Search results

I have a B2150 hydrostat and a strange leak just developed. I’m starting to troubleshoot and will start pulling some covers off but checking in to see if anyone has seen this before. Fluid is actually pushing up the steering shaft from below the dashboard and spilling out and down the metal...

New to me B2150. Going thru everything as a few things were neglected by previous owner. Oil pressure light doesn’t come on with key. Pulled dash hoping it was bulb, but bulb confirmed good. Sending unit or something else? Are they a generic item or Kubota only part? Appreciate any thoughts!

My B2150 gear tractor just started “banging” when driving forward like once a second when advancing slowly. It doesn’t make noise in reverse. Doesn’t matter if the clutch is pushed in. It does it all 3 ranges and with our without 4wd engaged. It sounds like it is coming from the tunnel...

Got a new front end issue, leaking at the bottom where the axle and knuckle meet. Seal, o ring, etc? Hoping someone who has been there before can weigh in. What痴 involved in tearing it down to repair? Thanks

All of a sudden my loader valve (Kubota) doesn't want to move fully in one direction - to raise the bucket. The other way is fine and the other valve for bucket curl is operating fine. any ideas or suggestions appreciated!

l'm slowly working towards putting an old truck plow on in place of the bucket on the front loader. It can be angled using the hydraulic cylinders or manually if I pulled them off. I'm on the fence about tilt, talk me into or out of it... I currently have another light blade clamp mounted to...

I bought a used implement, the PTO shaft must have rubbed on something because the plastic tube is abraded completely thru. I have it taken apart, hoping I can just buy a new tube and put it back together, but not finding lots of Bondioli and Pavesi parts after a brief search. Any sources out...

The local buses weren't running this week until they mixed ULSD Kero in with the diesel. See Cold Freezes Bus Fuel—Closes Schools - 13WHAM.com

Has anyone upgraded their machine? I originally thought I could try and squeeze in a small aftermarket alternator, but the spacing is tight and I think I might be better off with a stock set-up. I checked with the Tractorsmart folks, the whole goods part kit B9322 isn't available anymore. So...

Want to go higher tech on the old garage door, but don't know much about the so-called "commercial grade" garage door openers, advice is welcome! Thanks,

I recently started having trouble with my JD316 flipping the v belt over on the drive belt that goes from the engine to the mower deck. Replaced the belt, doesn't seem to be any bind in the deck itself, looking for any ideas/experience. This is the older style 316 (circa 1982?), Kohler motor...

Anyone got any real up-close experience. They are planned to go up on the farm next to me and they want every kilowatt so these will be the biggest ones ever in NY ( 399 feet tall). I am all for green power, just concerned over the noise level. Town has a new law with a 50dBA level at the...

Mike was kind enough to illustrate how his canopy attached so I could make own of my own. I'm slow and this proves it cause I'm still not done, but progress is being made. If I could just get used to steering around that board that is holding the front end up, I'd be closer. I hope I can find...

I'm on the lookout for a Model A car transmission for a stepdown project on my Oliver, anyone have one laying around that they want to part with for a fair price? Happy Holidays!

It is almost tire chain season I got a new set of 2 link chains and am thinking about some spacers to keep them off my fender when they loosen up. I have a blueprint for the spacer that I got somewhere, but still have one question for anyone that has put them on. I have 4 bolts on each wheel...

I haven't keep up to date, work is a little overwhelming lately. Has the pace slowed down enough to get a decent price on the RTVs? I will probably look at the recreation model and install the aftermarket hydraulic bed lift to meet my needs. thanks for any input. Marty

I have the pleasure of using an Oliver OC3 dozer once I get it running. It has been sitting for a couple years and has no spark , but the mag was rebuilt professionally not long before it sat. I've been researching Wicos and know that the points tend to corrode and also that the impulse dogs...

I see these as an option - anybody got info on them, or actually have them, doesn't seem to be alot of info about them on the website. I'm thinking about a worksite model, wondering if these are a good addition. Marty

I keep forgetting to ask this question. I was mowing last summer with the flail which vibrates a bit - yeah I know I need to fix a couple knives . Anyway, I happened to see my key laying down by my feet. It had fallen out. Further checking, it is no problem to remove the key in either the...

Well I still have a ways to go collecting parts, but I acquired a valve assembly for the backhoe I intend to build. Ebay is more dangerous to surf than this board. It is a seven spool set-up, 2 joysticks, 2 single valves and it also has an electric 4 way valve. I am looking at building a...

Just planning some electrical wiring layout for my canopy ... would like to consider some sort of enclosure later... I want to put some sort of console in and need to know what to leave room for. Do most cab have both front and rear wipers available? Are the wipers continuous or do you hit a...

I am interested in making my own canopy from diamond plate aluminium. I borrowed a picture from Pineridge showing some canopy supports and that gives me the basic idea but I am still being lazy. Can anyone measure the height width and thickness of the side plates and the dimensions and wall...

Might be old news to some of you, but I ran across a safe and easy way to remove rust from parts using electrolysis. Lots of websites on Google, one is rust removal Supposed to be great for stubborn old bolts too.

I'm thinking that someone must have done this already and could give me some pointers? I have a 1992 B2150DT with a factory loader. I got an email from TractorSmart when I asked about a rear hydraulic kit that suggests the loader has taken the only available hydraulic outlet on the tractor...