Search results

I have an Exmark zero-turn with Kawasaki FX801V engine. Brought it in the garage last fall, all was running perfectly. This winter I changed the oil and filter, fuel filter and the rocker cover gaskets because they were leaking a bit. While I had those off I figured I would check/set the valve...

Doing the 400 hr hydraulic fluid and filter change, found this between filter base and hyd suction filter. Someone at factory got a little sloppy with the RTV? Also found this at rear of front transmission case, pretty common I suppose. Needle nose pliers, grab and pull. Just thought I’d...

Working on replacing gear case seal, have removed snap ring above bottom bevel gear. Doesnt seem to want to come off, have tried rubber mallet and small hammer on block of wood. Anything else to remove or just go to bigger hammer? On a B3200.

On my truck, not tractor. 2016 F-350 DRW. Attached to rear axle, appears to be a vent. There’s a clip that looks like it should attach somewhere, and a fitting on the end. Anyone?

Looking for a simple GPS app for smartphone or tablet that allows you to set a swath, then records your path around the field so you can keep track of where you’ve been. Suggestions?

Considering looking at one of these, 9600 hrs, looks clean and cared for. Anything in particular to look for that should be a deal breaker?

Noticed this today, looks like it has been leaking for a while. Seems to be leaking at the joint here (arrow) Is this a DIY fix? I’m fairly handy.

.....

For those of you who use these regularly to move rounds or large squares, how important is having some rollback angle? The way my loader works, the attachment point is pretty much vertical at full rollback when the bucket is on the ground.

Anyone know what thread size is for these locations on ROPS on B3200?

I may be going to look at a used Vicon pendulum-type spreader to purchase. Never seen one up close, anything in particular I need to look at?

Got the tractor out tonight to do some mowing. I kept getting the feeling that something wasn't quite right. Felt like something was dragging, or had a low tire. I noticed that it didn't quite 'coast' as smoothly as it normally does, just felt heavy. The pedals both seem to return fully when...

Trash day, one of my cans has big crack. These are Toter cans, heavy PE not cheapies. Harbor Freight sells a welder for under $50, thought it might be fun to play around with. Anyone try anything like this?

Anyone have any experience with this quick hitch? Category 1 Quick Hitch 14116 by Speeco Inc for $119.99 in Misc. Equipment - 3 Point Utility Equipment - 3 Point Equipment & Accessories - Agriculture : Rural King After a neighbor recommended it, wife brought one home. Put it on the...

saw an ad on CL, says the composition is 5-3-2. Says 'very high source of nitrogen'. I read that composition as 5% nitrogen, 3% phosphorous and 2% potassium. So I'd need to apply a ton/acre to get 100#/acre N. Anyone know the cost?

Hi, built new horse barn last year, now we are wanting to get water/electric out there. About 150' from house to barn. I am thinking about renting trencher and putting water line, direct bury electric and conduit for video/cat5 in the same trench. Planning on digging down 4' and putting water...

'16 F-350. As far as what position to put the front hubs in. What's the difference? might seem a stupid question to some, but the owners manual does a poor job of explaining :reading: :confused: . Primarily on-road hauling or towing with occasional trips across soft/muddy fields. So it's in 4x2...

On my Kubota loader, where the lines transition from rigid lines to the couplers, what sizes of wrenches do I need? I think the bigger of the two is 22mm, what's the other? Bigger wrenches like this are pricey, not looking to buy a whole set right now.

I have B3200 that I want to use to keep about 15 acres of horse pasture mowed. Want to keep it cut no shorter than 6", and no taller than a foot or so. Any big advantage of one type of mower over the other? How big of a mower can I go? Land is very flat. Manual says 72" on finish and 5' on...

Considering buying ETA-60XDBB-30-70 box blade to use with my B3200. Web site says blade weighs 455#. I have borrowed a friends 60" King Kutter blade before and it worked well. Thoughts? Opinions? thanks

Wife went to start tractor this afternoon, no go. Checked battery, 11.8v or something. Jumped it to start, 10.something across terminals. So the ignition/headlights are pulling it even lower while running, obviously not getting anything from the charging circuit. New battery as of last...

I need to replace all four tires on my gooseneck horse trailer due to age, and a blister appearing on one sidewall while on a trip this past weekend. Currently has LT235/85R16 tires on it. Looking at all the various tire websites is starting to give me a headache, and there also seems to be some...

20' Ridgeline cargo trailer, has 12"x2" drums with 6 x 5-1/4" bolt pattern. Drums have Dexter on the outside, look to be in good shape. How do I know what electric brake kits will fit? As far as bolting the new backing plates up to the axles? The builders plate is just a sticker really, and...

Homelite U10560A chainsaw, cut down a couple of trees, then saw just quit. Fuel filter broke off fuel line inside tank, rotted lines. Replace the fuel lines. Now saw won't start. Checked for spark, gapped plug that's OK. Cylinder is flooded no doubt, pulled cord with plug out and lots of fuel...

Have a 24'x30' pole barn we use as a hay shed, on fairly flat ground. When the ground is saturated sometimes water starts running inside making for a muddy floor. A fellow I work with had the good idea to place a trench drain around the perimeter. Just something about a foot deep, place 4"...

I noticed recently that the fuel filter (I guess that's what it is) has came off the end of the fuel pickup line. So I took the tank off, pulled the lines out. The fuel pickup line is very soft, like it's rotted near the end, I've cut off some but when I try to feed it back into the hole in the...

Found this when cleaning up a brush pile on my property. Has '6818 DA' cast into the back of it. What little paint that is left looks to be MF or IH red.

Am I seeing things, or are there two drain plugs on the oil pan? Drawing in the manual is not very good.

B3200 just hit 50 HR mark. Per manual, need to change engine oil/filter, trans. filter and hydraulic oil filter. But chart shows that transmission fluid not due till 400 HR. Manual shows procedure to change trans oil filter includes pulling drain plugs. So, either: 1) The manual is wrong, and...

For a B & S V-twin, filter is BS-696854. Tired of paying $16 for these things, anyone have a recommended substitute?

Hi all, just joined. Figured I have browsed and lurked long enough.