Search results

Well my 1920 has let me down, inside of the fuel tank is very rusty. I've emptied it out several times and got lots of rust out but there seems to be an unlimited amount. There are no new tranks available for this model but I have a used one on the way. The question I have is to coat or not to...

I have a Ford 1920 that I primarily use to bush hog with. The PTO clutch has never worked well and after I purchased a Ditch Bank Flail mower for it the clutch failed causing a stripped upper PTO shaft. This part was not available from For/New Holland or anybody else for that matter. Ford /New...

Not sure where to put this but I posted a while back a search for PTO part for my Ford 1920. Received a few replies but had no luck finding the part. In the last week I have received 3 emails from new members referring me to different people with gmail email accounts. Contacted two of them...

Looking for an upper PTO shaft part # SBA322570870. Thanks in advance Mike from NC

Title says it all, wanted a Ford 1920 upper PTO Shaft Part number SBA 322570860. Thanks Mike from NC

My PTO clutch went out in my 1920. I have done searches for this repair and see varying degrees of success . What is the best, read most reliable, clutch pack to repair my tractor? I have heard Messick's is good (pricey) others mentioned AI Products. Since the most expensive part of this is...

This is a re-post from the Ford/New Holland forum. Not receiving any help and as you can see I need it to go forward since I have little knowledge of Hydraulics. I have a Ford 1920 and would like to add dual remotes to the rear. I do not have a loader and the tractor is kept 60 miles from my...

I have a Ford 1920 and would like to add dual remotes to the rear. I do not have a loader and the tractor is kept 60 miles from my house. Looking at the Service manual it looks like I could add the remotes by accessing The two ports of the Combination System Relief and Diverter Valve Manifold...

I am in the process of adding rear remotes to my Ford 1920. I am trying to locate, or fabricate if necessary, some sort of bracket to hold the four hoses with quick disconnects in the rear of the tractor. I have seen them on tractors but I have done multiple searches and I would guess I don't...

I recently purchased a Ford 1920 that came with an older 5 foot Hardee Rotary cutter. I can't find any ID numbers on it and it needs new blades. Is there a normal size for a 5 foot cutter or is brand/model specific? I can try to measure the ones on there but they are badly worn so I don't know...

My neighbor, who buys and sells tractors for a hobby, showed me his Oliver 1365 yesterday. Ran great no issues there but the PTO operation was confusing. There is a lever on the transmission case below the gear shift that moves side to side to engage the PTO. There is also a long lever that goes...

As the title states I just purchased a 4 foot Bush hog for my B1750. Just wondering if I need an Over running clutch? Thanks in advance Mike

Has anybody rebuilt their bucket cylinders on a 1640a loader. I don't see any real outside leaks but the bucket is dropping at an increasing rate. It just started after I moved about 7 large pines that died as a result of flooding due to hurricane Florence. I had cut them to manageable lengths...

After a long search I located some turf tires and wheels for my Kubota B1750. One if the rears, a 29 X 12.50 - 15 turf, has a leak around the rim. The tire is loaded with Calcium/ water. I need to find the right tube for it but so far no luck. Any ideas, I've looked at Ebay and Amazon, and...

I really would like to find some turf tires, which as I understand it, also would recall some new wheels. The current tires are ags which are ruining the yard which is normally wet. The current rears are 9.5 ×16 and fronts are 6×12. Anybody have any ideas where to look for some? Thanks, Mike

I am trying to figure out what I need to add "The Thumb" to the above tractor. It was suggested by customer service that a diverter valve from surplus center, part # 9-8602 would be an easy way to add the Thumb. I have never messed with hydraulics other than replacing hoses so forgive me if...

I would love to a The Thumb to the bucket of my B 1750. I don't know anything about hydraulics and looking at a 3rd function valve and hose kit it looks at twice the cost of the Thumb. Am I missing something? Just went through a major hurricane and it shure nould have come in handy. I have no...

Is there such a thing as an electrically powered thumb or grapple for the FEL on a Kubota B1750. Just finishing clean up after Florence and it sure would be nice to be able to pick up brush with the aid of a grapple or thumb. I've seen the ones that have to be plumbed into the hydro system...

My IH Cub Cadet 124 was running fine. Ha her out an running for about an hour 2 weeks ago. She was irty so I took her out again an last week an cleaned her up. A couple of days ago went to start her up (new Battery 2 weeks ago) an starter generator would just spin not turning engine over. After...