Quick Hitches Land Pride Quick Hitch

[Piston]

Thanks for the pics Richard! I will see if my top hook will clear, and if not, probably do something similar. I hope it fits the way it is though.

I've decided to buy the Land Pride quick hitch. I'm getting the floating top link kit with it as well, and it comes standard with one set of bushings. Are you guys with QH's using the lower bushings on all your implements? It seems like there are two types...






Is there a need for one type over the other? What is the practical difference in these?

I don't understand why the lower hooks on the quick hitch aren't perfectly matched to standard cat 1 pins? Maybe so you can still use cat 2 implements as well?

 

[MtnViewRanch]

Thanks for the pics Richard! I will see if my top hook will clear, and if not, probably do something similar. I hope it fits the way it is though.

I've decided to buy the Land Pride quick hitch. I'm getting the floating top link kit with it as well, and it comes standard with one set of bushings. Are you guys with QH's using the lower bushings on all your implements? It seems like there are two types...

View attachment 354135


View attachment 354136

Is there a need for one type over the other? What is the practical difference in these?

I don't understand why the lower hooks on the quick hitch aren't perfectly matched to standard cat 1 pins? Maybe so you can still use cat 2 implements as well?

I believe that the bushings with the shoulders are intended to be used with single side mounted pins and the straight bushings get used on clevis type mounts. I agree that it seems strange to me that the QH is not just built for either cat 1 or 2 pin sizes. :confused3: I don't see how you could use a cat 1 QH with a cat 2 implement. Spacing is wrong width and height, although most QHs now have height adjustment. But how quick is it if you have to get off the tractor to always be adjusting the top hook? :confused2:

I know that this has been said before, but a QH is only quick if it works on everything without adjustments. Otherwise you are just changing what it is that you are having to adjust.

Just my :2cents:

 

[murphy1244]

I used both syle of Bushings as some are clevis style and some are pin. Here's a link for the cheapest price that I found Three Point Hitch Parts

 

[bcp]

I use the simple bushings on pins. No problems yet.

Bruce

 

[Deerherd]

I don't understand why the lower hooks on the quick hitch aren't perfectly matched to standard cat 1 pins? Maybe so you can still use cat 2 implements as well?

There needs to be that raised end on the bushing for single sided pins or the implement could fall off. I believe that is actually cat III outside diameter. There are Cat I to III bushings and Cat II to III bushings. The only difference between the Cat I and Cat II QH is distance between the arms. (Probably on how heavy they are built also)

Everything I have is Cat II QH compatible. Combined with Top-n-tilt, it makes hooking up a breeze!

 

[bcp]

There needs to be that raised end on the bushing for single sided pins or the implement could fall off.

No, it can't fall off. The QH hook against the frame on the other side prevents it. You don't even need the locking pins, except to keep the bushings on.

Bruce

 

[Deerherd]

No, it can't fall off. The QH hook against the frame on the other side prevents it. You don't even need the locking pins, except to keep the bushings on.

Bruce

I have a couple Cat I pin implements (cable/pipe layer, single ripper and trailer coupler)that I used longer pins and adapters on for my Cat II QH. It WILL give you enough room for it to slide out of a Cat II hitch. Don't ask me how I know! :ashamed:

 

[GreenWannabe]

I bought a Woods Cat 1 quick hitch with my tractor, Once I was finally able to take delivery of it this fall (!) I started working with my implements to insure they all fit my quick hitch. I do have FitRite's top and tilt cylinders installed on the tractor - absolutely wonderful! I bough a few extra adapter kits at the same time, and the dealer installed one of them on the Woods BB72X cutter for me, which has clevises. I think I would have used the straight bushings for these instead. I couldn't find the top link bushings I wanted, and wound up buying them from LandPride as well as straight bushings, as they are listed as parts for their quick hitch.

I had no instructions for the Woods unit, so emailed them, and they emailed me back a two page instruction sheet. On that sheet, I found that one adapter they included with the hitch was for use connecting an implement which was compatible except for the top link. It attaches in place of the top link on the implement, and the clevis fits the quick hitch properly. The adapter looks like a lower case "h". except that the upper part comes off the middle of the lower part instead of the left side. Woods part number is 1024575, and from the diagram appears to include the hitch pin. I've ordered another one from my dealer, since I have two implements, a spreader and a subsoiler, which are not quick hitch compatible. I'm sorry, but I don't have the part number for the category II adapter. I got my parts list from Woods the same way, by emailing them, since it is not listed on their web site.

For those of you who have Gannon box blades, this could be the answer you need to make them three point compatible, especially if you have a top cylinder.

 

[ovrszd]

Piston, the reason you are supposed to use bushings with a QH is to create a wear point. If you hook the QH directly to a fixed pin, everytime you raise and lower the attachment the pin is rolling in the QH bracket. One or the other is being ground away. Neither is good. So a CAT I QH lower hooks are always CAT II. A CAT II QH lower hooks are always CAT III.

As for bushings, The shoulder on the second ones you pictured are designed to keep the QH from sliding off the end. The thing I don't like about those bushings is that tools are required to install/uninstall them. If you have multiple tractors and only one QH you might find yourself needing to remove them for use on the non QH tractor.

I prefer the cheaper, easier to use straight bushings like in your first picture. Here's my solution for keeping them in place and preventing the QH from working against my latch pins.

 

[classacthollow]

I didn't look when I bought my quick hitch and ended up with the cat. 2 unit, so instead of buying a bunch of bushings I just changed all the pins so I didn't have to worry about the clevis's popping off and loosing the bushings.