KentT
Elite Member
- Joined
- Mar 31, 2005
- Messages
- 2,928
- Location
- Sevierville, TN
- Tractor
- 1993 Power Trac 1430 w/Kubota diesel engine
I'm going to pick up the new-to-me old 1430 with 3-pin hitch tomorrow and swing by Tazewell to get a ROPS/FOPS and talk to Terry about how to convert it to QA. Will have the following duplicate attachments for sale. Posting this here, before I start pulling them into the garage, cleaning them up and listing them for sale in the classifieds here and on PT's site. Special pricing now, before I do that chore. Preliminary pricing is less than 1/2 of the new attachment -- all are in usable condition. I will put on a pallet and ship via Fastenal at your expense (I have some pallets). Quantity discounts available. PM me for pics and discuss pricing.
1. T-12 3-pin snow/dirt blade. Condition unknown (only attachment I have not seen -- it was stored separately) but should be OK, since the 1430 and all four attachments had only accumulated 497 hours.
NOTE: All the T-8 attachments below have QA plates.
2. T-8 60" finish mower. New blades, belt and arbors last year. Caster wheels/tires have been replaced with solid rubber tires on greasable wheels.
3. T-8 48" brush cutter. Motor leaks (though usable) and I have new Surplus Center replacement, never installed. Front casters replaced with solid, bush-hog type tires with greasable hubs. Rear tires replaced with wider wheels, solid rubber tires and greasable hubs Minor stress cracks, not repaired.
4. T-8 48" light material bucket that I bought new, in good condition without damage.
5. T-8 45" grapple bucket with teeth that I bought new. Bucket was stress cracked and repaired. Two outside grapple teeth/fangs bent. Good usable condition.
6. T-8 45" HD rock bucket with teeth that I haven't used since I bought the grapple bucket.
7. T-8 forks that have seen little use. One fork has been bent and straightened.
8. 48" King Kutter XB (Kubota BX class) boxblade with adjustable rippers and replaceable cutting edges front and rear, modified to T-8 QA. I bought it new and had the QA plate welded on.
9. 60" Howse landscape rake, with solid-tire casters and manual angle adjustment. T-8 QA added by previous owner.
1. T-12 3-pin snow/dirt blade. Condition unknown (only attachment I have not seen -- it was stored separately) but should be OK, since the 1430 and all four attachments had only accumulated 497 hours.
NOTE: All the T-8 attachments below have QA plates.
2. T-8 60" finish mower. New blades, belt and arbors last year. Caster wheels/tires have been replaced with solid rubber tires on greasable wheels.
3. T-8 48" brush cutter. Motor leaks (though usable) and I have new Surplus Center replacement, never installed. Front casters replaced with solid, bush-hog type tires with greasable hubs. Rear tires replaced with wider wheels, solid rubber tires and greasable hubs Minor stress cracks, not repaired.
4. T-8 48" light material bucket that I bought new, in good condition without damage.
5. T-8 45" grapple bucket with teeth that I bought new. Bucket was stress cracked and repaired. Two outside grapple teeth/fangs bent. Good usable condition.
6. T-8 45" HD rock bucket with teeth that I haven't used since I bought the grapple bucket.
7. T-8 forks that have seen little use. One fork has been bent and straightened.
8. 48" King Kutter XB (Kubota BX class) boxblade with adjustable rippers and replaceable cutting edges front and rear, modified to T-8 QA. I bought it new and had the QA plate welded on.
9. 60" Howse landscape rake, with solid-tire casters and manual angle adjustment. T-8 QA added by previous owner.
Last edited:
