Search results

I just purchased an Enorossi BF210H sickle bar mower. I hooked up the hydraulic line and nothing happens. My hook up is as follows: I removed the two quick connects from my rear remote that operates my grapple. I connected the sickle bar quick connect to one of the rear remote ports and left...

I'm trying to remove the PTO drive shaft from my PHD gearbox. I have removed the shear bolt, but the yoke will not slide off. It will rotate on the shaft however. I suspect I need to remove a small roll pin visible in the attached photos, but do not know how to get it out. Any advice?

At least I think it was a squirrel since I have so many around. I have about 15 places around the base of my steel building where the critter was trying to get out. While I was using my tractor Saturday I left the door open. Afterwards I put the tractor up and closed the door. This morning I...

I bought a used Olathe 3 pt debris blower. The drive chain is broken and I need to put it back together using a connecting link. The pictures of connecting links on the web doesn't seem to include the rollers. Can you buy them or am I looking at getting a new chain?

Does anyone have suggestions on a good quality, not super expensive, 20x70 binoculars? I see them anywhere from $50 and up. I know in a lot of cases you pay extra for a particular name brand which may or may not mean anything.

The manual for my Kubota KX91-2 specifies ISO 46 (in my temperature range). Kubota oil at the dealer is double the price of ISO 46 at Tractor Supply. Is the TSC oil the same? In other words is ISO 46 essentially the same in all brands or does that simply mean the viscosity is the same, but...

I have an opportunity to buy a mini ex at a good price. The owner says one track will jump off in tight situations even though the tension bar has been maxed out and the track shortened. I know nothing about excavators. Is this an expensive fix?

I have an opportunity to obtain the BH in these pictures (not able to get the tractor). How difficult will it be to adapt it to a 2008 JD 4320?

I have a Bush Hog 286 that I run off my JD 48 hp tractor. I also have a NH 29D with 25 hp at the PTO. I know the ratings, but wondered if I'm taking a terrible chance of damaging my NH by using the BH286 off it. The work will be light. The...

I have a Stihl model HS 80 hedge trimmer that will not rev up. The last time I used it about a month ago it ran fine. It cranks very easy, but when I pull the throttle it dies before it even gets up to 1/3 speed. I have changed the plug, cleaned the air filter and changed the fuel pick-up...

I need an enclosed trailer to move from GA to NC. I plan to "transition" and will make several trips. I have an 8.5 x 24 enclosed car hauler trailer, but it's just a little too big when fully loaded for my tow vehicle. My tow vehicle is a 2000 Ford F-250, 2WD, 7.3 diesel. I have a flatbed...

I have an uninhabitable cabin on my property that is far from critter proof. Squirrels love to come in and really make a mess. Does anyone know if a radio going 24/7 will keep them from coming in? Other ideas? It will be a while before I can stop up all the holes.

I recently purchased 76 acres of land, 50 of which are under a forestry management program. Can "crop" insurance be purchased against wind, fire, ice, disease, etc. damage to the existing and future timber? If so, how does such a policy work, and what is the approximate cost? I've found a lot...

I would like to move the referenced utility building on my trailer about 300 miles. All but the last 30 miles are interstate. My trailer is more than adequate, but I am wondering if I should just dismantle it into sections and put it back together, or try to move it intact. That is a long way...

I have a 24' enclosed car hauler trailer with a ramp door. The ramp door has three hinges at the bottom, left, center and right. The right hinge has been bent from I guess too much load (I bought it used), and I cannot figure out how to straighten it. The door will not close tight on the...

The reason I ask is because I saw an FEL bucket on Craiglist described as 60" JD QA bucket. Is it safe to assume it would fit my 400CX loader? Mine has the 73" HD bucket, but it would be nice to have two...one with a tooth bar.

Is there a web link, or photos showing all three rear remotes and power beyond for the 4x20 series tractors? I'm just interested in seeing what this looks like all decked out.

I'm attempting to get a price quote for a 4320 tractor with all the possible hydraulic combinations. The problem is that the salesman at the dealership working with me either knows less than me or is determined to sell me a tractor on the lot. I'm not in a hurry at all and would prefer to...

I wanted to add two rear remotes to my TC29D. I called NH and the price for kit 1 and 2 added together total $1,500. That seems outrageous to me. The parts guy did ask "do you get a discount?. Anyone know what a typical discount is for those who get one? I may have to get someone to buy...