Search results

Hello I got on a diesel forum and saw a guys video where he mixed 2 parts marvel mystery oil with one part Howes lubricant. I put a 12 ounce bottle of the mix in our 2006 pre DEF sprinter van(the million mile motor) with every fill up. Before using the mix: about every 500 miles I would have to...

Come to think of it I am going to have to spread out the underbody frame parts I have and take a better look. The one set was marked as being off of a 4310. U would still need the front frame J pieces and those front trailing arms and that horeshoe bracket on top of the deck. Just rambling here...

Well, to answer your question NO I have not sold the mount frames and brackets and hydraulics that I have. I no longer have that 4200 or 4400 tractor. I have now a 4210 with a mid PTO that I would like to come up with a mower system for. The tractor black frame brackets that I have will not...

I restored a 4400 JD tractor ...tractor #2 off the assembly line with barely any hours on it but had sat outside for many years and I used 80/90 weight gear oil in the front axle. I figured it would protect better and not seep through the original seals.

I saw a youtube video then went out and tried it. Do not know whether it helps or not. 2006 Mercedes 5 cylinder diesel sprinter(No def) MH and 2014 chevy cruze diesel. 2 parts MMO and 1 part Howes Lubricant in the diesel fuel every fillup. about 10 ounces in the 16 gallon tank and 16 ounces in...

sorry this was in my junk mail

I think i have all of those parts I took it apart and trashed the housing for lack of room. but kept all of the guts cause they looked so nice i think i have the shafts too

I am sorry sir but I do not have that line. I have the main pressure line from thte pump and the big pickup tube regards gary there is a guy in greenwich ohio that might have it 419-685-2264

Ok you need one of the loader joystick lines. Will look early tomorrow and let you know. Tomorrow is fine...I am in Gahanna on the east side of columbus

Hello WHich line is it I still have some lines but marked them with water based marker. Do you have yours off that you can send a pic with a dollar bill in the picture

Hmmm will ponder that if i get to it Thanks so much gary

I bought two 4200's and a 4400 and they fit nicely on a car hauler trailer uhaul. well i worried about the inside width of their rails but they hauled nicely. Long story there anyway a car hauler should work. will measure one to be sure thanks gary

Thanks I figure if i keep the hoe boom up high and swung to one side and curled all in that should cut down on the needed trailer length. probly should chain it up in case of drift. thanks

Hello from Ohio, I am thinking of buying a JD 4200 compact 4wd tractor with 430 loader and 48 backhoe with a wide bucket. I am going to have to rent a uhaul car trailer to drag it a long way home. Question: Which end is the heavier end of this setup? Should i pull it on or back it on the...

Hello from Ohio, I am talking with a fellow that has a Kubota X1100C RTV that has a blown transmission. Apparently you can see daylight through the casing. Do not know the model year. He is a few hundred miles away and the price seems more than fair. I have not seen it but I am a full service...

Sorry this ad was placed a year ago with no way to edit it I sold the pump last year Hope you fine one gary

Hello I am sorry but I just sold the right sida housing and the left side was sold last year. I do not know how to edit the ad to remove those parts. Again Sorry and good luck Gary

I would limb it first. It is not gonna go downwards. I would pay real close attention as i am limbing it to see if it raises upward as the limb weight lessens. That should tell you how much pressure the stump is having on it. If the stump is pulling up pressure then notch the top of the log...

Hello Yes I have both. the mid handle that sits left side of seat. It is used and the rubber handle part has been removed from the arm so i could clean and paint the handle. It will need boiled and water and inserted back together while hot.$30.00 the dash mounted rod and latch bracket that...

I have had them all away apart. Hydro and sync shift. The range selector is just a gear drive, 3 different rear end gear speeds. Totally different from the Hydro. two different systems. Check the rear sight glass for hydro fluid. Both use the same fluid. If it is low and the range shift fork...

Hello I had a 1970 something mercedes 220D and in the owners manual it said that if you could not find a diesel station you could fill up with low grade gasoline with one quart of motor oil.. It really did say that

In the original advertisement (the price per rules) "This isn't a bargain basement deal so don't go there. A New one will cost you at least $25,000.00 ...I figure that is a fair starting point for this Nice Machine" Not trying to be cocky but it is in there. regards

Not all... The drivetrain

Important John Deere 4400 Tractor mfg 1999 W/60 hours From 1999 through 2001 John Deere manufactured well up into the many Thousands of model 4400 Compact Tractors. I offer you The Second 4400 tractor ever built with less about 60 original hours on it.<BR> It is a Numbers Matching tractor. The...

If you have welders you ought to have a torch I would either clean all the paint off within a half inch of the area to be welded and gas weld it OR I used to take a thick piece of brass that fits up tight to the weld area and hold it behind the weld area(it absorbs the heat) and sputter the...

I had the same thing happen to me once.... About 15 years ago we had a major ice storm here in central ohio Storm of the century 2005 2006 roughly. Power was out for over a week. Brush piled up both sides of every street like after a hurricane in coastal florida. Trusty generator and wood stove...

Seen a couple stuck pins in my day... On your hydraulic press jig there which looks really nice by the way... Most all hydraulic cylinders have from a little to a lot of side to side clearance on the shaft. if you take out all of that clearance then put as much pressure on the pin that you are...

dampen everything and sprinkle baking soda around any parts that were affected to neutralize the acid. Fizzing up will tell you if it needs more. 48 hours into a 3 day repairing snow equipment shift some years ago had a welding spark explode a battery 2 feet from me. Really fortunate that only...

Well I actually have most of the missing bracket(see photo.) The other piece of it is here needs welded if i find it. Look at the phorto's below...both yours and mine are basically the same except i have a 3 spool where you have 1 spool. The 3 spool valve extends out to the right and the lines...

Hello, I have pretty much the complete hydraulics and Joystick to run a Front end Loader. What I have is pretty much everything on this JD parts page: https://partscatalog.deere.com/jdrc/sidebyside/equipment/69332/referrer/navigation/pgId/240211192 EXCEPT for #'s 1, 12 and 29 and 2 of the...

Should I reply? I do not understand your reply. I have most of the parts if you need any. Located in central ohio thanks

Well i have checked the continuity of the alt wire. I am leaning toward the pulse thingy in the alternator. When it gets cold i will head back in to have it checked I suppose the new instrument cluster could be faulty but all other functions seem to work fine.

Well the 1999's did not have a computer so no microprocesser. I was told the tach and hour meter on mine both run off of the alternator pulse. BUT my hour meter works while the tach does not. 4000's deere fuel guages go bad a lot. ususlly the tank sender. On cars the temp sending unit in the...

Hello I am disassembling a 4200 john deere tractor Hydro with 4wd. ser# LV4200H321983 Deere does not show many internal parts on their exploded views of the rear end on this 4200 tractor. At least not that I can find. I found some of...

Good Morning from Ohio, I have some good parts left over from a John Deere 4400 Restoration project. These parts are from a 4200 tractor. The parts from a 4200 4300 and 4400 actually any 4000 series tractor from 1998-2001 are interchangeable, I believe. Verify your part numbers. I have the...

I like your stands They are pretty ingenius I am actually disassembling the 4200 to part it out. The hydro ID tag is attached to that housing over your bucket and I thought the hydro unit came off with that housing. I am going to have to relook at it in the morning. I looked at those hydro...

I am trying to remove the hydro section from the next to rear housing on a 4200 john deere hydro tractor. (see pics) Motor is already off there are three remaining sections: there is the housing where the hydo is encased. then there is the section that housed the driveshaft and I am guessing the...

If you have not repaired it yet I would think that any hydraulic shop should be able to come up with the fittings you need. I am sire the valve was not made by deere but someones off the shelf part. Especially since their SCV supposedly 2 spool valve is actually a 3 spool valve. I have the...

I am just about finished repainting a John Deere 4400 tractor. This is #2 4400 tractor to come off the assembly line in Georgia. Serial number LV4400H140002 build date 08 june 1999 37 hp Yanmar 3TNE88 Motor Hydro Trans Cruise Control Mid PTO Telescoping 3 point arms NO COMPUTER NO Exaust Fluid...

I still have the tractor for parts. thanks gary

Really Good Thought Scotty He is an older guy that pretty much has his guy fix stuff anymore but he tested this himself and I am sure I told him the tach runs off of the alternator and he said it was fine. Us Old Folks Ha ha

Well in my original post an auto electric guy i have known for many years says the alternator is doing whatever it is supposed to

zSince I really do not know what I am looking for would you be so kind as to give me a link to an amazon signal generator for sale regards gary

It must be the engine on hours It does not increase with key on only

I have no knowledge of a signal generator. will research it. I believe there is a pole on the alterntor that supplies that pulse. How would one test that? Thank You

Thanks I have done that many times. I have been over under inside and out and it will not work. BUT the hour meter works which is confusing It is a new aftermarket dash cluster. Under advisement it just felt right to put a new unit on a tractor with so many obvious signs of low hours.

I really do not know I have read that the hour meter works off of the power supplied to the tachometer

Am in the process of restoring a 1998 JD 4400 Tractor with around 50 total hours on it from new. I have about 3 hours run time on it myself. The tachometer worked fine and just quit all of a sudden. The hour meter works fine. ALL of the factory safety's are functional. This is a pre computer...

Be careful with the fuel shutoff relay. You might think that if you just put 12v power to that relay that it would fix the problem WRONG The solenoid will burn up if you use a constant 12 volts to it

Fastline.com tractorhouse.com All States ag parts

Well i really do not want to part out a good working 3 spool valve. There are a number of tractor salvage yards online that might be able to help Regards gary

I still have the tractor and I believe the parts will fit a 4310. Let me know exactly what you need parts number wise and we will go from there.

Hello with the tires on it is hard to get a good picture of the rops mounts. the tractor mfg june 28, 1998. The rps came off of q 200 year 4200 tractor. The rops angles backwards from the tractor. on mine there is a hole im the middle outside of the bottom plate of the actual rops. that should...

Hello, Thought I would undate you all on where I am at with the restoration. Haven't done much in a month but here is where she is at. Have been out driving it around. Hooked up the loader and it works fine. Needs the grille fitted the rear fenders repaired/cleaned up and installed, the seat...

I have a Fiberglass hood for a john deere 4400 tractor. It is tractor number 2 ever built. regards gary in ohio

Thanks. I am thinking $7,000 for the 4200 tractor as she sits. It is a sweet machine. regards Gary

John Deere 4200 Tractor 26hp 2wd This is a pretty nice JD 4200 Tractor. MFG from 1998 to 2000 ...Yanmar 3TNE78A Diesel engine 26+ Horsepower ...2750 hours Purrs Like a Kitten ...Power Steering ...1 finger control ...Tilt Steering Wheel ...3 point hitch Category 1 ...Rear PTO 540 rpm ...Mid PTO...

Hello from Ohio, I have pretty much the entire mid mount mower lift assembly, I was told is for a 4310 tractor. I have no idea what all other models it will fit. The main components are here...May not be complete. What is here: The rockshaft, rockshaft mounting pillow blocks, The hydraulic...

Hello from Ohio, About 20 years ago we had an ice storm and the electric was out for more than a week. I ave a wood stove and generator so no big thing. The power came back on and everything seemed to work but the microwave would not get hot. There ere Power company crews everywhere so I started...

I appreciate all of your comments. There is a number of reasons that i feel this machine was never used; Although it sat out in the elements for many years with only the hood on it for covering. There was no "NONE" buildup of dirt/sludge on any of the recesses you would normally find it. The...

I have a John Deere Tractor that I am selling whole as a parts machine. Parts from this tractor will fit 4200 4300 4400 4500 4510 and others I am told. This tractor is a 2000 John Deere 4200 tractor serial # LV4200H321983 4 wheel drive with Hydro Transmission and loader control valve with...

Thank You for the interesting comments. PTSG Wonderful job on your Crawler. Thanks for the heads up on the oil I will keep that in mind. Yes I have the panels on order...Aftermarket. As for the guage cluster, I agree with you all that this machine has very low hours. I had bought a donor machine...

Hello from Ohio, You know how after each oil change on a diesel, the oil gets dark in color immediately. I have a Yanmar 3 cylinder 37hp motor , build date roughly June 1998. Question: From NEW how many operating hours does it take before the motor oil starts to darken in color? Nice Problem...I...

Hello, I need help...at least knowledgeable opinions. I bought a John Deere 4400 tractor that had sat for many years without sheet metal. It was pretty much sealed up BUT They left the inlet and bypass hose bibs of the injector pump open with the nipples pointed up. From what I can see through...

Hello from Ohio New guy here...Thanks for the Forum I have been an equipment mechanic/Welder/do whatever it takes now for many years. Our Lord has blessed me with many talents and the ability to make many mistakes through the years. I ran across the forum and thought I should jump in. Grandpa...

Hello All, I was an equipment maintenance mechanic for many years and also mowed with the Farmall Cub Hi Boy that Grandpa bought the year I was is born 1951. We are now looking for a place with less property taxes and a little acreage So I bought a John Deere 4200 tractor that had, well it...