Search results

Ok guys, can anyone help me with this issue. My 3-pt on my 2350 has been working fine. I’ve been using a box blade to repair some lanes on the farm and suddenly the arms were first stuck all the way up and would only go down when the motor was turned off. As soon as I started it the lift arms...

Just wondering how often you guys slip the clutch on your equipment. Is this an annual necessity or is it ok to go longer

Hi everyone. I have a fairly large JD utility tractor - 65hp with 55hp at the PTO. I need to rototill two areas that are each 1/2 to 3/4 ac. My neighbor offered me use of his new 4’ rototiller that he bought with a new JD 1025R, so pretty small. I’m just wondering if it would damage his...

I have a JD 2350 Utility Tractor with a 245 loader. This doesn’t seem to be a very common tractor but IMO it should be. It’s a 8,500 # beast with a 65hp 4cyl. diesel and a real workhorse. To shift in and out of four-wheel drive I use an electric rocker switch. It’s been working fine all along...

I’m hoping someone else has had this problem and can help me figure it out. I have a 1986 JD 2350 manual 8 spd. transmission. Sometimes when i go to start it it just clicks. If I continue to click it again and again it’ll catch and start. It’s to a point where I’m afraid to shut it off while i’m...

Wondering if anyone has ever pulled and dumped a dump trailer using a 3pt hitch receiver. I had to clear several trees from the banks of my farm pond and now I need to haul the trunks and brush out. The jack on the trailer doesn’t go up far enough for me to pull the trailer with the tractor’s...

Hello out there, I have a 300 gl. Diesel storage tank. I had some health issues this past summer so I didn稚 get as much tractor time as I had hoped, so I still have about 140 gls. Left in the tank. I am in Michigan, so the temps are dropping quickly. My question is, what should I do to make the...

Hi, wondered if someone knows this. My JD Owner’s Manual states, among other things, that the draft links should be extended when checking and filling the hydraulic fluid. The tractor has a front end loader that is not mentioned in the tractor manual at all. It probably has its own manual. I’m...

Hi, so I’m fairly new to tractors and have a question for you folks. Not too sure on terminology, but there is a turn-type lever under the seat that I guess regulates the rate of drop for 3- pt. Implements. With a 6’ box-blade, the rate of drop is very slow on mine, which causes problems when...

It’s me again. I lost the push pin assembly that locks the pto shaft yoke to the tractor. I think that’s what it’s called, but it’s that little spring-loaded button you push to install and remove the pto shaft from the tractor. Went to TSC can’t figure out how those come apart to be replaced...

This question is most likely for some of the more “seasoned” farmers out here. For a while I’ve been trying to gather up some scrap metal for some equipt. reinforcement and what not and I found this in middle of my woods.. This thing has a lot of solid steel parts that I could cut up and use...

Hi folks, I’m new to bigger tractors, only had/have a 1948 Ford 8N. Last year I bought a JD 2350 (65hp diesel, 55hp at PTO) with a 245 loader. It has no stabilizers for the lift arms. I ran it this way with multiple 3pt attachments, including heavy duty brush hog, 3-btm. Plow, back-blade, heavy...

Is anyone out there familiar with how to slip this clutch? It's in an old FMC Sidewinder bush hog. The unit seems to be in pretty good shape but when I get into thick grass it just won't cut. I have to stop, raid it up and put it back down many times. I think the clutch is slipping and needs...

Is anyone out there familiar with how to slip this clutch? I got this old sidewinder its in petty decent shape but when I get into thick grass it just won't cut. I have to stop, raise it for a bit and put it back down many times. I'm thinking it's slipping and needs to be tightened or something...

Hi guys, I have a 4 wheel drive John Deere tractor with FEL and loaded rear tires. My question is, when airing up loaded tires, do you still follow the recommended psi marked on the tires? Do you use air or liquid? What if they are already above the marked psi rating?

I bought a small front grapple for my JD garden tractor and they recommend the installing of a Tow Relief Valve. Problem is, I don't know what that is or what it's for. If anyone can help me out I'd appreciate it. Thanks

Hello from southern Michigan I'm new to this forum and new to farming. 18 yrs ago I bought a small 23 acre farm with the hope of farming it once I retired. I retired last April and needed a tractor with four wheel drive and a front end loader. I found a 1986 JD 2350. It has everything I needed...