Search results

I bought it May 2017.

Same error and won't start again.

After checking several things, but making no real sense of change it started.

The person on Facebook didn't get an answer.

When trying to start the engine won't turn over. It reports 4-1 over u001 on the display. I took out the battery. It has a green light on top and measures just under 13 volts. Does anyone have the service manuals or error code list? Same tractor as MT122 with more horsepower. Someone on the LS...

My SCUT does not have a drawbar (manual says it is optional), it does have a hitch down low. The manual gives some maximum loads for the hitch: Vertical load : 400kg (882lbs) Horizontal load : 1600kg (3527lbs) I bought a chain with a working load above that for dragging logs (and the relevant...

Here is the driving speed from the manual. We mow flat ground in high without a problem. Any slope over 10+ degrees will need to be mowed in low. I know that Rock Crawler did a lot of research last year and would listen to his experience. His hill really is something to deal with.

My portable garage from Costco is 1.5 years old now. It has kept my backhoe and tractor out of the elements until I have a more permanent solution.

This fell apart after my wife swung it 5 times. I think she is putting the kibosh on any more HF purchases.

Placing critical bolts that need to be tightened in an inaccessible location is a design problem. How do you know the single large bolt won't also work its way out? I had taken my rear wheel off and didn't recheck the torque (different tractor). I found out on a hill that only three bolts were...

They are still selling these. $50 at Costco and marked as made in China.

When shopping for my SCUT lift height was something I looked at. The MT125 is as good as the BX80 series for lift height and capacity. Height and reach in the sub compact rage seem to be not that far apart (1-4 inches for many of the measurements). The lift capacity and breakout force do have...

I looked around at used online and new at the local farm store for a rotary cutter. The last place I went was the dealer, and the price was about the same for a much better implement. He gave me a discount for having bought the tractor there last year and I have been in there for some other...

I have assembled one of those 8x15 Lifetime sheds. It is working well so far. Our old church storage shed was crushed by a tree. They just don't make quality buildings anymore. :laughing: Costco had the Lifetime shed delivered for $1,000 + tax. You need add the cost of either a wood or...

The list is on 5-121 of the manual.

That is what a professional is using to dig my house foundation and put it my driveway right now. It can get a lot done, and I am glad he knows how to run it.

Good information. I don't have a GC, but my mower manual states, "The deck is to be operated with the wheels on the ground. The cutting height is set by positioning the wheels in one of seven index hole settings." My tractor manual has a section about using the mower height adjustment knob to...

It has served us well for a year now. Got some holes in it from a lighting strike to a big oak next to it. The bark was blown off the tree, killing the tree.

Picked it up today! I have not used it yet, but I am pretty sure it is the size I want. Made in the USA with a 5 year warranty on the gearbox.

My wife and I are in the market for a rotary cutter. I have never run a rotary cutter. We have a LS MT125 SCUT that we are using to prepare a horse pasture. We have 7 acres of creek and woods, but currently are only working on about 2 acres that were cleared of everything under 4 inches by a...

Did anyone post a picture of the new drain plug? I am around 90 hours now and I had the 50 hour service done by the dealer and he replaced the drain plug. I noticed a wet spot under the front axle of my tractor recently and confirmed it is oil. The attached picture of the front axle shows the...

Lots of work today. Learning how to skid.

I too had my backhoe controls sticking and not returning to the neutral position. The right stick was the one with the noticeable issue. I took it apart to find it wet with corroding nuts and bolts. I wiped it out and used sandpaper to clean off some of the corrosion. I used penetrating oil and...

We just bought a used two horse strait in (title says 1974) with two axles. This is my first trailer, but my wife has hauled horses in the past. The previous owner has replaced the floor, lights, sanded and painted it. They got a third horse and needed to upgrade. The tires need to be replaced...

Lots of chipping in my future. Good thing that I enjoy it. The weather was up over freezing for the weekend, but then it got cold again and snowed.

I have driven mine around our woods quite a bit with the mower off. The only thing that has really concerned me was how dented up the Hydraulic oil filter was (right side pointed to by green arrow). It got pretty banged up before the replacement at 50 hours. The fan is protected by the plate...

Finally got around to taking a picture of the bolt.

Here is it set up to dig.

I weight 200 lbs. I just lift the grey lever in front of the seat and lift up the seat. Lift the lever again and spin the seat (no lift required). When the seat is up there is a pin on the left side that locks it in the up position (I didn't use it at first and pushed back and the seat fell...

The LL1100 loader for the MT125 manual says 1,005 lbs at max height (72") at pivot pins. That is 457kg.

I was looking at a picture of the back of a XJ2025 and see that the wheels are quite a bit further apart than on the MT125. It is just a very small tractor. XJ2025 I found elsewhere on TBN MT125 picture I took yesterday

I ended up taking off both wheels to get on the lower link arms. The bar doesn't slide easily when it is in both sides of the frame on the back. I had to use a rubber mallet to push it out. Because we couldn't pull it out both wheels had to come off. Once we got it out putting on the link arms...

I had the 50 hour service completed and that included the things you mentioned (drain plug, HST relay, and some other items). I bought a used three-point hitch chipper and am looking at putting on the hitch arms. There isn't anything in the manual about actually putting on the link arms. The...

This is the top of the post from the local Farm and Home Supply. I like these posts.

Digging post holes with the backhoe. Need to be 3 feet deep and 18 inches around. I am getting better at keeping them that small, as digging a bigger hole is actually easier.

Just a reminder to clean and protect any wounds. I was holding that green handle on the pallet fork to loosen it up for the first time. It was all the way screwed in when I received it. The handle is so close to those protrusions on the right that it jammed into my knuckle. It barely broke the...

I just remembered that I took this picture of the connectors just before taking them off.

The FEL (LL1100) on my MT125 has a float position by moving the stick all the way up and it pops into that position. The manual says almost nothing about it though. The LB1107 manual has this to say about the float position. I didn't even know it had this till I search the manual. Why was...

So my pedals actually went totally slack. They would not engage the drive at all. The mechanic came out and was not here for long. It turns out that this pin in the linkage between the pedals and that connector rod had worked loose. I was not there to see the fix, but I have before and after...

Ok, the thing I am not sure about is the pedal position. My forward pedal can move by about 3 inches without any resistance. Is that how it is supposed to be? Those are pictures of the top and bottom of pedal movement with just finger pressure. The pedal will stay in either of those positions.

I have found that taking the mower on and off is the most work. BH and FEL are very easy. The first time I took off the BH I did not put anything under it and it sank to the ground, but it was not a problem getting it back on as the hoses were long enough. I started asking about the HST pedal...

I had 4 tons of rock delivered. The MT 125 was able to scoop up a full bucket of the 1 inch clean. We only did that twice, most of the time we were taking about 3/4 full loads. Not lifting to full height except to settle the rock even in the bucket. Still getting used to the loader and trying to...

Thank you! I read some of that thread. Looked at the two nozzles I had (different brands) and was still stumped. I showed my wife and we got a vise grip and wrench. After mangling the nozzle some more I finally got it to turn. I don't know why they tighten it so much, but it is ridiculous! Now I...

I got curious and tried to take some pictures of the backhoe connection point and underneath the middle. Should I cover the mid PTO in some way?

Have you removed the BH or FEL yet? I watched a video on the removal of the mower from a BX and this was similar. Now I will have to see about putting it back on.

I got mine delivered on Friday. $17,719 for tractor, loader, backhoe, and belly mower including delivery to my property (about 15 miles). I also had them bolt on some bucket hooks. They didn't have the mower manual (said that LS has not printed them yet), and said they would get it to me. I...

I just bought a few acres of wooded land with a creek in a suburban area. It is next to some land my parents own and together we have about 9 acres. We have cleared some of the small brush on about 2 acres and want to build a house and stable for horses. I found TractorByNet when trying to...