which are cheap. Just had my annual checkup about 3 weeks ago. Vision is still 20/20 since surgery. No problems driving day or...

I added these LED strobes to my tractor. Local highway dept. saw them flashing over 1/4 mile away as they were coming up the road.