Recent content by pruntyc

I priced the 200CX for my 4110 at two dealers in my area, and they both want $2950 installed.. Isn't that a little high? Someone said earlier it should run around $2500 installed. So who is right, I don't have all that much money that I can spend more than I really have to, on one.

I didn't buy a loader with my 4110. Now I'm thinking I may want to add one, one of these days. So wondering how much money they are asking for one, you know a ballpark figure. I know it might have been cheaper to have bought it when I bought the tractor. But that is water over the bridge...

I finally got my dealer to give me a hand grip for the right fender, bought the tractor in Feb. He sent it to me, and when I look it don't fit like I thought it should, as the holes in the fender are not in line, like on the left fender. I have to move the top hole in about an inch to go in...

I notice its a little slow to start when the motor is cold, I don't mean real cold outside eithter. Like today, it was in the 50's and it was slow to start. The manual says I should hear a click. But I don't, so I wonder if they are working. After it is used it starts fine. Is there some...

Well. not having a problem getting the 4100 fixed that the dealer didn't want to do what he said he would, with the bad tires. I bought a new 4110, and got it this after noon. Only has 1.4 hours on it, so it hasn't even been tried out by others. I found out the folding ROPS are taller than the...

Having just traded in my Yanmar for a 4110, I get tomorrow. I was wondering, the old Yanmar had a decompression lever, to make it easier to start when it was cold. And it helped get the motor spinning so the oil pressure could come up, before the engine started. As the new Deere's don't use...

Is there anywhere else to buy these filters. I know Deere is high priced. You know like Baldwin or Wix or Napa. I can buy the other filters from Napa, but not sure they carry any for the transmission. Thanks

How is the price of $12,600 for tractor only? He has to go to another state to pick it up for me. My used deal has fell through, so I asked about a 4110.

Does Deere furnish the tires, the dealer put on? Or do they have to buy them elsewhere? My dealer told me, he has to look for a place to buy the tires, he is putting on mine. But they would be the same type.

I read in the manual that my tires on the 4100 calls for different pressure. One calls for 12 lbs, and it says unloaded, then it says 41 lbs loaded. I just don't understand what it is trying to tell me. What does it mean loaded and unloaded, and why so much difference in pressure? That is...

I didn't get a manual with my used 4100. I told the dealer they have the manual on line for the 4110 couldn't I just use it. He said no, there is a lot of difference between them, I wonder if he doesn't just want to sell me one. So I figure you guys would probably know, is there really that...

I went back and bought the 4100. He gave me the $2500 trade in on my Yanmar. And everyone else would only give me $1500, including him, on a new one. So I guess if that is the wholesale price of one, then he wouldn't lower the price, but in that way he did, so I guess I bought it for $7500...

I'm still trying to make up my mine which replacement tractor to get. Does anyone have a 2220 2wd? If so how do you like it? I think I might get one, as I have a gravel drive up a steep little hill. My 1700 would spin a lot, when trying to grade uphill, and that is the way I need to, as the...

I am looking to get a different tractor. I am looking at probably getting a 2210. I thought about getting a 2220, because it is heavier, but then I read it has wet brakes. Hmmm, I have had dry brakes on everything I have ever owned and can work on them. So I guess the wet ones makes the...

I know the 2210 has 3 forward and one reverse in each gear range. But then how many gear ranges does it have? Does it have a creeper gear range? And is that included in the ranges it has, like if it has 3, does the creeper make 4, or what ever amount it has? It looks like I may be going...