Recent content by torrin

I have a B2650HSDC My back blade is messing up my gravel drive when the snow is too wet for my front mount Snowblower. I have a chance to purchase a used 60" quick attach snowplow blade but I need the piece that attaches to my quick attach underframe. If you are not aware, on this tractor you...

Good evening; I am currently investigating purchasing a B3030 cab. it has rear and mid pto. I want a front snowblower (2+ miles of trails to clear) the model that I have seen is B2782a. I can not find any oyher information then that. Is that a quick attach? What is the sub-frame part...

Good Morning; I have a LS XR3037LC with 160 hours on it. (new to me) My problem is that I can not get the bucket to stay in position when pressure is applied. When Making a skim or shallow cut into the ground, the bucket goes all the way down; digging much deeper then my intent was. Also...

Good morning; I recently purchased a BX2230D. The previous owner told me there was a "small" leak when you raised/lowered the MMM deck and left the lift control out of the neutral position. He stated that he could not find the leak, but it left spots on his garage floor. I found the leak...

Good Morning; I just recently purchased a BX2230 (670 hrs.) and would like opinions about hydralic and engine oils. My old BX1500 used only Kubota oils, but they are pricey. Is there a good alternative to these oils out there?:confused:

Good Morning; I recently purchased a used (670 hrs.) BX2230. I have done all of the maintenance and adjustments on it to bring it up to date. I did discover one problem that as of now has me stumped. When mowing, I lower the deck and if I do not manually return the lever to neutral, when I...

I have a Kubota BX1500. One of the nozzle covers on the FEL quick disconnects has become lost. Are there any nozzle covers out there that I can purchase that do not require me to remove the nozzle? How do they attach so i will not lose them when using FEL?

here are the pics. I was wrong on the coating, it is not real thick

Good evening; I was going through my rod to make sure I had enough for the project that I am working on. I came across about 5 lbs. of red coated unmarked 1/8" rod. The rod itself is almost black, and I thought that it might be iron rod for doing cast iron work. I inherited the rod when...

Good Morning; I am a long out of practice welder who has a project the is causing me to question my sanity. I bought a used lawn roller cheap and need to rebuild the hitch frame. My buzz box (Lincoln 180) only seems to work at over 100 amps (7018 1/8" rod). It is blowing holes in my tubing...

My 90 year old Father-In-Law is looking to buy a tractor. He has priced a Mahindra 3616HST and a LS XR3037H both with mid PTO, FEL, front snowblower, and cab. His quote was approx 32K for either. I know nothing of tractors of this size, but these prices sound reasonable to me. Both are tier...

Attached is the page from my RCK48-BX15 dek parts book. Spindles should be the same

Good evening. I have an opportunity to upgrade from my current 2005 BX1500 with just over 500 hours to a 2008 BX1850 with just under 500 hours. 48" to 54" MMM. FEL on both. Possible difference in cost of $1500 to $2000 based on what i see 1500 w/FEL going for. 1850 is on my dealer lot, but...

Ladies And Gentlemen; I have a BX1500 w/FEL. I have a dirt moving project that involves leveling an area to accommodate a parking space. (Company truck) My question is, is my FEL strong enough to put a bolt on tooth bar to remove the clay base turf and possible tree roots. I am aware of...

Good Morning; This may be an off the wall question, but I own a BX1500 and work on a B3200 (new, 90 year old father-in-law). Both have Front mount snow throwers, and both lower one side to the ground before the other. Is this normal? I say this is strange because this is my 3rd winter with...